To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 7501 (+100)
  Re: Wot no RCX power connector?
 
Sorry for the imprecision. It was the RIS (the whole kit with the few new pieces). Mike The WordMeister <lego-robotics@crynwr.com> wrote in message news:01bf1a3a$3fad23...ici.net... (...) price (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
What new pieces are there in the RIS 1.5? I don't suppose maybe a second differential gear? No, probably not... Was there anything really glaringly useful? -Andy Lynch Mike Kory wrote in message ... (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: AI and even more exiciting stuff
 
Ralph Hempel wrote: [ good rebuttal snipped ] (...) Actually, I went through two years of a systems engineering degree. (before finally dropping out) During that time I had many semesters worth of math and CS... however, not one of them went over (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) I doubt there will be significant changes to the ROM. For starters, if somebody has both an old and a new RCX, try downloading the old firmware into the new RCX. If it works, the ROM interface is the same. If the ROM interface is the same, it (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) Wait a minute... Doesn't the RCX hold its firmware across the auto power down? I thought it did. That being the case, all you'd have to have done was turn it back on, no? -Kekoa (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
No, while the RCX is in an "off" state, the firmware is maintained via a trickle current (something like the CMOS registers in an personal computer) supplied by the batteries. When one removes the batteries, the firmware and any stored programs are (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: AI and even more exiciting stuff
 
(...) [snip] (...) I wasn't them... I was involved with the control system algorithm development and analysis. This bunch was definitely not using a tool -- they were doing it all by hand. I'm sure they were not doing it right either because (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) I've read that the end where the power connector was is "thinner" which is OK since the connector was mounted on the component side and would have added to the hight required. The "smoothing caps" could be eliminated in a battery only design, (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
I've changed batteries often and have never lost anything. I turn the unit off and swap the batteries quickly. Mike (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: AI and even more exiciting stuff
 
(...) I've done simulations on spreadsheets and simple scripting languages when it was too much bother to get the C compiler running properly.... (...) Oh Oh, don't tempt me. Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) Hi all - I'm new to this list - why? - I just got my RIS 1.5 last week (RIS 1.0 was never available in Denmark - as far as I know) - someone in RTL asked me for a scan of the new lego's in the RIS 1.5 - so I uploaded a scan here: All bricks: (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
Was that a 1.0 or 1.5? I'm hoping it's just the 1.5's, since there are still 1.0's around. I can't believe there wouldn't be an option for wall power (even with a funky idiot connector to prevent overvoltage). What about models that have large (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) Actually, there's a ton of space left in the ROM, I wonder if they ADDED anything useful, like a real OS kernel :-) <<<<< I suspect they had to leave it alone, sadly. They have to maintain both forward and backward compatibility, otherwise (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) Interesting enough, I once withdrew the power connector on a unit under full load - sensors, motors, everything on - because the task manager had gone into an endless loop. After duly waiting a couple of seconds, I reinserted the plug. Blue (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) It was a 1.5. I wonder what you get if you order a separate RCX now? I would hope ones with a power connector would still be in stock. (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) I don't think so - it looks the same shape as the pictures of RIS 1.0 RCXs I've seen. I doubt they would change the external shape as it would cause problems with plans in expansion kits etc. I expect there's just a lot of empty space inside. (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  new pieces (was Re: Wot no RCX power connector?)
 
From: "Jesper Kjaer" <jesperkj@vip.cybercity.dk> (...) Any idea what the blue brick 4 rows down in the last column is for? It looks very strange. The double yellow connector (3rd column, 12 rows down) is kind of interesting as well. I don't think (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: AI and even more exiciting stuff
 
(...) When will it be on Amazon? -Luis "anxiously awaiting Ralph's pearls of wisdom" Villa ###...### Profanity is the one language that all programmers understand. -Anonymous ###...### (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) HaHaHa - What about the one Dave Baum developed NQC on, and the one you used for LegOS, and the one I used for pbFORTH? I'll bet they would sell as a matched set. I can see it now...... I guess if Kennedy's golf clubs are worth $750,000 these (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
Thanks very much for posting the scan of the 1.5 bricks. It's helped answer questions we've all had about what "new" stuff would be included. Of course, now we all want to find out exactly what some of them do! I suppose asking for scans of the new (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: new pieces (was Re: Wot no RCX power connector?)
 
(...) They use it to connect sensor mountings to the robot chassis in the Constructopedia robots. The chassis and sensor array each have one of those blue things, and they are locked together by the double yellow connector, which can be inserted (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: AI and even more exiciting stuff
 
Well, I was about to ask if someone wanted to write up a simple fixed-point tutorial for my web site (it's a little sparse and could use some articles like this). However, I knew 90 people would come out of the woodwork to point me two tutorials (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
I wonder what's in the 1.0's with the 1.5 sticker on the front? KL (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  new pieces (was Re: Wot no RCX power connector?)
 
(...) I'm not sure if this was in the Contructopedia for the RIS 1.0 - but there is 2 pages at the end that shows how to use it - a final pic is here: (URL) description says: This is a prototype so that the inventorbot can move forward and turn (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: new pieces (was Re: Wot no RCX power connector?)
 
Wow! Those look incredibly useful, especially for the mechanically impaired. Can they be bought separately? -Luis (...) ###...### Profanity is the one language that all programmers understand. -Anonymous ###...### (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: new pieces (was Re: Wot no RCX power connector?)
 
Thanks for the scan. OK, so we got a slip disk (4th column, 6th item) - very nice. The RDS has one of those, too. So does the Technic motor set. The blue connector (5th column, 5th item) is used in other sets as a quick-connect brick for modules. (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: new pieces (was Re: Wot no RCX power connector?)
 
Never mind... to answer my own question, and for those of you who are interested- (...) ###...### Profanity is the one language that all programmers understand. -Anonymous ###...### (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) It's exactly that - a RIS 1.0 with a sticker on the front. I just got one, and it's the original kit of parts and an RCX with the power connector. The reason for putting stickers on old boxes is to avoid stalling sales from people who really (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: new pieces (was Re: Wot no RCX power connector?)
 
(...) A-ha! I was wondering whether any set apart from the motor set would ever have one of those. (Vague thought - did someone say one of the bigger retail Technic sets has one too?) I wonder why don't they sell them in a service pack?! Hmmm... (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
I'm certainly glad I picked up two when I did. Without the AC adapter, there's no way I could have setup the webcam at (URL) thing is on 24 hours a day. Oh, and it also has no batteries in it whatsoever, and I haven't had a problem with turning it (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: new pieces (was Re: Wot no RCX power connector?)
 
(...) I've uploaded all 4 pages (each around 150 KB): (URL) for the new bricks - well they are in the upgrade kit ;-) - but my best guess is that they might be in some sort of service pack too for next year - the differential is - but the new ones (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RE: new pieces (was Re: Wot no RCX power connector?)
 
These connectors are also available in kits like #8252 Beach Blaster, where they are used to "plug and play" different suspension/wheel configurations. Reasonably stiff for what they are, and I think they would make good attachments for light (as in (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) Hah. Mine has a power connector. It's sitting on my desk, light as a feather, with no batteries whatsoever. Now, if I could stop tripping over the DC cord... (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  RILYBOT 4 (was Re: show-me training
 
I now have a robot working using the intuitive training principles I described about 6 weeks ago in this thread. This robot will be at Mindfest. Here are the web pages describing what I've done so far: (URL) here is the current NQC program: (URL) (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: new pieces (was Re: Wot no RCX power connector?)
 
(...) Yeah, but until LEGO releases a soldier minifig and a leatherman minifig, I'll never be able to model the Village People! Come on, TLG, where are your priorities? (oops, sorry -- only slightly way off-topic.) - Robert Munafo (URL) LEGO: (...) (27 years ago, 19-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) Another guess - again pure speculation - is tha having an external adapter option made certification more difficult in one of the non-U.S. markets. I believe 1.5, aside from being an update for U.S., is also going to become the (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
Yes, they left it alone... The 1.5 RCX ROM has the same version number as the 1.0 RCX ROM. The firmware file shipped on the 1.5 CD is identical to the 1.0 firmware. Dave Baum (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
The Scout (from the Robotics Discovery System) doesn't have a power connector either. It is quite possible that the decision to remove the power connector from Mindstorms products was made during the development of the Scout. There was only a single (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) Besides the RCX, I've two other sets that can be run off an external ac adapter - #8485 Technic Control Center and DACTA #9751 Control Lab Interface. Both of them come with an external adapter. The Technic Control Center can also be run off (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: new pieces (was Re: Wot no RCX power connector?)
 
(...) -Kekoa (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) In the 1999 catalogue from Commotion (UK), there's a Lego power pack, which is pictured near to the control lab interface and the control centre. They don't specifically say that either of these devices need it (at least, I don't think so), (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  CyberMaster
 
Can anybody tell me what the ACTUAL difference between the Mindstorms RCX and the CyberMaster is? The only thing that I can find is pictures, and they look different. It mentions something about games, and being able to write your own... but isn't (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: CyberMaster
 
(...) The CyberMaster has a lot of potential and in fact can do things the RCX is not able to, like to count the rotations of the two internal motors. The problem of the CyberMaster is to harness it's potential, because the software is all about (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Could somebody use this program?
 
At 07:08 06-10-1999 Wednesday , Michael Lachmann wrote: [...] (...) The firware of the CyberMaster is burned in ROM so you have no way of changing it, and that's also why you can not use the LegOS with it. The firware is a library of routines that (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: CyberMaster
 
(...) The reason is probably that the CyberMaster unit it not as readily available in the US as in Europe/Oceania. I'd say that the Mindstorms unit it probably the more flexible unit, and probably the most interesting to work with. Fredrik (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: new pieces (was Re: Wot no RCX power connector?)
 
(...) I wasn't sure that Kekoa had ever admitted to being amazed, so I had a look over at the links above. Now I know what he is talking about. If this is the potential for "Constructopedia" type books, then there is a very high level of art (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: new pieces (was Re: Wot no RCX power connector?)
 
(...) I wasn't sure that Kekoa had ever admitted to being amazed, so I had a look over at the links above. Now I know what he is talking about. <snip> I assume you are amazed at the new anti-gravity levitating brick at the bottom of picture 3. I (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: new pieces (was Re: Wot no RCX power connector?)
 
At 14:21 20-10-1999 Wednesday , Jeffrey Hazen wrote: [..] (...) Yes, it also pulls me, but I think the 3D animated building instructions of the CyberMaster CD are way more easy to follow. Is that you actually see the parts (smoothly) fitting (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Palm Pilot Control
 
I was considering buying a Handspring Visor (A palm Pilot clone, kinda) and I remembered about the JavaOne Conference with the Palm Pilot controlling the RCX with Jini. I was wondering if this source coding was available or what sites have a basis (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: Palm Pilot Control
 
Hi Clint, Here is one site I know: (URL) The Java one conference web site is : (URL) Kalyan -----Original Message----- From: Clint Rutkas [mailto:cRutkas@techie.com] Sent: Wednesday, October 20, 1999 12:40 AM To: lego-robotics@crynwr.com Subject: (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: new pieces (was Re: Wot no RCX power connector?)
 
(...) I understand this as the four pages are new to you - well saldy these are the only 4 pages that look this way - the rest of the Constructopedia has - if one can call it so - standard instructions. regards Jesper (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) The power adapter that comes with the train sets works fine with RCX. KL (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) I've just bought the Mindstorms RIS from Toys'R'Us in Stoke-on-Trent this morning and there is a special offer on the two expansion sets. Half price if bought with RIS. The one I bought does have an external power connector, but is says (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: CyberMaster
 
Laurentino Martins skrev i meddelandet <4.1.19991020110007....est.pt>... [...] (...) [...] Don't forget that you can use homebrew sensors on the CM too, as long as it is passive, and generates a variable resistance. I have used a LDR (Light (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
May I pose a question for anyone who is in receipt of one of the new "Wot no RCX power connector?" RCX's. Have you opened it up to see if they changed the board layout? If they haven't, then it may be possible to populate the site with the (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Palm Pilot Control
 
Clint Rutkas <lego-robotics@crynwr.com> wrote in message news:19991020043938....ail.com... I was considering buying a Handspring Visor (A palm Pilot clone, kinda) and I remembered about the JavaOne Conference with the Palm Pilot controlling the RCX (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Palm Pilot Control
 
Hey why use the palm pilot? You could use the color gameboy :) I mean it has a IR port on the top. The only problem is the fact that it uses cartridges :( If anyone can make a cartridge, then there is (or at least used to be) a section on (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) I thought since my scanner still is on that these 2 pics might be usefull - but I believe disappointing too :( (URL) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Need Balls!
 
I am coaching a team in the FLL contest. I need a supply of those 5 or 6 nub diameter foam balls -- at least 30. Does anyone have an idea of a source? Is there any similar thing that comes from Nerf? How many balls come with the RoboSports expansion (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
In case anyone needs them, scans of the 1.0 RCX boards are at (URL) . -----Original Message----- From: Jesper Kjaer <jesperkj@vip.cybercity.dk> To: lego-robotics@crynwr.com <lego-robotics@crynwr.com> Date: Wednesday, October 20, 1999 4:53 PM (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
It looks like they have changed the boards fairly significantly. Many parts substitutions -- notable the capacitor farm looks like it has been replaced by a battery backup capacitor. The overall parts count seems to be reduced in more places than (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: Palm Pilot Control
 
(...) Cool! This is what I origianlly designed pbFORTH fro, so you could upload source prom your PalmPilot via the Serial interface to the IR tower... There's even an ANSI forth for the PalmPilot for testing code!!! I for one would LOVE to see this (...) (27 years ago, 20-Oct-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
 
  RE: Wot no RCX power connector?
 
(...) Hmmm, see those big hols at the bottom of the board? Add the three little holes above those? And the big cap in there? I'll bet we could solder a power connector in there if we had to. It almost looks like the holes are for a different kind of (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) Nice :) Could the old RCX beep? - I can't find the speaker on the old board.. regards Jesper (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
I was wondering about the speaker as well. The old RCX definitely can beep, and make a whole host of other sounds. Not being an electronics engineer, I'm was uncertain of my ability to identify the speaker on the 1.0 board. It's not the thing that's (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  RE: Palm Pilot Control
 
Yello... this is my first post. I program the GBC. I actually have developed some code to interface to the Mindstorms. See my websites: www.gbdev.org www.gbdev.org/dpstuff If anyone needs/wants me to test anything, I'd be glad too. (If you know C, (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) It's hidden under the LCD. -Kekoa (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Palm Pilot Control
 
Though it is not nearly as versatile as programing your own RCX/Palm communication interface, there is a program for the Palm (with IR) called OmniRemote. It will let you control the RCX with the Palm TODAY so you can see if you like the idea. I (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  Re: Position Finding/Mapping Update
 
I have now constructed the robot and am beginning to program it. I have no way of getting pictures(yet), so I will get them when I can. If you want more information on the design of the robot, email me at gombos@ne.infi.net Andy (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
Doug Wrote: (...) SNIP (...) SNIP I was thinking about this last night. It would be very easy to build a dummy battery, using a 7809 voltage regulator, diode bridge on the input, and a shell to put it in. My stumbling block last night was finding (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  LEGO commercial on TV
 
I saw a LEGO MindStorms commercial on TV. I think I saw it either on MTV. The commercial has the Intel inside feel to it. Kinda hip, with bouncy music, and a bunch of LEGO robots dancing around. I hope they continue spending some money on (...) (27 years ago, 21-Oct-99, to lugnet.general, lugnet.robotics)
 
  minfest and pyroelectric sensor
 
Hi, For those of you who are going to Mindfest this weekend, does anybody want to see the pyroelectric sensor interface I've made for the RCX? I haven't had the time to make a robot for the sensor, and probably won't before Mindfest is over. It is (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Dr Dobbs Journal planning segment on RCX programming
 
(...) A co-worker just lent me his new copy of Dr. Dobbs Journal (November 1999) which contains the article by Markus Noga called Designing the LegOS Multitasking Operating System. Haven't had the time to read it yet, but I thought I'd mention that (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Dr Dobbs Journal planning segment on RCX programming
 
Anyone have any idea when that'll be online? I'm not real familiar with DDJ's online policies, though I know they have an extensive online collection. -Luis (...) ###...### Profanity is the one language that all programmers understand. -Anonymous (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Dr Dobbs Journal planning segment on RCX programming
 
(...) It doesn't seem to be up there yet, although I didn't have much patience with their web site. (It's (URL) in case you want to try for yourself.) I tried to search for "Lego" and it told me it didn't know what to do with the "L". I'll tell you (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: RIS in Elem Eduction Florida
 
i dont know much about florida geography, but there is a tampa bay home schooling group that uses the RCX. go to (URL) and click on Partners. There are also links from that site to K-5 teachers that have used LEGO. Terry Green from Lincoln, MA has (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Robot lab
 
Yes I would recommend it for young children. So far the youngest ROBOLAB programmer on record is 4 years old (or maybe 3). There are many things in the new ROBOLAB 2.0 (out soon) such as scientific data graphing and analysis [see the pictures in the (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Need Balls!
 
Oh man... I'm coaching a team too. I didn't realize that we were going to have to find our own balls! :) -Ben (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: minfest and pyroelectric sensor
 
(...) Henry, I'd love to see your pyroelectric sensor interface. See you there. Mario (URL) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) You could get a battery adaptor, that is, a device for putting AAA batteries where AA batteries should go. They're available easily here in the UK - Maplins for example. The only irritation I see is that you'll need 6 of them; 5 of which will (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) Ah, that explains those people talking about easily wiping the memory by pulling the AC adapter out - the old RCX lost everything immediately, right? The new one claims to (and seems to, but I haven't timed it) retain its memory for up to a (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: LEGO commercial on TV
 
There is one on in Sydney now, with a lego robot, kinda like a bull-dozer, pushing all the dinner plates off a dinner table. Pretty funny.... I read about this stuff in New Scientist (a magazine) first. I was sold instantly :) It seems that they are (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: CyberMaster
 
At 20:11 20-10-1999 Wednesday , Anders Isaksson wrote: [...] (...) Yes, that's why they are not called Rotation Sensors, they are called Tachometers and work like the counter in your car. They count *distance* and they are very in it, because it's (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) It beeps just before it runs out of juice - sadly my batteries keep running low when the RCX is in off mode. I'm right now working on making a set of dummy batteries/internal 9v AC connection. The bottom end of the RCX would easily allow a (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
I was thinking of using only one at the end (attached to the + where it goes onto the PCB), and running a lead to clip onto the first (attached to the - ). The 4 middle ones can be ignored. Jeff jeffrey.hazen@northmill.net -----Original Message----- (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  RE: Wot no RCX power connector?
 
(...) Ummmm, you could buy 2, put one on either end of the battery compartment ann run a wire between them, right? Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) ---...--- Reply to: rhempel at bmts dot com (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Pneumatics and the RCX -how?
 
I know that some of you use pneumatics for yuor robots. How do you do that? I suppose you use a compressor and a motor to change the valve, but that requires two motors and 2 is all that come with the MindStorms. Yes, I can buy more, but I´d like to (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Pneumatics and the RCX -how?
 
I have been searching for the answer to this one for a while. My intent is to find a supplier who has small electrically operated (solenoid) valves which can be driven by the RCX output(s). I have found one so far, but the valves are very pricy. But (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Palm Pilot
 
I've received a few emails about my Palm Pilot program to control the RCX, so I put up a quick web page about it here: (URL) Kory (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  NELUG at Mindfest update (Good News on our Table Space!!)
 
I just got some good news from Fred Martin. We now have 2 tables! We should not have to worry about not having enough space now. Whew... Plus Fred tells me we have a highly visible spot that should attract attention. Also Set-up starts at 3pm (...) (27 years ago, 21-Oct-99, to lugnet.org.us, lugnet.robotics, lugnet.robotics.events, lugnet.loc.us.ma, lugnet.loc.us.ma.bos, lugnet.loc.us.ct, lugnet.loc.us.vt, lugnet.loc.us.nh, lugnet.loc.us.vt, lugnet.loc.us.ri)
 
  Re: Palm Pilot
 
(...) You must change the picture names so they do not include the space: (URL) end.jpg Or instead you can change the link name like this: (URL) Martins [ mailto:lau@mail.telepac.pt ] [ (URL) ] Neither technology nor efficiency can acquire more time (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) I guess TLG still tries to aim their product at children => Childres build cars => Cars cannot be plugged in and drive at the same time => Remove connector because it is not needed => lower production cost. Or maybe the arrows should be turned (...) (27 years ago, 20-Oct-99, to lugnet.robotics)
 
  FW: O'Reilly book
 
I was pleased to have my back-ordered copy of Jonathan Knudsens O'Reilly Mindstorms book waiting for me when I got home last night. Personally I am good with programming totally lame when it comes to understanding or visualising how mechanical (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Scout brick and IR
 
I have been doing experiments with the Scout brick from the LEGO Robotics Discovery set and have come across a few things that have me scratching my head. Please excuse the length of this post. The Scout can understand two types of messages via it's (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Books
 
*If* I could only buy one MindStorms book, which is better, Dave Baum's or Jonathan Knudsen's? Does anyone have both and can compare them? --The WordMeister Doug Wilcox WordSmith Digital Document Services 403 VFW Drive Rockland, MA 02370 (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Wot no RCX power connector?
 
(...) Only if the RCX was "on" at the time. If the RCX is "off" then power usage is reduced to a trickle, supplying power only to maintain the data in RAM, and in this state the RCX can survive for upwards of a minute or more, even with no batteries (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Books
 
(...) I think the point here is that they're different. You should choose the one that best suits your purposes. I'll be getting both of them. :) - Ben. ---...--- Ben Williamson benw@pobox.com (URL) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Books
 
Can either book be found at major physical bookstores yet? (I know that they are at amazon.com) (...) Joel Shafer joel@connect.net (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  Re: Upcoming _Star Wars_ Mindstorms and Technics Releases
 
Actually, now that stuff is leaking out, its starting to look scarily accurate. Now, where is that Jar Jar minifig, Iza hungry! But it doesn't say anything about the Flash speeder in there so, Im going to wait a little longer on eating that fig. (...) (27 years ago, 21-Oct-99, to lugnet.robotics)
 
  RE: Scout brick and IR
 
(...) Best guess - to appeal to different segments of the market - the scout looks 'easy' to use for people with no computer or programming experience - but they still keep a door open for those of us that have computers and are crazy about (...) (27 years ago, 21-Oct-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR