 | | Re: Best (disposable) battery for the RCX?
|
|
It's strange that you say alkaline batteries don't "seem to last very long at all". I've been using mine for over a month. You should probably qualify your statement by saying how many minutes or hours you've run the motors on those batteries. (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) All you need is to put a differential between the wheels. If those wheels need to have traction, all you have to do is to apply the force to the differential itself and the differential will distribute the traction for the two wheels like a (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Best (disposable) battery for the RCX?
|
|
Well, I wouldn't really even use the batterires unless I was going to do some robot that had to be moving around. I would just use an AC Adapter for it. Simplistic and cost effective instead of blowing 6 batteries in a few short hours of using the (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Mechanical question
|
|
I've been puzzling over this one, and I still don't really understand it: Why can a bot with tank treads do a turn in place, while a bot with four wheels geared together so that the front and back wheels on each side always move together can not? My (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Best (disposable) battery for the RCX?
|
|
In lugnet.robotics, Jon Shemitz writes: [snip] (...) I use Rayovac Renewal rechargable alcalines myself. I get lots of time on each charge and can use the same cells over and over again for over a year. I get a four pack of AAs for about $6 and (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) Maybe I did not phrase my problem clearly. It's better described in Jon Shemitz's recent post (URL). In my experience, wheels are more efficient than treads. Under the same load, my wheel-based design outrun my tread-based design. However, (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) [snip] (...) You are close here. Tank steering is often called "skid" steering because tank tracks are optimized for traction parallel to direction travelled and have little traction in a tangent direction. A look at the tread pattern will (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
This isn't an answer, but why not just make a three wheeled bot. You can place the third pivot wheel inside the radius of the two outer wheels, and you'll have a bot that turns in place. Most of my bots are of this design. Here is a crude ASCII (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Interactive human-controlled bots
|
|
I haven't tried it myself, but I've heard that you can make your RCX program respond to three of the buttons on the RCX remote control. You can also (if you need more than three commands) use a second RCX as a remote control. I've run across a (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) Have you seen the mars rover turn? If you have the parts for it, you could add a steering mechanism in the front wheels and another for the wheels in the back. Humm... that should make an interesting mechanical project :-) Laurentino Martins [ (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: CyberMaster tracks (was Re: LEGO Lawn-mover)
|
|
The CyberMaster tracks do look cool, but you can build your own tracks out of "standard" LEGO Technic parts (and bigger than "the biggest LEGO has ever built"). See my website: (URL) Haye IBM ADSM Server Development ... Tucson, AZ haye (at) us (dot) (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | RE: Homing with the IR Tower
|
|
(...) The little lift truck in the 8062 Universal set has the same steering mechanism. Just use a standard steeing rack with the steering knuckles on opposite sides of the wheel. Sorry for the inept description, my lids are calling for dinner time.. (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) I don't know the other LEGO tracks, but the CyberMaster tracks confirm everything you said. They look like this (fixed font): | ----| |---- | |---- | | ----| | ----| |---- | |---- | | ----| | ----| |---- | Also, they are deeper in the center (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
I was wondering the same thing until a little while ago, I saw a large (i.e. industrial-sized) remote control vehicle in use by the UK fire service to fight fires in hazardous areas. The vehicle uses solid low- grip rubber tyres and four wheels that (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | RE: CyberMaster tracks (was Re: LEGO Lawn-mover)
|
|
(...) Technic beams in any other colors? ;-) Cheers, Ralph Hempel - P.Eng ---...--- The train stops at the train station, The bus stops at the bus station, So why am I sitting at a work station? ---...--- Reply to: rhempel at bmts dot com ---...--- (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Interactive human-controlled bots
|
|
(...) [snip] Or, you could get the RCX remote control available at S@H and see what kind of stuff that will transmit to your RCX - its got a lot more buttons on it! Or, since you are supposed to be running a robot, you could just program the darn (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | RE: [Rumour] FBI and Mindstorms
|
|
Next thing you know, RCS bricks will be banned on airplanes, too. Singapore Airlines for example already mentiones Furby's in their pre-recorded onboard safety announcements. You are supposed to remove the batteries from your Furby while on board. (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | RE: Interactive human-controlled bots
|
|
The three buttons on the remote control simply send messages 1, 2, and 3. These are the only buttons that send IR codes that can be processed by your RCX program. All the other buttons send codes that get processed directly by the firmware, and will (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Interactive human-controlled bots
|
|
(...) That's the remote control I was talking about. There is only one RCX remote control. Only three of the buttons on the remote control are useable as commands to a running RCX program. All the other buttons either cause the program to stop or (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Interactive human-controlled bots
|
|
Check out the reports on the RoboGladiator event which was held in May 1999 at: (URL) It's everything you want, all done with LEGO! (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Interactive human-controlled bots
|
|
(...) you (...) Check out the description and pictures of the recent "Robogladiator" event: (URL) wasn't there, but it looks like it was fun. The site shows pictures of 6- button controllers made up of two RCXes (not counting at least one to control (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | RE: CyberMaster tracks (was Re: LEGO Lawn-mover)
|
|
Cybermaster has a wider variety of parts than Mindstorms. Except for the unique tracks, with the wheels and one-piece frames for mounting them, these parts can also be found in various other Technic sets. Examples are: - a rubber tipped (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) Add on: Also important in all this is the distance the tracks are apart. The further apart the less friction they have, since the radius is larger. Same happens with wheels. Laurentino Martins [ mailto:lau@mail.telepac.pt ] [ (URL) ] -- Did (...) (27 years ago, 26-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Interactive human-controlled bots
|
|
I have an interactive Human-Controlled program that works with the RCX, my Real Time Control Program. It can control your robot via your keyboard or Joystick. (URL) AgEnT #4 OUT -- Did you check the web site first?: (URL) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Hello, Don't give up on pneumatics just yet. See what you can do with them: (URL) s soh (27 years ago, 27-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | "Dog" built with 2 RCXs and lots of turntables
|
|
I'm looking for the web site that shows the "dog" that someone built with two RCXs and a whole bunch of large turntables. It had one RCX for the head and front legs and another for the back legs, and the RCXs talked to each other via IR messages. It (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | RE: "Dog" built with 2 RCXs and lots of turntables
|
|
I beleive you are looking for Jin Sato's site. It is at: (URL) site is an excellent example of what can be done with Lego and imagination. Rich (URL) Message----- From: news-gateway@lugnet.com [mailto:news-gateway...net.com]On Behalf Of Robert (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
I just bought my first cylinder and pump. Now I have to buy another one. That motor is so cool. Got to build it. Thanks for the page of instructions. Bob Fay rfay@we.mediaone.net The Shop (URL) s soh <cssoh@singnet.com.sg> wrote in message (...) (27 years ago, 27-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: "Dog" built with 2 RCXs and lots of turntables
|
|
Yes, that's it! Thank you very much. I see the reason I couldn't find the site -- I was searching in English. The words I was searching for were the words that had appeared in my head as I was describing the pictures to myself. Silly me! For those (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | RE: CyberMaster tracks (was Re: LEGO Lawn-mover)
|
|
(...) Nice, but where are you supposed to find 500+ each of chain links and conveyor links?! You'd need dozens of service packs... Stuart -- Did you check the web site first?: (URL) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) I'm intrigued too by Joel's challenge. This was the reason for I started my experiments with odometry months ago. The problem is always the same: much more projects in mind than time to carry them out :-) <snip!> (...) motors, (...) are (...) (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
In lugnet.robotics, Soh Chio Siong writes: [snip] (...) [snip] Indeed don't! There is no better way to get great power and speed at the same time then the pneumatics. With a worm gear you can get great power, but not much speed, with the gears you (...) (27 years ago, 27-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) I've built a PC program for the CyberMaster that pools the integrated tachometers continuously and shows the trajectory of the bot in the PC screen. It uses _tracks_, and I've found out that besides one of the tracks runs a bit better than the (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Need treads
|
|
Which current sets include treads? Thanks for any help. (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) My first thought: If you don't connect the tachometers directly to the tracks, but to the separate, unpowered wheels, you don't have to care if the tracks slip or not. My second thought: When the robot turns, there is exactly one "fixed point" (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) that you can see the big air pump, with its spring still attached, is used in the compressor. Has anybody built this robot from the pictures? I always wonder how well the compressor works. Cheers, Hao-yang Wang (27 years ago, 27-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) I built a compressor with the large pump with the spring removed. It worked but it was too slow . It took 3-4 minutes before enough pressure was available to open a big piston just once. The compressor had to be geared very slow to provide (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: legOS and Markus in Forbes
|
|
(...) This is BIG NEWS and GREAT exposure for Markus and friends!!! -- a major business magazine recognizing the pursuits and achievements of adult LEGO fanatics on the net to extend the RCX technology toward greater heights! In May, Forbes also had (...) (27 years ago, 27-Jul-99, to lugnet.robotics, lugnet.robotics.rcx, lugnet.robotics.rcx.legos, lugnet.general, lugnet.publish, lugnet.announce)
|
| |
 | | Re: Pneumatics and Mindstorm
|
|
> I have never tried to send an attachment to the group so > sorry if it does not work. It works fine, but please, don't do it. Just go open a XOOM.com membership ("It's free!"), stuff the image there, and give us the URL. (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) Why is this? The further apart they are, the greater r*cos(theta) is going to be for any given theta. Seems like that would make for more turning resistance, not less. (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) Because the wheel base length shrinks in relation to the turning radius. It is this distance that causes the friction. The further this point is from the imaginary circle that the treads describe, the more perpendicular friction there is. As (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Need treads
|
|
(...) I recently posted a notice to the Robotics forum about the fact that KB Toys is selling the 8414 Mountain Rambler set for about $20 US, down from about $33. You can see a picture of this set at the following location: (URL) set includes a pair (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) I'll try to explain this with an ASCII picture, but I'm make no promises about the quality... Please use a fixed font (as you always should in newsgroups) Legend: #### - Lower part of the track (the part that touches the ground). OOOO - Inner (...) (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: legOS and Markus in Forbes
|
|
It does talk about the " using an open architecture system. " "MindStorms robot developers were creating code in a variety of languages like Visual Basic and C on their PCs and uploading the code to the RCX units. " John A. Donaldson (...) (27 years ago, 27-Jul-99, to lugnet.robotics.rcx.legos, lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
Mario, i am still intrigued by your creative response to posts. Good luck. & may the force be w/u. Michael Aaron (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
FINALLY! some one has described a use for pneumatics! I keep debating on whetjer to buy some, because i don't know what to do w/them. My father is an engineer, but i remodel houses. I just like legos still as an adult. Thanks, & keep up the good (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: legOS and Markus in Forbes
|
|
(...) That's kind of only a tiny mention. I meant that it didn't really talk about it in-depth. That's what's so cool about the new article, IMHO -- it's a first step toward a larger awareness. --Todd (27 years ago, 27-Jul-99, to lugnet.robotics.rcx.legos, lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) That makes sense - thanks! (27 years ago, 27-Jul-99, to lugnet.robotics)
|
| |
 | | Re: legOS and Markus in Forbes
|
|
Yahoo! Maybe we adult lego enthusiasts can finally come out of the closet & say, "were here, we like lego's, GET USED TO IT!!!" : ) Michael Aaron (...) (27 years ago, 28-Jul-99, to lugnet.robotics.rcx.legos, lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
It makes for more. Don't ask me why, it just does. It kind of reminds me of a great old banjo player i know. When i asked him to break down the way he used his picking hand he said, impatiently, "WHAT'S THERE TO SHOW?! EITHER U JUST PICK UP THE DAMN (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
U R My hero (next to my dad). Only problem w/him is that he never explains anything!!! : ) Michael Aaron (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Now at MIT
|
|
(...) One consequence of this is that we will need to remove Suzanne's name temporarily from certain web pages (for example, the AucZILLA and LUGNET homepages) as part of a verbal agreement with Suzanne's advisors at the Lab about "mindshare" and (...) (27 years ago, 28-Jul-99, to lugnet.general, lugnet.robotics, lugnet.admin.general)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Another nice thing about pneumatics is that you can put the heavy compressor anywhere you want, and just run a couple of hoses off to the actual piston. This is useful at the business end of a robot arm, for example, where you want a powerful (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
Jonathan Knudsen <lego-robotics@crynwr.com> wrote in message news:3.0.5.32.199907...net.com... (...) The RCX wants a thermister with 12.2kohms at 25C with a -3.7%/C Temp Coef. This isn't equal to anything I can find. I think it is a 10kohm at 25C (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) Sure. Based on other comments I've received I'm guessing my previous explaination was a little obtuse. (No pun intended... angles, get it.) Ok, let's see if I can explain this without any pretty pictures. It is getting to be time for bed so (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Mechanical question
|
|
(...) [lots snipped . By all means, look at the original message! ;-) ] (...) Beautiful stuff! That's what I call an explanation. "progeeks", indeed... :-)) Thanks, Paul! (Incidentally, you're not using a pseudonym? ;-) Best regards, Martin (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: odometry (was Re: Homing with the IR Tower)
|
|
(...) Yes, 95 ticks are always 95 ticks, but the point is if your robot really *is* in the position where it's expected to be on the floor. The main problem with odometry, as you know well, is that errors accumulate very fast. The unavoidable (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Homing with the IR Tower
|
|
(...) You can add more free wheels to make it very stable. (...) When I approached the Joel's challenge I was worried also about the time to collect the cans. My idea was to develop a reliable navigation system to minimize the time to find the cans. (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) I had exactly the same experience. I used that kind of compressor on my S5 robot many months ago, it's slow and unefficient. The small pumps work much better. Ralph Hempel has a very good double action compressor in his page: (URL) like his (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: odometry (was Re: Homing with the IR Tower)
|
|
At 09:20 28-07-1999 Wednesday , Mario Ferrari wrote: [snip] (...) I've downloaded, printed and read it all some time ago :-) (...) I've used 2 wheels instead of tracks once, and the results where terrible compared with tracks. The problem was that (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
(...) At one time Radio Shack sold 10K thermistors but I have not checked lately. Don't remember their temperature coefficient. I do not know the Mouser source. Pardon me if this is an(*) FAQ but could you let me/us know how to contact Mouser? (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: odometry (was Re: Homing with the IR Tower)
|
|
(...) I see your point. Yes, F1 kind wheels are far from ideal to avoid slippage and get accurate results. The larger but thinner spoked wheels that come with the Minstorm RIS are quite better. The free wheel(s) also must be light and thin and (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: odometry (was Re: Homing with the IR Tower)
|
|
(...) Great source. Just found a source where Johann Borenstein discusses the original 1966 paper and gives links for the full electronic version or a CDROM or a book version. Here is the source: (URL) for the pointer! Ralph M. Deal deal@kzoo.edu -- (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
Ralph M. Deal <lego-robotics@crynwr.com> wrote in message news:Pine.GSO.4.05.9...zoo.edu... (...) Radio Shack still sells the 10K thermistor. Mouser is at www.mouser.com The part is at the following url: (URL) description of the part is on the (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
Mike, You are the man. Thanks for the information. Digi-Key sells two thermistors that match that description. The first is KC003T-ND, for $2.71; it has 1 degree accuracy. The second is KC003A-ND, for $11.50; it has +- .2 degree accuracy. I tried (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Well, ultimately the pneumatic power comes from the motor that drives the compresser. At a given time frame you can only squeeze so much work out of the motor, and pneumatics is no magic. It gives you great power but still not much speed, if (...) (27 years ago, 28-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Broken links (was Re: pneumatics & mindstorms?)
|
|
I can't get these links to work now. Can anyone find the image and post a new link to it? Maybe someone who actually downloaded it as Tim suggested? (...) (27 years ago, 28-Jul-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) After the big piston operates once, how long does it take to recharge the pressure? (...) I did not build a compressor using the large pumps before, only the small pumps, so I believe in your findings. Still I wonder why. The larger pump takes (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) (extra removed) (...) Don't forget, at the actuation end, a pneumatic-based motor should be liquid compatible, something the electric motors have a hard time with. Also, you can run the air lines quite far, so long as you are willing to accept (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Temperature Sensor
|
|
Jonathan Knudsen <lego-robotics@crynwr.com> wrote in message news:3.0.5.32.199907...net.com... (...) You might try a trim pot in place of the 2.2K and set the room temperature to be the correct value. You could later determine the trim pot value (...) (27 years ago, 28-Jul-99, to lugnet.robotics)
|
| |
 | | Toronto lego robot challenge
|
|
Calum and I were talking about this, a copy is also being sent to lugnet.*.*.toronto ---...--- Forwarded message ---...--- Date: Wed, 28 Jul 1999 21:26:00 -0400 From: Calum Thomas Tsang <tsangc@ecf.toronto.edu> Subject: TORONTO: Mindstorms (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Hi, I was just wondering where i could find the small pumps that are used to make the compressors. I would like to find it as a seperate piece so that i do not have to buy a whole box. I got a lot of pneumatics with the set 8462 Tow Truck (available (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Hi Nicolas, You will find the parts in the Offical Lego web(www.lego.com) site thru the catalog link. select the service button and then the technic button. This will show you a list of available parts thru the Shop at home service. the part (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) You know, I think I'm starting to get nervous about this 1.5 business. Let's say they do happen to ship a 1.0->1.5 software compatability upgrade. The first question that comes to my mind is: Is the upgrade reversible or irreversible? Any why (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
Well, I accually would feel the new RIS 1.5 will be just new firmware and software. Then maybe a different color casing (maybe the iMac deal with transparance) then just a new stamp on the case. Maybe a new feature like Proximity detection or a some (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Battery cases + mindstorms?
|
|
I don't have mindstorms (or that large a collection of Technic stuff, hopefully Christmas! ;) ), but I've been looking around, and finding creations that use both a mindstorms and a battery box. What does the battery box run (other than lights that (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: Battery cases + mindstorms?
|
|
(...) Compressors for pneumatic stuff, or (if you're sufficiently mechanically minded to make a good set of switches) you can use the 3 outputs of the RCX purely to switch power around, and have the power supplied from the battery box. Sounds like (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Yes, I guess friction is the answer. 1) The difference in the surface of the pistons between the two kind of pumps is important. I didn't compute the ratio, but imagine can easily be 1:10 or even more. To get that ratio you need to gear down (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) How much did they cost? It's a real pain to get them by any other means... Stuart -- Did you check the web site first?: (URL) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) It has to be reversible from the RCX brick's point of view, since there is no hardware on the RCX to forcibly reprogram its ROM. Perhaps on the PC side it is not reversible, but there is always the uninstall new, reinstall old process, which I (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) [snip] (...) I truly doubt that LEGO in going to create a new OCX. Their strategy was always focused in creating the maximum sowtware with the less work possible. The OCX compatibility between two very different devices like the RCX and (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) sequence (...) only (...) 51.99 FF, that means 7.93 Euros. About 8.40 USD at current exchange rate. The problems is they don't ship abroad. To get them here in Italy I had to send a check in FF and ask them for shipping to a French address (my (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | A RCX 'Beacon'
|
|
Well, I'm not an expert when it comes to small electronics and making them, so I thought I would post this question to this list. After working with the RCX for nearly a year now, I've found a tool/sensor that I would really like to have, but no (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: A RCX 'Beacon'
|
|
(...) Brian, I share your dream. It's a great idea. Surprisingly enough just this morning I wrote an email to Al Thiele asking for the same thing. I'm obsessed by the problem of knowing the robot position. I had some success experimenting odometry, (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Hi all, I actually live in Monaco, south of France and I'm about to place an order to Lego France for some spare parts. I can post orders quite easily and send to US using UPS or DHL as some of my company offices are in SF, California. if anybody is (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) <snip! snip!! snip!!!> (...) They already do this. Doesn't part of the process of downloading new firmware involve sending a five byte sequence of the word LEGO followed by a registered trademark symbol? Technically, they could probably sue (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: A RCX 'Beacon'
|
|
(...) Once, when I had the time to think about it, I started an auto-correction algorithm based only in odometry and map matching. The idea was to memorize a map and at each impact with a wall and try to find if that same area was already hit in the (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Hi, thanks a lot for the info but i have one question. How do you order these parts. It says that you can not curently order them through the internet. Thanks in Advance. Nicolas Gauthier (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) this is something that kinda makes me mad. Why the heck don't the have spare parts avaible world wide all the same. It kinda makes me ticked when I have to find someone who is going to order from france just to get an air tank cause all the (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
Accually, what I wish RIS 1.5 would contain would be Radio instead of IR. I have been trying to design some kind of adapter for my RCX and IR tower to do this so I can use my Real Time Control program to an extreme. I mean, IR, it is only direct (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | mouse-click bug in mindstorms software?
|
|
hi, I wrote a very complex program in the mindstorms software (the stuff that comes with the CD with the kit, and has the little building blocks) that uses a lot of its capabilities. my problem: after a lot of hacking on the program, the mindstorms (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Hi, there are two ways to buys spare parts from the Service catalog: 1) Post the order to Lego France with a check (from a French bank); parts will be delivered within a week ONLY to an address in France (or Principality of Monaco, where I live) 2) (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
I think I'm with Kekoa on this one. TLG have always been very hot on what they consider right & wrong (most of us have read the bit on www.lego.com where they take the time to list what is OK & what is not). They take copyright/patent/trademark (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) You use the part numbers from the web page and then call the Lego Shop at home group in your country. The USA phone numbers are posted in the link (URL) or from the Shop-at-home specials link from the main lugent webpage Have fun ! John (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: mouse-click bug in mindstorms software?
|
|
My response would be to drop the mindstorm software. I hated it cause those red blocks won't let me put 2 in a program unless I use command blocks and even then it ticked me off. Also I would do NQC, GPB, or VB instead, far better than the mindstorm (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | www.legomindstorms.com/press/
|
|
All right, I got the Norwegian image link to work by switching browsers. But I'm still having trouble with the first link. When I download the link (URL) into a file, it contains the following: <HTML> <HEAD> <META HTTP-EQUIV="Refresh" (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Locating your position with the help of fixed beacons (was Re: A RCX 'Beacon')
|
|
(...) The simplest way to do this is to build a device that emits a sweeping light signal, similar to a lighthouse, and a blinking signal synchronized to the sweep. Unlike a lighthouse, you want it to sweep back and forth (otherwise there are (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | MN FIRST Lego League page
|
|
Here is a new LEGO Mindstorms Page. This page is for the Minnesota FIRST LEGO league competition which is for kids ages 9-14 and is part of the larger international FIRST LEGO league program. Probably the interesting thing for this group is the MPEG (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) OK, that's what I thought. But from that, doesn't it follow that this statment would be true?-- It is possible to write replacement firmware which, when downloaded and executed, still allows new application code but prevents the downloading of (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|
| |
 | | Re: RIS version 1.5 coming this fall
|
|
(...) That is true except for removing the firmware by removing the batteries. Since the only alterable storage is powered by the batteries, there can never be permanent changes to the brick that survive a hard power-off. (...) The ROM is in the CPU (...) (27 years ago, 29-Jul-99, to lugnet.robotics)
|