To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6401 (+100)
  Re: Droid Developer Kit
 
In lugnet.robotics, Dennis Clark writes: <snip> (...) <snip> Has anyone with an RCX and one of these Developer kits programmed their RCX to send all 255 messages to it in "P" mode? I understand it does not have a dedicated IR interface, but perhaps (...) (27 years ago, 17-Aug-99, to lugnet.robotics)
 
  IR remote power
 
I've noted that the remote is as good as a tv or vcr one. Direct line of sight is not required. So why can't the tower work that well? -- Did you check the web site first?: (URL) (27 years ago, 17-Aug-99, to lugnet.robotics)
 
  Re: Droid Developer Kit
 
(...) I tried to play Eric Brok's trick (URL) with the Micro Scout. I put the light source across the rail from the Micro Scout, and run the Keep Alive program. Yes, the motor turns on when the train is passing by. However, since there is only one (...) (27 years ago, 17-Aug-99, to lugnet.robotics)
 
  8480 Space Shuttle (was Re: Gears & Mico Motor (Plus Wired Remote Control!)
 
(...) Well, actually I deliberately left the sets at the store and posted the message in the hope that someone else could benefit from it. As far as I'm concerned, I only need one of each set and I already have a shuttle. Sure it's a great model, (...) (27 years ago, 17-Aug-99, to lugnet.robotics, lugnet.loc.us.ma.bos)
 
  Alternate IR Tower power source
 
I've intended to report a modification to my IR tower for quite a while but hadn't felt it was very important; however, there has been a rash of messages about battery life lately, so its time to report this.... I have converted my IR tower to use a (...) (27 years ago, 17-Aug-99, to lugnet.robotics)
 
  RE: Alternate IR Tower power source
 
(...) Yikes! I did a similar thing. I took a 9v wallwart and used a 9V snap connector from a dead IR remote - the IR led is being used in a secret project... Anyways, the snap connector can be "pressed" against the terminals in the tower using a bit (...) (27 years ago, 17-Aug-99, to lugnet.robotics)
 
  Re: Alternate IR Tower power source
 
Another alternative is the 9v Battery Eliminator from Radio Shack (273-1552). This is a simple 9v wall wort that has 9v snap connectors on it. I have tried this on a number of 9v devices, and it works great. Robert McMahan (...) messages (...) (...) (27 years ago, 18-Aug-99, to lugnet.robotics)
 
  New web pages
 
I have put photos and descriptions of some of my models on the Internet, at: (URL) folks will be most interested in the stuff at the bottom. - Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 18-Aug-99, to lugnet.build, lugnet.robotics)
 
  Re: New web pages
 
(...) Robert, I like your 3 wheeled robot alot. I saw it at The Construction Site and thought it was very cool. The main reason for this post is I love the model at the bottom of your page. The proportions to scale are great and I think it is great. (...) (27 years ago, 18-Aug-99, to lugnet.build, lugnet.robotics)
 
  Re: New web pages
 
Cylinder man is just great. Fun robots also. Bob Fay Robert Munafo <munafo@gcctechNO.SPAMcom> wrote in message news:FGMyIq.2s7@lugnet.com... (...) at: (...) (27 years ago, 18-Aug-99, to lugnet.build, lugnet.robotics)
 
  Re: New web pages
 
(...) Wow! Very groovy! I would never have thought of making a robot like those. Those enlarged Lego pieces are also very awesome! Where on Earth did you get all of those green slopes? Greg "See that spider? Don't mind it, it'll kill ya." Majewski (...) (27 years ago, 18-Aug-99, to lugnet.build, lugnet.robotics)
 
  Droid development kit
 
Hello, I've seen some messages of the droid development kit, could anyone give me an address of a place where i can order one? Greetings, Martijn Joosen. -- Did you check the web site first?: (URL) (27 years ago, 18-Aug-99, to lugnet.robotics)
 
  RE: A quick afterthough on - Ideas for a RIS 2.0 [fischertechnik]
 
Actually, there is a platform that provides an alternative - fischertechnik. See (URL) but first turn down your sound. Click on Computer and then Baukaesten and you will see both Mobile Computers and Industry Robots. The Mobile Computing set is not (...) (27 years ago, 18-Aug-99, to lugnet.robotics)
 
  BluBot - now up on my website
 
Hi all, Just completed my BluBot. In response to challenges that have come up now and then, I have created BluBot. This bot will maneuver around an areana collecting yellow balls. It uses a combination of random roaming, line following, and a nifty (...) (27 years ago, 18-Aug-99, to lugnet.robotics)
 
  Dacta Temperature Sensors
 
I am not too familiar with Mindstorms but had a question if anyone can answer it. Do the DACTA temperature sensors work with the Mindstorm units? I plan on buying a Mindstorm set in the near future and I can get a few of these sensors now. I don't (...) (27 years ago, 18-Aug-99, to lugnet.robotics)
 
  Re: Battle Bots
 
(...) Unfortunately, right now (August 18) both web sites are overloaded, probably because of the tournament. The sites are: (2 URLs) You can probably try both sites again after a week or two. The tournament was telecast on ZDTV (a minor cable (...) (27 years ago, 18-Aug-99, to lugnet.robotics)
 
  Re: New web pages
 
(...) Thank you. Seperate pages -- darn good idea. Okay, I've done that! - Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 18-Aug-99, to lugnet.build, lugnet.robotics)
 
  Re: New web pages
 
(...) The model of the large green 2x2 double-slope used 3 2x4 double 1/3 slopes, ten 2x4 1/3 slopes, and four 2x4 1/3 slopes. All of those (and a lot more) are in the 650-piece Freestyle bucket (apparently only available in the US, unfortunately). (...) (27 years ago, 18-Aug-99, to lugnet.build, lugnet.robotics)
 
  Re: New web pages
 
(...) I can't view your rilybot 3 page, it says (and I quote): The requested URL /lego/rilybot3.html was not found on this server. Ciao! (27 years ago, 18-Aug-99, to lugnet.build, lugnet.robotics)
 
  Re: New web pages
 
(...) You caught it after my daemon uploaded the index page and before it uploaded the rilybot3 page. Try it now! - Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 18-Aug-99, to lugnet.build, lugnet.robotics)
 
  Re: Dacta Temperature Sensors
 
(...) I belive yes. You might want to check out S@H though, since they now appear to sell the same temperature sensor, and probably at a lower price. -Kekoa (27 years ago, 18-Aug-99, to lugnet.robotics)
 
  Re: Dacta Temperature Sensors
 
(...) Yes, they are the same item. -Suz. (27 years ago, 18-Aug-99, to lugnet.robotics)
 
  Re: Dacta Temperature Sensors
 
(...) Functionally they're the same but note that they differ in the length of the attached cable. The Dacta temperature sensor (#9889)has a longish cable as it is meant to work with the Control Lab serial interafce B which is a stationary platform. (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: ideas for a RIS 2.0 - Rechargability
 
(...) This would be nice, but remember that toy companies are one of a few reasons disposable batteries exist. :-) On the subject of rechargability though, has anyone used the new Energizer Ni-MH batteries in the RCX? How do they compair to normal (...) (27 years ago, 18-Aug-99, to lugnet.robotics)
 
  Using motor as sensor
 
This probably came up before, but it may not. The (new type) 9V motor can be connected to a sensor input. If it's set as a light sensor, it will power the motor (low power, but usable). When the motor is stalled, its resistance will raise the sensor (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: Using motor as sensor
 
Eric Brok <brok@fcjsvc.hvu.nl> wrote in message news:FGpJ4w.Hqv@lugnet.com... (...) a (...) thus (...) I don't see how using it as a motor would hurt the sensor input of the RCX, but the motor must have really poor power output. I worry about the (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  RCX/NQC motor stall detection??
 
I've seen some posts on a current sensor apperently built into the cybermaster system, but haven't seen such mentioned relative to the RCX. But when you download with NQC, it reports the current battery voltage (assuming this is the RCX and not the (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  RE: Using motor as sensor
 
(...) Hmm, that probably means that the clamping diode to +5 or GND is missing, and I'll bet its the one to ground. It also implies that the input resistor to the A/D circuit is between the clamping diode and the A/D input. I could be totally wrong (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  A piano player (and a conductor)
 
Months ago Anders Isaksson created a "Lego Brick programmable robot", a simple threaded vehicle that interpretes a "program" made of small bricks on a plate to decide where to go. I transferred this concept to a musical contest. Actually my project (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: A piano player (and a conductor)
 
VERY COOL!!! Thanks for the great details to help spur us on to new creations!!! --Alan P.S. Now I have just the rationale I need for another RCX and rotation sensors. Now if I could just convince my wife..... +---...--- | Alan G. Smith | (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Legocam?
 
Folks, I'm thinking on mounting a video system on my robot. Does anyone have a recommendation for a wireless video cameras? So-called "nanny" cams seem to be available for about $400. Will the Mars Expansion kit be wireless? The red rover set (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  On the subject of cameras
 
I have considerable interest in having a "legocam" option. I have browsed numerous internet sites for such devices and most have one thing in common: They're power hogs. The 2.4GHz more so than the 900MHz ones. They expect wall transformer power. (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: On the subject of cameras
 
(...) Check out SuperCircuits, Inc. They sell cameras and several different transmitters, many of which will run on 12volts or less. And they sell some *tiny* cameras! (The GMLTC is working on mounting one in a train locomotive...) (URL) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  RE: A piano player (and a conductor)
 
I love it! Now if only you could make the conductor flip pages of music... JT -----Original Message----- From: Mario Ferrari [mailto:mario.ferrari@edis.it] Sent: Thursday, August 19, 1999 6:54 AM To: lego-robotics@crynwr.com Subject: A piano player (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: On the subject of cameras
 
From: John Barnes <barnes@sensors.com> (...) There are some very tiny cameras available, some of which have been used in R/C planes. I'd suggest grabbing a copy of "Nuts & Volts" and perusing the ads. Last one I looked at had several outfits selling (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: RCX/NQC motor stall detection??
 
(...) Sadly, it is not available to the NQC user. There is an opcode called "get battery power", but it sends the battery voltage to the PC rather than storing the voltage in a variable. -Kekoa (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  RE: New web pages
 
In the description of the Riley Bot 2 you mentioned that it could only go straight on certain surfaces. I remember seeing on someone's web site a large wheel created out of many small wheels mounted perpendicularly around the diameter. With this (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  4128 Freestyle Bucket (was Re: New web pages)
 
Someone asked me by email what I was talking about when I described a "Freestyle bucket". It's set number 4128, and I got one a couple weeks ago in a small toy store in the northeast US for $21.56 (which was 20% off list price, they were having a (...) (27 years ago, 19-Aug-99, to lugnet.build, lugnet.robotics)
 
  *BLUBOT*
 
dOES ANYONE KNOW THE WEB ADDRESS FOR THE BLUBOT? Thanks -Mike -- Did you check the web site first?: (URL) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: Legocam?
 
Actually X10 has a wireless video sender/receiver and a small color camera that attaches to the unit for $150... Only problem is how to power the thing... Goto (URL) and look at their X-Cam. (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  R/C cameras
 
A short few years back a friend and I has a small business that took airial pictures of houses and property for folks. We used an R/C helicopter, a 35 mm slr camera, and a b/w video camera with a transmitter. The Video camera and transmitter ran on (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: ideas for a RIS 2.0
 
(...) It would be better to implement this via a multiplexor brick (which contains a circuit like this one: (URL) a similar brick that performs a similar function for multiplexing outputs. You could also build a connector plate for multiple touch (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  A practical lead screw
 
I have finally managed to construct a workable lead screw. I used nylon threaded rod obtainable from McMaster-Carr: Part #: 98831A411 2 feet length of 10-32 nylon threaded rod $2.56 www.mcmaster.com I cut this into suitable lengths equivalent to (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  linear wheels (was Re: New web pages)
 
(...) That's a type of linear wheel, which I call an "inverted linear wheel". Yes, it's a good solution, and I have been working on exactly such a design over the last two weeks (currently waiting for parts to arrive from Dacta before I can (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  X10 X-Cam
 
I just got my X10 X-Cam last night, and hacked up a way to pan/tilt it with my Mindstorms. Currently I'm not using the included video transmitter, I just have the camera connected directly to my capture card. It's sure nice to have a camera this (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: X10 X-Cam
 
(...) Lemme rephrase that. I don't recall how to share a touch sensor and a rotation sensor on the same input, and use them both within NQC. --- Chris Osborn FozzTexx Enterprises 707 226 7629 - Voice 2136 Coronado Ave. 707 581 1797 - Fax Napa, CA (...) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: X10 X-Cam
 
Accually, I saw a review on the X-10 camra on ZDtv, and it had a good point, the picture will flicker or be fuzzy if the antennia don't match up. KGB AgEnT #4 OUT AKA Clint Rutkas (URL) you check the web site first?: (URL) (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: *BLUBOT*
 
(...) It's here: (URL) - Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 19-Aug-99, to lugnet.robotics)
 
  Re: RIS 2.0 Ideas
 
Many excellent ideas have been suggested... I would most like to see Lego servos like what we have in remote control. These could use both an input and motor connection with appropriate firmware. <ICS> -- Did you check the web site first?: (URL) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: X10 X-Cam
 
(...) That has nothing to do with the camera, that has to do with the 2.4ghz video transmitter that X10 is including with the camera. The camera itself is *not* wireless and only outputs an NTSC signal through a male RCA connector mounted on the (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  [Off-Topic] Re: X10 X-Cam
 
(...) The amusing bit is that X10 has been doling out the possible uses for this thing one at a time. First it was the wireless camera, then "DVD Anywhere", now "MP3 Anywhere", when there is nothing different but which wires you plug into the back (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Droid Dev. Kit, reprise
 
Well, I've built a small "droid" from it now. And I have to admit, since it is a Technic kit, it was fun. It is only a little smarter than a Technic kit that only has a motor because of its programs (such as they are) and the light detector - but, (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: Droid Dev. Kit, reprise
 
(...) Well, A week or two back, when I was in Jacksonville, I had a nice conversation with a TRU store manager. He pulled up Mindstorms on his CRT and let me watch. Down at the bottom of the screen was a second something listed as 'RIS' (or (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  r/c servos
 
In response to the question about RC servos, I noted, while probing the signals on the I/O ports with a scope, that the motor power settings result in varying duty cycle square waves from 1:7 through 7:1 and finally full on as the parameter value (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: [Off-Topic] Re: X10 X-Cam
 
<SNIP> (...) Actually I believe the software that comes with the "MP3 Anywhere" is something similar to Ampapod (URL) allows you to use the X10 Mouse Remote to control Winamp. Ampapod is strictly 9x/NT though. (...) X10 is the king of marketing (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
I love the idea of controlling an R/C servo with the RCX, but I don't think it is possible with only software. On the other hand, a relatively simple circuit could be made to convert a duty cycle to a R/C servo signal. Is anyone out there interested (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
If the pwm is really being controlled by an 8 bit counter, that might be fine for the servos. The current rcx output has a cycle time of 8mS and uses 1mS increments. If those are the top 3 bits, then the resolution is 5 bits worth or 0.03mS. This (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) It is a software-based PWM. The topic of controlling a servo with the RCX has been discussed before. Generating the pulse stream for a servo would not be too difficult with the RCX, assuming you program the H8 directly using e.g. LegOS or (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) To get rid of the speculation here, the PWM is controlled by a programmable timer that the code in ROM configures to generate an interrupt every 1 ms. Output for each of 8 power levels is stored in a small table of waveforms, with the 1 ms (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: Droid Dev. Kit, reprise
 
Or could it be that new 2 in 2 out screen programmable (blue RCX) RIS? JT -----Original Message----- From: Ray Sanders [mailto:rsanders@gate.net] Sent: Friday, August 20, 1999 6:03 AM To: lego-robotics@crynwr.com Subject: Re: Droid Dev. Kit, reprise (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: X10 X-Cam
 
Don't buy the X-10 system expecting to use it for robotics. Those 2.4Ghz transmitters are directional and therefore are not well suited for the robotics application. Go to Best Buy or shopping.com etc. and buy a 900Mhz transmitter/receiver (actually (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  I/R Strobe/Omnidirectional sender/receiver
 
Greetings all, Looking at some of the new posts like the conductor/piano player has got me to thinking about the multiple RCX interacting scenario. The biggest inefficiency to start with is having to direct the entire RCX toward the other one, have (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: Droid Dev. Kit, reprise
 
(...) They'll probably do what LEGO wants them to do. LEGO appears to be fairly inflexible and uncreative and will probably stick to their normal policy. LEGO's normal policy seems to be to tell the store it has been discontinued and allow the store (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) If all you need to do is generate a pulse of a certain length, why can't you do something like this? Sleep(1); // synchronize with the centisecond timer Fwd(OUT_A, 7); Sleep(1); // 1/100 of a second Off(OUT_A); Sleep(2); // 2/100 of a second (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) I can't understand this. Can you correct your grammar so it is clear what you're saying the average servo needs? - Robert Munafo (URL) LEGO: TC+++(8480) SW++ #+ S-- LS++ Hsp M+ A@ LM++ YB64m IC13 (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) The answer is pretty simple, actually. In order to control a servo, you need to use pulses whose lengths are on the order of 1-2 ms. The more steps you get in that range, the more servo positions you can use. NQC can't produce pulses as short (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  a correction! to r/c servo
 
Sorry about that! The resulting 0.03 mS pulse width increments would result in 5 degree increments in the position of the servo shaft. How about that? JB -- Did you check the web site first?: (URL) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) I think what John was trying to say was that pulse widths between 0.7 ms and 2.0 ms give servo rotations between 0 and 180 degrees. With 45 steps in that range, you can control the servo in 5 degree increments. Seems to me he was approximating (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
okay.. how about this.. avg servo needs.. 60hz pulses.. 1.0ms pulse width = end point 1.5ms pulse width = middle of rotation 2.0ms pulse width = other end point that is the form of the data to the servo. so you need to out put pulses 60 times a (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) That doesn't make sense either. If a single step of 2.0 ms causes 180 degrees of rotation, then how does 45 steps allow you to control it 5 degrees at a time? (...) Are you saying that the servo actually operates in steps of one degree each? (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
Ok, Here's my 2 cents on servos...read to the bottom if you are interested in helping to develop the code for this. The servo takes a 60Hz (approx) pulse width signal between 1 and 2 msec The pulses are fed into a little circuit that generates an (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) OhOh, I've piqued my own interest. I've looked at the H8 hardware manual and the RCX internals. The OC1A triggers every msec, except the stupid routine clears the Free Running Timer every time!!!! So much for using the OC1B, maybe. The minimal (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) Okay! Finally I got it! (-: It sounds to me like servos can't rotate continuously in the same direction. In other words, they're good for steering but not for turning the wheels that make the car go. Is that right? Anyway, having heard that (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) There are multiturn servos for winches in RC sailboats, but they are REALLY expensive. (...) Well don't give up too fast. They ARE useful for steering, or lifting, or grabbing because we can set the limits of motion. This makes things like (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Using RCX with Lego Trains
 
I just picked up the Lego "Railway Express" set (#4561) last night. It comes with a "Toy Transformer" electrical plug (adaptor). The label on the plug says (North American version): Input: 120 VAC 60 Hz 0.12 A Output: 12 VAC 7 VA Would this work as (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) Almost exactly how I'd do it. The problem is what if OCIB must be set to a small value, and the FRT has already passed this value when the OCIA handler sets up OCIB in step 3? This problem is solvable. If the total interval is closer to 1 ms, (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) Let's say a 0.7 ms pulse results in a rotation of 0 degrees. Let's say a 2.0 ms pulse results in a rotation of 180 degrees. If all you had were 0.7 ms pulses and 2.0 ms pulses, you'd be able to choose either 0 degrees or 180 degrees, resulting (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) Exactly. See (URL) examples. These servos have a little disc or cross on top with holes at the edges. The servos can turn the disc only 45 degrees in each direction. They are used for moving flaps or rudders on model airplanes. You bend a 90 (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) Whew! I'm glad I got that much right :-) (...) We could check OC1B and if it's "close" just turn off the motor...as far as the long timer goes, OC1A should always force the output off...on the other hand, the OC1B could be set NO GREATER than (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) In (...) make (...) least (...) Hello, New mindstorm user...been lurking for a while. WRT to servo motion -- it is fairly easy to modify standard servos for continuous motion. $ would put this motor about the same cost as lego so not sure of (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) Thinking about this more, I do not know what I was thinking earlier. Since you are in an ISR, you know can count the number of cycles in the instructions between reading the FRT and enabling the OCIB interrupt, and you can estimate "close" (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: Using RCX with Lego Trains
 
Hello, I have used my RCX to control my Lego train using the wall wart for the train for power. You can run the train off of the bateries but it is pretty pathetic. (I did it once by accident.:)) I set up a simple oval track that used th e light (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: New web pages
 
(...) LOL! I love your expert assitance on the page for the ball-axle connector! Cheers, - jsproat (27 years ago, 21-Aug-99, to lugnet.build, lugnet.robotics)
 
  Motor Speed/Torque Sensor
 
I've developed a circuit that can be used to measure the speed of a powered motor. It works by measuring the voltage generated by the motor during the off period of the PWM. Since the highest power output setting is on all the time, it doesn't work (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  robotic rovers
 
Hello all, I'm trying to construct a rover to make its way around a household environment and avoid obstacles reliably. I'm experimenting with several chassis designs to find one to my liking. (Okay, so I build one design, try it for five minutes, (...) (27 years ago, 22-Aug-99, to lugnet.robotics)
 
  Re: New web pages
 
(...) Yeah! Nothing like those "live-action" demonstrations! :-) Is there such a guy on your demo team known as minimax? -Tom McD. when replying, he was a spamcake hunter from L.A., ruthless, cold, and unrelenting; she was an advertising prima donna (...) (27 years ago, 22-Aug-99, to lugnet.build, lugnet.robotics)
 
  RE: robotic rovers
 
I have been real happy using the KISS (keep it simple sir) principle of design. (URL) is the only robot I have built that I have not un-built since it is very simple and the programming makes it a good wanderer. I tend to hook up new parts to this (...) (27 years ago, 22-Aug-99, to lugnet.robotics)
 
  Re: robotic rovers
 
I'm pretty much inclined to go with KISS too; it's less complicated, with fewer parts to worry about and less that can go wrong. Plus you can always expand on it and modify it easily. Bot 5 looks like a good design, especially if it has stood the (...) (27 years ago, 22-Aug-99, to lugnet.robotics)
 
  RE: robotic rovers
 
A/B steering is the simplest possible (and least accurate) steering mechanism. One motor controls each wheel. Similar to the very first robot you build with the Mindstorms CD. No fancy gearing or other machinations. Usually the robot has trouble (...) (27 years ago, 22-Aug-99, to lugnet.robotics)
 
  Re: robotic rovers
 
I have another LDraw(n) rover that I posted in the (URL) group. Only problem is that it's kind of top-heavy, and the motors don't gear down much. Still, it's another design to compare. Incidentally, has anyone tried to combine a rotation sensor and (...) (27 years ago, 22-Aug-99, to lugnet.robotics)
 
  Cybermaster controlled by Quickbasic for DOS
 
I have just posted some information on cracking the Cybermaster communications with the PC for those of you who want to use a Cybermaster on a DOS machine. Included is a simple program that allows you to initialize the Cybermaster and send commands (...) (27 years ago, 22-Aug-99, to lugnet.robotics)
 
  Help needed with opto-interrupter rotation sensor
 
Hello, I am new to the area of homebrew Lego sensors and electronics. However, I wanted to build my own opto-interrupter based rotation sensor using an emitter dectector pair. I have been trying to setup my circuit like the one proposed by Malcolm (...) (27 years ago, 23-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) That's not the type of stepper motor I'm talking about. I've seen the type you're describing, and they have the advantage that you can drive them with really slow pulses if you want. They're essentially just 3-phase AC motors. The kind of (...) (27 years ago, 23-Aug-99, to lugnet.robotics)
 
  MacNQC in beta test
 
MacNQC is a GUI based version of NQC for the Macintosh. You can read more about it here: (URL) course, you can also find it from the main NQC site: (URL) Baum (27 years ago, 23-Aug-99, to lugnet.robotics, lugnet.robotics.rcx.nqc)
 
  Re: Help needed with opto-interrupter rotation sensor
 
fototaker <fototaker@hevanet.com> wrote in message news:FGw9EE.Dp7@lugnet.com... (...) I've never seen the Radio Shack part but I found this on the Radio Shack page. Infrared Emitter and Detector Pair (276>-<0142) Hints and Tips Faxback Doc. # (...) (27 years ago, 23-Aug-99, to lugnet.robotics)
 
  Re: robotic rovers
 
(...) (URL) is a design that worked well for me (and I still have it together if you want better pictures). I've had it running for up to an hour around my living room without getting caught on anything. alex -- Did you check the web site first?: (...) (27 years ago, 23-Aug-99, to lugnet.robotics)
 
  Re: robotic rovers
 
(...) I'm getting a good deal of inspiration from everybody's links - thanks guys! Alex - great designs. You have a good selection of differential apparatuses (apparati? :) ) on your page. How fast do your rovers go? I've tried several designs of my (...) (27 years ago, 23-Aug-99, to lugnet.robotics)
 
  Re: Help needed with the cross compiler setup for legOS
 
=>From: sjkang <sjkang@ee.kyungpook.ac.kr> =>... =>Please help me how to build the cross compile environment for legOS in =>the Linux! Have you ever built GCC? If not, it's probably useful to run through a native build & install (and make sure it (...) (27 years ago, 23-Aug-99, to lugnet.robotics)
 
  all-LEGO stepper motor (was Re: r/c servos and firmware
 
(...) It looks like I might not be able to do this today. My web hosting service (hostsave.com) stopped providing my web pages sometime in the last 24 hours and I'm not sure how long it will take to get them to fix it. Also, a correction: I meant to (...) (27 years ago, 23-Aug-99, to lugnet.robotics)
 
  Re: robotic rovers
 
I've finished the LDraw of my fourth and most current rover; it can be found at (URL) for anyone who'd like to see. Comments? Suggestions? Flame mail? ;) (27 years ago, 23-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR