To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *28669 (-100)
  Re: SHRIMP building was: Re: High Strength Powered Steerable pivot wheel
 
(...) Yes, something like this: | is a wheel pointed straight, \ and / are wheel turned left or right = is the body Going straight: | | |==| |==| | | Turning left: \ \ |==| |==| /==/ Turning right: / / |==| |==| \ \ Disclaimer: I haven't actually (...) (25 years ago, 23-May-01, to lugnet.robotics)
 
  Re: Will not keep P-Code.....
 
Rmoving every chips except 62256 RAM and 74HC132, and try it again if it works. Besides the memory chip (62256), please also check the 74HC373 (under-neath the 62256 RAM). Patrick Hui (URL) Original Message ----- From: "Kurt Telep" <kt25@drexel.edu> (...) (25 years ago, 22-May-01, to lugnet.robotics.handyboard)
 
  Re: RCX motor pulsing
 
(...) Yes. When you set the power for an output port actually you select the duty cycle of a square wave. The granularity depends on firwmare. With standard firmware you can select between 7 power levels; legOS has 255 levels. bye Bernardo New (...) (25 years ago, 22-May-01, to lugnet.trains, lugnet.robotics)
 
  Re: Lego Camera and legOS
 
(...) IIRC, the identifier chip is different, so it returns a different ID, otheriwse it is a regular QuickCam. Change the driver so it recognizes the different chip, and it should work (at least this is what it seemed to be on the robotics mailing (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
 
  Re: RcxCC Font problem
 
(...) That worked. Thanks a lot. (...) No problem for me. I only use my font in regular style. Marc Klein Marc Klein A Mindstorms fan. (25 years ago, 22-May-01, to lugnet.robotics.rcx.nqc)
 
  Re: Lego Camera and legOS
 
Hi, There are two versions of the Logitech QuickCam Express which use two different sensors and as far as I know, only one of them is supported by the alpha driver for Linux. I think that the Lego Cam (and your camera, maybe)uses the other sensor... (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
 
  Will not keep P-Code.....
 
Well, I recently got a hold of a handyboard from a |friend of mine who swore it was "junk and didnt' work" | After cleaning up some ugly looking solder joints on |the board, it powered right up and began to work |great. Well, when I went to screw it (...) (25 years ago, 22-May-01, to lugnet.robotics.handyboard)
 
  New Version: MacNQC 2.2.3
 
Hi All, I just put up version 2.2.3 of MacNQC. The changes are: * Added a menu to select which program slot the code is to be downloaded into. * Added command in the editor to shift text left or right on tab space. * Fixed a memory corruption (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.nqc)
 
  Re: Wishlist leJOS
 
(...) I didn't think of that, but it might explain why my attemps to use the OP cods failed (they hung the RCX completely dead). Then again, I might have used them wrong... Björn (25 years ago, 22-May-01, to lugnet.robotics.rcx.java)
 
  Re: Lego Camera and legOS
 
Last I checked, the chip which the lego camera uses is unsupported under linux. I wrote up a short discussion of what I knew at the time here: (URL) is even less than I seem to remember knowing but hopefully the link there can be helpful. Luis (...) (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
 
  Re: RcxCC Font problem
 
(...) Thanks! It's been a lot of fun working on it in my spare time lately. I'm glad that a few people have found it worthwhile. (...) I've dug around in the code to try and figure out what is going on here and I think I understand the problem now. (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.nqc)
 
  Re: Lego Camera and legOS
 
In lugnet.robotics.rcx.legos, Kenneth Johansen writes: . (...) AFAIK it is not possible yet. ISTR that the legocam is closely related to the Logitech QuickCam express and the project to develop drivers for the latter (look at (URL) ) will eventually (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
 
  Re: Lego Camera and legOS
 
(...) argg....forgot to start a new thread, hopefully you guys will read it anyways :) kenneth johansen kennethj@stud.cs.uit.no (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
 
  Lego Camera and legOS
 
hi all, my supervisor, recently supplied me with a camera that is part of the "vision command" package. unfortunately (and naturally) it only comes with software for windoze. so i was wondering if theres anyone out there that has managed to use this (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
 
  Dead IR Tower
 
Well, after months of flaky IR comms between my tower and the RCX, I can finally say that the tower has died. :-( I've forgotten who first suggested it, but using a videocamera to see if the IR led is still functional is brilliant! I confirmed that (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx)
 
  Re: Wishlist leJOS
 
(...) There still could be some special rom code that is called when the opcode is called for the standard firmware. Not very likely, but still possible. Andy -- See my Visual Interface for leJOS at (URL) (25 years ago, 22-May-01, to lugnet.robotics.rcx.java)
 
  Re: Transmit Frequency
 
Hello, My cybermaster (the tower) has two crystals 26.540MHz and 26.995MHz. Is your the same? Anybody got crystals with other frequencies? Lars Gertsen - Denmark (...) (25 years ago, 22-May-01, to lugnet.robotics.cybermaster)
 
  Re: SHRIMP building was: Re: High Strength Powered Steerable pivot wheel
 
(...) way I (...) four-wheel (...) 8-wheel (...) You drive all the wheels together in the same direction (first output), and use a motor to steer the front and rear groups in sync (second output). Is this what you mean? Very clever. You cannot steer (...) (25 years ago, 22-May-01, to lugnet.robotics)
 
  R: c++
 
Thank you Pat! I should be able to make it go. I'll tell you the results in a couple of weeks, cause I have to finish another project on lnp first. I still don't understand much the unix community: if version 2.5 is to be patched anyway, why not (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
 
  Re: Wishlist leJOS
 
(...) Remember that Lejos is replacement firmware, the OP codes no longer exist as they are part of the standard firmware. Regards Gordon (25 years ago, 22-May-01, to lugnet.robotics.rcx.java)
 
  Re: RCX motor pulsing
 
I have controlled LEGO trains via the RCX many times. The question is how to control the speed of the train under a finer ganularity then just the native power levels. snip ...this comment has promise! Can you vary the width of the pulse? <The good (...) (25 years ago, 22-May-01, to lugnet.trains, lugnet.robotics)
 
  Re: Wishlist leJOS
 
(...) I think that the datalogging area is just a special limited firmware array, but , IIRC, since it mentions nowhere that you have to remember to keep the datalog size into account. Try using the opcodes, and see what works. Andy -- See my Visual (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.java)
 
  Re: High Strength Powered Steerable pivot wheel
 
(...) Well I feel a total fool, sorry Steven. (Embarrassment tempered by the fact that you can still get them.) (...) Here's the original post about this... (URL) (must remember to switch brain on while at work in future) (25 years ago, 21-May-01, to lugnet.robotics)
 
  SHRIMP building was: Re: High Strength Powered Steerable pivot wheel
 
(...) In the near term, I've opted out of the "steer in place" requirement. That way I go from four outputs to two. With an 8-wheel SHRIMP, I steer like a four-wheel steered (FWS) car does at low speed. Also, I don't have to worry about the friction (...) (25 years ago, 21-May-01, to lugnet.robotics)
 
  Re: Wishlist leJOS
 
(...) It does answer my question, but I was thinking that a feature like that would be more memory efficient. It seems to me (knowing very little of programmimg small devices) that there are special OP codes (looking at Keokea Proudfoot's RCX (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.java)
 
  Re: High Strength Powered Steerable pivot wheel
 
The problem appears to be leverage. I have no exposed shaft at all. But the force while climbing stairs still managed to snap the axle at the pivot point. I was suprised the axle broke and the retainers did not just pop off. A steerable shrimp is a (...) (25 years ago, 21-May-01, to lugnet.robotics)
 
  Re: Hardware Hacking the MicroScout
 
(...) No problem... If you know of anyone that can program in PocketPC let me know... I'm trying to get NQC ported to an ARM version of PocketPC. Dean (...) -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 21-May-01, to lugnet.robotics.microscout)
 
  cvs changes
 
Hi, I checked into the CVS repository some changes today. They include: A) a fix to util/dll-src/Makefile to reference ../../kernel/lnp.c, so a symbolic link or copy is not required. B) small changes to various makefiles to get c++ support working (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.legos)
 
  Re: c++
 
Hi, Sorry that I've been AWOL! Attached is a set of patches you can apply to the 2.5 distribution to clean up most of the make process. You will still have to correctly specify the TOOLPREFIX in Makefile.common, or via the make command line. You can (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.legos)
 
  Re: High Strength Powered Steerable pivot wheel
 
(...) I think that no current set includes them. But it's available as spare part in the Pitsco/DACTAcatalog (US only). (...) This is actually the same solution I was thinking to implement: steerable front and rear wheels and side wheels driven like (...) (25 years ago, 21-May-01, to lugnet.robotics)
 
  Re: High Strength Powered Steerable pivot wheel
 
(...) coming (...) There's no turntable in this set, the middle steering joint is a 40T gear. And the green 8446 crane truck has a black turntable amongst it 573 elements (according to lugnet set reference) Simon PS: What's that about those (...) (25 years ago, 21-May-01, to lugnet.robotics)
 
  Re: High Strength Powered Steerable pivot wheel
 
(...) I don't think there are any current sets which include it. But... You will have noticed all the traffic about the 'classic' re-releases coming this autumn. 8459 (to be renumbered 8464) Front End Loader has one though 270DM might be a bit (...) (25 years ago, 21-May-01, to lugnet.robotics)
 
  Re: High Strength Powered Steerable pivot wheel
 
I'm sorry to hear that, because my design was going to use a single axle. My plan is for an eight wheel drive, four wheel steering shrimp. Last night I successfully prototyped a pneumatic steering system. It doesn't solve your problem, though. It (...) (25 years ago, 21-May-01, to lugnet.robotics)
 
  Re: High Strength Powered Steerable pivot wheel
 
I was unfamiliar with that turntable. I will have to see if I can find some. Anybody know of an esay to find kit that include them? I only need two: Front and rear. The steering is handle mainly by the front and rear with the side wheels driven like (...) (25 years ago, 21-May-01, to lugnet.robotics)
 
  Re: High Strength Powered Steerable pivot wheel
 
(...) Do you need to steer each wheel independently? The only really strong turntable element you can also pass a drive through is the Technic Turntable (2855/2856 on Partsref) but you would need six. The internal teeth would make it easy to drive (...) (25 years ago, 21-May-01, to lugnet.robotics)
 
  High Strength Powered Steerable pivot wheel
 
I am building a shrimp-style rover along the lines of what Mario Ferrari built. I uses 6 powered wheels. A pair on each side in lateral boggies, One in the front on an articulated arm, a rear fixed to the chassis. Problem is coming up with a strong (...) (25 years ago, 21-May-01, to lugnet.robotics)
 
  Re: Hardware Hacking the MicroScout
 
Thanks for the Toshiba pointer. Found the data sheet at: (URL) appears to have 8K masked ROM, and 256 bytes (!) of RAM. It also has a serial port and 6 A/D ports, which I don;t believe are being used in the Microscout. I'm going to look around and (...) (25 years ago, 21-May-01, to lugnet.robotics.microscout)
 
  Re: Wishlist leJOS
 
There's no need to implement this because Java allows you to create an array and store as much data as you want in it. You have a lot more power by using an array over the NQC feature, which I believe is limited to something like 100 numbers. Hope (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.java)
 
  Re: Hardware Hacking the MicroScout
 
(...) If I remember correctly it's a Toshiba processor... IF you can HACK more then 1k of RAM in the thing I'm sure many would be interested... Dean -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (25 years ago, 21-May-01, to lugnet.robotics.microscout)
 
  RcxCC (again)
 
I'm embarassed to admit that I've posted yet another revised version of RcxCC to my website. Version 3.2.9.0 further extends the graphing ability I added in over the course of the two previous revisions. In this release it is possible to display a (...) (25 years ago, 21-May-01, to lugnet.robotics.rcx.nqc)
 
  RcxCC Font problem
 
First, thanks a lot to continue the developpment of RcxCC. Your program is great ! I have a little problem with your program. I made a font for my own purpose (small, readable, all characters different). This font is not display correctly in your (...) (25 years ago, 20-May-01, to lugnet.robotics.rcx.nqc)
 
  Re: Another new RcxCC version
 
hi John, (...) RCXcc / reset worked fine, that's a lot more extended then the orginal RCXcc ! (...) At the moment I'm building such an implementation, the main program is a kind of oscilloscope and the launched application is a controler for a (...) (25 years ago, 20-May-01, to lugnet.robotics.rcx.nqc)
 
  Re: Another new RcxCC version
 
(...) I'm guessing the problem with templates is a registry problem. If you are comfortable with editing your registry you might check for a Templates key under HKEY_CURRENT_USER\So...CC\version 3.2\. If that key exists but it contains no string (...) (25 years ago, 20-May-01, to lugnet.robotics.rcx.nqc)
 
  huip@hkstar.com
 
Hi, I have two question. 1. I received my IR transmitter from you, but I'm not sure how to attach it (in what direction). 2. I also received the Polaroid sonar system. I wonder if there are any more info available about it beside the datasheet which (...) (25 years ago, 21-May-01, to lugnet.robotics.handyboard)
 
  c++
 
Is c++ supported in legOs2.5 ? We've been unable to compile even the demos! (I already posted about that) Please give us a voice! thanks Ciao, Vittorio (25 years ago, 20-May-01, to lugnet.robotics.rcx.legos)
 
  Re: RCX motor pulsing
 
(...) The good news is that the RCX outputs are pulse-width modulated. bye Bernardo New e-mail: dibbe@freestation.it (25 years ago, 19-May-01, to lugnet.trains, lugnet.robotics)
 
  Re: Another new RcxCC version
 
hi John, looks good, but I can't use it yet. The main problem I have is that I can't see my templates. At once I found them, a window 10 pixels win width and 25 pixels in height, and I can't get it bigger. Am I doing something wrong ? Very nice (...) (25 years ago, 19-May-01, to lugnet.robotics.rcx.nqc)
 
  Is the Handy Board compatible with Windows ME?
 
I have a Gateway Performance (933Mhz) using Windows Millenium Edition. The Handy Board works on other computers (work, school, etc) but not with this one. I follow the HyperTerminal steps & get the message: "Unable to open COM1. Please check your (...) (25 years ago, 19-May-01, to lugnet.robotics.handyboard)
 
  Hardware Hacking the MicroScout
 
Has anyone dome any hardware hacking of the MicroScout? I pulled a surplus one apart, to see if there was any potential for hacking. The CPU chip has the following markings: 22576.51A 87C808LM 1681 JAPAN 9916EAI D0029DBA It's in a 28-pin package. (...) (25 years ago, 19-May-01, to lugnet.robotics.microscout)
 
  Trouble loading programs
 
Hi all, I'm new to legos and am having some problems loading programs. I have searched the news pages for my particular error and there are some that are close but not exactly. I hope someone can help because I am currently "dead in the water". Here (...) (25 years ago, 19-May-01, to lugnet.robotics.rcx.legos)
 
  midstorms in dubai, uae
 
are there any mindstorm users in dubai? (26 years ago, 19-May-01, to lugnet.robotics)
 
  Re: RCX motor pulsing
 
I don't use the RCX but I do know know to control a motor. I would picup the power and "pulse" the motor will e.g. 400 Hz, but pulse-wide-modulated. The idea is that the motor gets full power but not all the time meaning thar it has full strenght (...) (26 years ago, 19-May-01, to lugnet.trains, lugnet.robotics)
 
  Re: RCX motor pulsing
 
What kind of train you to use (Lego, Trix, other) ? Although I've no experience, I have the feeling that only a Lego train could be controlled, as far as I know Trix uses AC current and for the other brands I've the feeling all specs are too low. (...) (26 years ago, 19-May-01, to lugnet.trains, lugnet.robotics)
 
  Re: Dead RCX
 
(...) Thanks for the response. I tried bending the tabs to ensure they were making contact with the batteries. That didn't work, so I opened the case and confirmed that the 9V (actually 9.6V) was reaching the voltage regulator. It was, so I know (...) (26 years ago, 19-May-01, to lugnet.robotics.rcx)
 
  RCX 1.0 at Georgia LEGO Outlet store (9709)
 
While visiting the Georgia LEGO Outlet store today I found out that they have a couple cases of the 9709 1.0 RCX ((URL) is the 1.0 RCX with the power jack, nothing else. It is just the RCX, no software, no IR tower, no power pack...just the RCX. (...) (26 years ago, 18-May-01, to lugnet.announce, lugnet.general, lugnet.trains, lugnet.robotics)
 
  Another new RcxCC version
 
Rather than postpone this upload until I'm completely done with the feature, I decided to make it available for anyone interested since I think it is turning out to be very nice. I've just posted version 3.2.7.3 of RcxCC (with the latest source) to (...) (26 years ago, 18-May-01, to lugnet.robotics.rcx.nqc)
 
  RCX motor pulsing
 
Since you guys are talking about this I have a question. I've asked it before and there was no responce. Here it goes: I want to use the RCX to control a single train thru the rails by providing "pulsed" voltage to have fine control over the trains (...) (26 years ago, 18-May-01, to lugnet.trains, lugnet.robotics)
 
  3803 RIS 1.5 Upgrade Kit
 
Hi! I noticed that the 3803 RIS 1.5 Upgrade Kit is availible from S@H. Does anybody know what _bricks_ it contains? I already own the 1.5 version of the RIS but I thought it might be some of the good parts in a low price set :) Thanks! /Tobbe (URL) (26 years ago, 18-May-01, to lugnet.robotics)
 
  Re: Cheshire LEGOFest pictures
 
I got a 4 Way Unit though John, Its very cool, when i get my Models out again i will be going a bit of work with this Thanks John :-) Michael (...) (26 years ago, 18-May-01, to lugnet.loc.uk, lugnet.technic, lugnet.robotics)
 
  Re: gcc hb lib
 
Kai Schlamp writes: > Can somebody tell me what the assembler directive ".follow" means in the > GCC Handyboard Library written by Curt Mills? I can´t find it in the > documentation of the up to date as6811 version 3.0 and as6811 also > doesn´t (...) (26 years ago, 18-May-01, to lugnet.robotics.handyboard)
 
  Re: Cheshire LEGOFest pictures
 
(...) John Barnes has put together some units - you can get in touch with him at barnes@sensors.com Thanks, Jennifer (26 years ago, 18-May-01, to lugnet.loc.uk, lugnet.technic, lugnet.robotics)
 
  Re: Dead RCX
 
(...) Hi Matthias, normally I'd call LEGO service. The only thing I can think of is that maybe the power connection is lost. That shouldn't happen to an unopened RCX, but who knows. The power connection from the batteries to the mainboard is by (...) (26 years ago, 18-May-01, to lugnet.robotics.rcx)
 
  Re: Dead RCX
 
(...) It's completely and utterly dead. Matthias Jetleb VA3-MWJ (26 years ago, 18-May-01, to lugnet.robotics.rcx)
 
  Re: Droid Developer Kit P-Mode
 
Hi, (...) I wrote a NQC program named libvll.nqc. You can transmit vll using RCX. (URL) also wrote a simple Windows program named WinVLL. But you need USB LEGO TOWER contained in RIS2.0, when you use it. (URL) am sorry. This page is written in (...) (26 years ago, 18-May-01, to lugnet.robotics)
 
  Re: Cheshire LEGOFest pictures
 
any chance of marketing this item. any number of us would be willing to pay for it. (...) ps jennifer is cute (26 years ago, 18-May-01, to lugnet.loc.uk, lugnet.technic, lugnet.robotics)
 
  gcc hb lib
 
Hy! Can somebody tell me what the assembler directive ".follow" means in the GCC Handyboard Library written by Curt Mills? I can´t find it in the documentation of the up to date as6811 version 3.0 and as6811 also doesn´t assemble the files with this (...) (26 years ago, 17-May-01, to lugnet.robotics.handyboard)
 
  Re: Lego/RCX IRPD
 
John, I am working on a setup that Rainer Balzerowski and Stephen Edwards havew talked about to allow for up to 15 sensor. My ideal design uses about 7 sensors. Two crossing in the front, Two crossing in the back One pointing to each side and One (...) (26 years ago, 17-May-01, to lugnet.robotics)
 
  Re: Problem with Lejos 1.0.0Beta3
 
Are you sure the port you IR tower is connected to is really com2? You might try connecting to com1, and then just use lejosfirndl . For me, this works - it tries com1, and then downloads. (...) (26 years ago, 17-May-01, to lugnet.robotics.rcx.java)
 
  Re: Dead RCX
 
Completely dead? no response of any kind when you push the ON/OFF button? I ask because if battery power is off for too long, the firmware evaporates and the RCX is pretty non -responsive. But the LCD is not blank. If this is the case, download the (...) (26 years ago, 17-May-01, to lugnet.robotics.rcx)
 
  Re: Lego/RCX IRPD
 
Hi John, Yes, I've got practical experiences with these sharp devices. I've got three of them (GP2D12) and attached them to a little 6wheeled robot. They are "looking" forward. One straight forward, one 45° left, one 45° right. I can avoid obstacles (...) (26 years ago, 17-May-01, to lugnet.robotics)
 
  Re: Lego/RCX IRPD
 
John, Your absolute best bet is the Sharp GP2D12 because it outputs an analog voltage proportional to the distance to a detected object. However, it wants a Vcc of 4.5-5.5V so you'll need to put a regulator on it and use the well-known RCX power (...) (26 years ago, 17-May-01, to lugnet.robotics)
 
  Re: Desktop Theme
 
I know of a few Icon sets found at www.iconfactory.com that are LEGO themes. one is all of the star wars minifigs and the other is blocks and such based loosely on the theme in Microserfs by Douglas Coupland. of course, Icon factory caters to MAC (...) (26 years ago, 17-May-01, to lugnet.robotics)
 
  Lego/RCX IRPD
 
Does anyone have any practical experience using devices like the Sharp IRPD with the RCX? What do you use it for? What sort of range does your application require? What sort of measurement rate is necessary? If you haven't tried one of these things (...) (26 years ago, 17-May-01, to lugnet.robotics)
 
  Re: Floating ponts ??
 
(...) Exceptions to the 0th law: You are manipulating and comparing floating-point values you know are integers with a magnitude less than a million or two. You are manipulating and comparing values you know are integer multiples of some power of (...) (26 years ago, 17-May-01, to lugnet.robotics.rcx.legos)
 
  Re: Floating ponts ??
 
Hi there! (...) 0th law of computer science: NEVER use == on floats; it simply doesn't work as expected. In most cases a value cannot be exactly represented as a float variable; so MOST comparisons for equality WILL fail. (this is NOT an issue of (...) (26 years ago, 17-May-01, to lugnet.robotics.rcx.legos)
 
  Re: generating waves
 
In lugnet.robotics.handyboard, Matthias Weber writes: I think your best bet would be to create an external oscillator that could be controlled using one of the TOC's. I mention the TOC's in case you need to pulse the oscillation (infrared remote (...) (26 years ago, 17-May-01, to lugnet.robotics.handyboard)
 
  Dead RCX
 
Has anyone had an RCX just plain die on them? - Brand new - used manybe 30min total - Fresh batteries - Nothing hooked up to it at the time - Did it's usual beep on startup as my son switched it on and off to listen to the sound I assumed he had (...) (26 years ago, 17-May-01, to lugnet.robotics.rcx)
 
  Re: New RcxCC page
 
(...) 1) Enhanced watch window with counters (for RCX2 & Scout). Watching the Scout now mostly works. I'm still trying to find out how to poll the timers on the Scout. 2) New Remote dialog that is closely modelled after the Lego Remote (works with (...) (26 years ago, 17-May-01, to lugnet.robotics.rcx.nqc)
 
  Re: NiMh batteries
 
You are correct, the NiCd batteries are a dying breed. HOWEVER, NiCds will retain their charge on the shelf whereas NiMh batteries will continually discharge slowly. After a couple of weeks your battery will not have any charge. The best of both (...) (26 years ago, 17-May-01, to lugnet.robotics.handyboard)
 
  NiMh batteries
 
Hello folks, I want to implement 8 Nimh (nickel metal hydride) batteries instead of Nicads on my robot. I have read that these are lighter, have more capacity and don't retain charge memory. The batteries I am looking at are 1200 mAh. Currently it (...) (26 years ago, 17-May-01, to lugnet.robotics.handyboard)
 
  Re: Can the infra red port on the REC be directed?
 
(...) Why not use master-slave principle or time-slots ? (...) I think it will be quit difficult (even with lenses), because the IR transmittors and receivers are chosen to be very omni-directional. With a simple hole you probably loose a lot of (...) (26 years ago, 16-May-01, to lugnet.robotics)
 
  Re: Please call me when you can
 
(...) Kind of like lost mail, wonder where it goes... :-) Andy -- See my Visual Interface for leJOS at (URL) (26 years ago, 16-May-01, to lugnet.robotics)
 
  Re: Please call me when you can
 
(...) Somehow I don't think they got it... TFM -- Coin-Op's For Sale!: (URL) Lego Workshop: (URL) Lego Club: (URL) (26 years ago, 16-May-01, to lugnet.robotics)
 
  Can the infra red port on the REC be directed?
 
Hi everyone. I had an idea for using the RCX's with directional communications. Has anyone been able to direct the infra red by covering the port with bricks and leaving a small hole? Just a thought. I had a quick go but it didnt work. zSoden (26 years ago, 16-May-01, to lugnet.robotics)
 
  Re: Instructions for building own Handyboard
 
Thanks for the advice. I might check out the kits. I'd really like to do it all myself - it helps having a Fry's Electronics about 2 miles from my house, but I understand about the multiple shipping charges adding up. It's also a matter of cost: (...) (26 years ago, 16-May-01, to lugnet.robotics.handyboard)
 
  E3 Mindstorms Mayhem!
 
Well, tonight I'm off to LA, for I shall be playing at the E3 trade show all day tomorrow. E3 is the Electronic Entertainment Expo (e3expo.com), a trade show of mostly video & computer games, plus other toys & fun stuff, including a large presence (...) (26 years ago, 16-May-01, to lugnet.robotics)
 
  Re: lnpd
 
Ah. Those links. I have asked Markus to move those a couple of times but he no longer responds to my emails. I'm afraid that until he does those links will remain in place (and remain quite dead.) Sorry... Luis (...) ---...--- "Nobody ever said that (...) (26 years ago, 16-May-01, to lugnet.robotics.rcx.legos)
 
  Re: ROBOLAB problem.
 
Have you tried changing the power? (...) first (...) about (...) trial (...) second (...) (26 years ago, 16-May-01, to lugnet.robotics)
 
  IR Tower
 
Greetings, Several weeks ago I received a posting mentioning a home built IR tower. Does anyone have information on this? Is a schematic available? Any help would be appreciated. Thanks, in advance, Tim Burt (26 years ago, 16-May-01, to lugnet.robotics)
 
  Re: lnpd
 
(...) This is old news, but I didn't find any answer to it while there are still two such links on (URL) the Doc section, the link to the HOWTO points to (URL) in the File section, the link to the Windows 9x/NT compiler points to (URL) (26 years ago, 16-May-01, to lugnet.robotics.rcx.legos)
 
  Re: RF communication between PC and RCX - anyone tried it?
 
Sorry this actually won't help you, but i replied to say that i was thinking of doing the EXCACT same thing!!! if you find anything could you keep me posted, and i'll perhaps do the same for you? my email: taxihamster@onebox.com (...) (26 years ago, 16-May-01, to lugnet.robotics.tele)
 
  Re: MindScope, watch sensors/vars/timers in a graph
 
hi All, Version 1.0 is released and sources are published. Major improvements: - fast sampling ( 1 channel = 50 Hz / 2 channels = 33 Hz / 3 channels = 23 Hz / 4 channels = 18 Hz) - no spirit.ocx required - some bugs fixed have fun with it ! (...) (...) (26 years ago, 15-May-01, to lugnet.robotics.rcx.nqc)
 
  asking about the changes of sound on the lego dacta software(IMPORTANT AND URGEN
 
i am a student doing a project which might use lego dacta software as my project's heart my name is stanley from Malaysia. i want to know that can lego dacta software communicate with other programming software like VB or C++ programming. because my (...) (26 years ago, 15-May-01, to lugnet.robotics)
 
  Re: Mindstorms at BrickFest2001
 
(...) I won't be able to run any Mindstorms things, but if I drive (which is the current plan) I'll be bringing a copy of Jin Sato's MIBO robotic dog (very cool - check out his site and his book) for display. I think I'll park him at the LDraw table (...) (26 years ago, 15-May-01, to lugnet.robotics, lugnet.events.brickfest)
 
  Desktop Theme
 
Does anyone know of any good LEGO Mindstorm or Technic Desktop themes for both MAC and Windows? I use the Brickdreams and Mindstorms artwork for my backgrounds, but would really like to include sounds (such as the RCX turning on) and icons that (...) (26 years ago, 15-May-01, to lugnet.robotics, lugnet.technic)
 
  Mindstorms at BrickFest2001
 
...I was talking to Christina (the BrickFestMistress) the other day and it seems like we don't have a "champion" for Mindstorms stuff at BrickFest (www.brickfest.org). So anyone who is coming to BrickFest and is interested in stirring up some kind (...) (26 years ago, 15-May-01, to lugnet.robotics, lugnet.events.brickfest)
 
  Climbbot
 
My students recently created a robot as part of their requirements for their Product Design course. You can see the results and notes at: (URL) B. Combs, MS, CIT Associate Professor / Instructional Technologist Ivy Tech Community College of Indiana (26 years ago, 15-May-01, to lugnet.robotics.edu, lugnet.robotics, lugnet.technic)
 
  video of Spring 2001 Robotic Egg Hunt now online
 
In case you missed our live webcast on 29 April 2001, I have put the complete Spring 2001 LEGO My Egg-O Robotic Egg Hunt video online. (URL) site in case www.eecs is down; it's been spotty lately, due to renovations in the machine room] (URL) 8 (...) (26 years ago, 15-May-01, to lugnet.robotics.handyboard)
 
  Fred's book available again
 
Hi everyone, Sorry for the shameless self-promotion, but: my book is in stock at Amazon and Barnes and Noble again. If you'd like to order with me as an affiliate, below are links to the respective companies. Thanks for your patience and interest! (...) (26 years ago, 15-May-01, to lugnet.robotics.handyboard)
 
  ROBOLAB problem.
 
Hi I'm wondering if anybody has seen the following using Robolab v2.?. My son has a program wherethe first thing he does is backup for 50/100's of a second(reverse motors B&C)turn for 25/100's of a second (motor B forward) and then backup for (...) (26 years ago, 15-May-01, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR