 | | legOS-0.1.7 released
|
|
Hello, legOS is an embedded OS for the LEGO Mindstorms RCX. It can be programmed in C, assembler, and some language elements of C++. Preemptive multitasking, access to all 32k RAM and low-level hardware control are some of its most prominent (...) (28 years ago, 19-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.legos)
|
| |
 | | Re: Mindstorms vs. Cybermaster
|
|
(...) The programming environment of the RCX is more powerful, starting by the fact that you can replace the original firmware. Using the standard firmware, the RCX have about 10 times more memory than the CyberMaster. With the RCX you can also (...) (28 years ago, 19-Mar-99, to lugnet.robotics)
|
| |
 | | Teaching with Mindstorms
|
|
I'm new here. Is anyone using Mindstorms as a learning tool for junior high or high school students? Does TLG sell Mindstorms in educational/school packages? (28 years ago, 21-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Teaching with Mindstorms
|
|
(...) Dacta (Lego's educational branch) sells a number of Mindstorms products, including Robolab - a programming environment that's significantly better than the normal Mindstorms environment. They also have a couple of RCX based sets aimed (...) (28 years ago, 21-Mar-99, to lugnet.robotics)
|
| |
 | | Re: what is NRZ ???
|
|
"Erling :O)" writes: => when you write: => The IR protocol associated with sending a "message" to the RCX is=20 => prettysimple. Bit encoding is 2400 baud, NRZ, 1 start, 8 data, odd = => parity, 1 => stop bit. A '0' is coded as a 417us pulse of (...) (28 years ago, 22-Mar-99, to lugnet.robotics)
|
| |
 | | what is NRZ ??? (fwd)
|
|
----- Forwarded message from Erling :O) ----- From: "Erling :O)" <evo@ruc.dk> Subject: what is NRZ ??? Date: Mon, 22 Mar 1999 12:29:36 +0100 when you write: The IR protocol associated with sending a "message" to the RCX is prettysimple. Bit encoding (...) (28 years ago, 22-Mar-99, to lugnet.robotics)
|
| |
 | | Robolab in Canada Re: Teaching with Mindstorms
|
|
Hello: Does anyone know where Robolab can be purchased in Canada? (...) [snip] (...) -- Did you check the web site first?: (URL) (28 years ago, 22-Mar-99, to lugnet.robotics)
|
| |
 | | Using Robolab software with Mindstorms
|
|
I have a Lego Mindstorms set and am interested in a more powerful GRAPHICAL programming environment (I am familiar with language CODING options such as NQC and VB). Can I order JUST the RoboLab software (Lego part no. 2000050 I believe)? Is there (...) (28 years ago, 22-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Using Robolab software with Mindstorms
|
|
Thanks, Sean. That helps a lot. -----Original Message----- From: Sean S. Dunten <Sean.S.Dunten@Dartmouth.EDU> To: jclewis@time-and-money.com <jclewis@time-and-money.com> Date: Monday, March 22, 1999 12:12 PM Subject: re: Using Robolab software with (...) (28 years ago, 22-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Using Robolab software with Mindstorms
|
|
Yes you can order the Robolab from Dacta. It sells for $25.00 for the software and if you want the book that goes with it and takes you thur the software it is $50.00. I am using for mindstorms for my son's home schooling and it is great much better (...) (28 years ago, 22-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Robolab in Canada Re: Teaching with Mindstorms
|
|
There is 2 distributors in Canada that I know of. (...) -- Did you check the web site first?: (URL) (28 years ago, 23-Mar-99, to lugnet.robotics)
|
| |
 | | Re: PUTS MONEY INTO YOUR POCKET!
|
|
tangelo@indiasite.com writes: > E MAIL KING AND ASSOCIATES > PUTS MONEY INTO YOUR POCKET!! Bastards. Okay, I'm going into 1/4-moderated mode. The first time you send mail to the list, the mail will go to me for moderation. Subsequent mails will go (...) (28 years ago, 23-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Mindstorms: Use of Far Mode on IR Transmitter
|
|
Far mode allows you to download or control RCX via suplemental software (NCQ). The IR range can be boosted a bit by reflecting off a white surface (ceilings or walls), I think Radio Shack has a remote control range booster. This should be able to (...) (28 years ago, 23-Mar-99, to lugnet.robotics)
|
| |
 | | RCX IRPD - Kits being made
|
|
Well, I think the initial analysis is in, the RCX IRPD works on at least three Mindstorms bricks! For those of you who can't leave "well enough" alone, read on for a directionally sensitive IRPD for the RCX For those of you who wanted me to put (...) (28 years ago, 23-Mar-99, to lugnet.robotics)
|
| |
 | | new products
|
|
www.legomindstorms.com has got prices and pictures of various new items - most of which have already been discussed here. They are to be available "for the 1999 holiday season"... which means when?! (Easter?) For anyone who may be interested, here (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | new crown gear
|
|
Go to (URL) click for the full size view of the L-3GO robot. It will reveal a new type of crown gear. Eric Brok Visit LEGO ON MY MIND: (URL) Control section: (URL) section: (URL) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | Re: new products
|
|
S. Crawshaw wrote in message ... (...) I doubt it will even be *possible* to connect a second motor (see my previous post). (...) Let's hope it will have something extra to regular cams for the steep LEGO price. (...) I ordered it immediately from (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | Re: new crown gear
|
|
Eric Brok wrote in message ... (...) That should be: Go to (URL) LEGO Mindstorms photos from the menu* and THEN click for the full size view of the L-3GO robot. It will reveal a new type of crown gear. (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | Re: lego turn table/list seems to hve slowed down
|
|
In article <003401be75a3$576358...0@u7x9h8>, billyd <billyd@bcn.net> writes (...) Yes, the volume has lessened considerably. (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | Re: lego turn table/list seems to hve slowed down
|
|
Have you used the turntable? I have been trying to build a turntable base for my digital camera (for panoramic shots) but have been having a hard time trying to get a stable base that rotates smoothly on a single shaft. cheers, rob cairns (...) -- (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | Students, Teachers: spare 5 minutes please
|
|
Fellow-researchers and I are working on using Mindstorms (referring the entire range of programmable LEGO products) for teaching robotics in school. The work would be published at an IEEE conference. We would like to ask students and teachers to (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | RE: new crown gear
|
|
(...) (URL) Brok -- Did you check the web site first?: (URL) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | RE: new crown gear
|
|
# From: brok@fcjsvc.hvu.nl # Sent: 24 March 1999 13:50 # To: lego-robotics@crynwr.com # Subject: Re: new crown gear # ---...--- # Go to (URL) *choose LEGO Mindstorms photos from the menu* # and THEN click for the full size view of the L-3GO robot. # (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | RE: new crown gear
|
|
(...) It is N. Droid Development Kit. It is down at the bottom of the robot. - Tom (...) -- Did you check the web site first?: (URL) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | UK bargain
|
|
Argos are currently selling one of the ZNAP kits (I forget the number - the one that is a helicopter / dinosaur!) for under UKP 13 --- which contains a (RIS-style) motor, battery box (useful for testing) and a couple of flexible axles... Stuart -- (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | Re: new crown gear
|
|
From: Eric Brok <brok@fcjsvc.hvu.nl> (...) The new gear looks very cool. It looks like the 16t gear, but it appears that it can be used as a crown gear or a normal gear. The new mini-sets could make for interesting desktoys at work (something that I (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | Re: new crown gear
|
|
I've been noticing lately that some of the more interesting Technic parts appearing on the ThrowBots are starting to show up in other Lego technic models. The one I see appearing the most often is the hi-tech looking beam that is seen in white and (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | LEGO Image Quality - was Crown Gear
|
|
(...) Right you are, and the following link shows a beam similar to the new race car set (which looks kinda lame) (URL) of the new elements are VERY specialized indeed, but I bet it's not long before some of us come up with interesting uses for (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | Re: LEGO Image Quality - was Crown Gear
|
|
(...) There's another Throw Bot piece that I've seen showing up on the newer Technic models. The first one that I noticed it on was that new green crane truck. I don't have a catalog handy so I'm not certain about the model number. It's a connector (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | Re: what is NRZ ???
|
|
In article <004701be7630$4d2dfd...@p200mmx>, Michel Verhagen <mive@xs4all.nl> writes (...) As a graduate of Manchester University whose viva was conducted by Prof Fred "I invented Baby and the Williams Store" Williams I can bore you rigid with (...) (28 years ago, 24-Mar-99, to lugnet.robotics)
|
| |
 | | 3-wire converter for homebrew sensors
|
|
Home-brew sensor fans - I have developed a converter brick to ease the job of attaching powered sensors to the RCX. The brick converts the RCX sensor interface to a standard three wire interface (+5, ground, and input voltage.) For more info go to (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: lego turn table/list seems to hve slowed down
|
|
because robkc said, (...) for my digital camera (for panoramic shots) but have been having a hard time trying to get a stable base that rotates smoothly on a single shaft. I had to reply with: I used the same turntable for my digital cambot... Got (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Links on Mindstorms in Education
|
|
For those interested here is a list of links on Mindstorms in Education that I compiled from my bookmarks as a request. Links are in no special order and some sites (not links) are mentioned twice. I just checked the links, so they should all be (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
(...) I wonder if you have looked at the simple method for connecting sensors to a RCX on my web page? It really only takes 6 diodes and a capacitor to create a powered sensor interface. Add a opamp if you need gain. This work was originally (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
(...) [snip] (...) Ahh, but the stipulated purpose for Pete's sensor brick is that it gives a _linear_ response that isn't corrupted by the non-linear diode drop caused by currents that are often less than 2ma and perhaps not past the "knee" region (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Polarity Switch = Pressure Switch
|
|
Hi All, Just got my first Technic Polarity Switch and quickly put together a Pressure Switch for Pneumatics. Check out: (URL) and let me know what you think... Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
(...) It is a heck of a lot of complexity for a little added linearity. If you look at the plots on my general purpose interface section; the simple resistor interface is pretty linear. I think most of the nonlinearity in the powered version is due (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | multi-device output controller
|
|
I've been considering various ways to control more than three output devices with only the three ports and came up with the following idea. I don't have the electrical design knowledge to implement, so if this idea sounds good, I'd like to (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
I have not tried pneumatics yet. I know where I will look when I try them out. This is another neat clean working device. Nice work! Bob Fay rfay@we.mediaone.net The Shop (URL) Hempel <rhempel@bmts.com> wrote in message (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) Heck, I'd love to try some pneumatics, but you can't get a storage tank anywhere these days can you? All of the cool Technic kits are discontinued, no subs, (and while I'm whining) no shuttles, no tracked vehicles, only Throwbots and (...) (28 years ago, 25-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) 8462 comes with two of them, and is available from Lego S@H. I'd like to see reissues of the construction vehicles as well. alex -- Did you check the web site first?: (URL) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
Dennis, Thanks for your encouragement. The angle sensor connected straight to the RCX is non-linear because it is in series with another resistor located inside the RCX. During a sense operation, the RCX drives the sensor input from a 10K resistor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors
|
|
(...) As for the diode vs FET, the package used for surface mount is going to be the same so there is no size penalty. The only thing I might change is the regulator, on battery powered equipment I would tend to a DC to DC converter like Motorola's (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
What about a real time circuit that routed the output power to one of eight output ports depending on the PWM. That way it only takes one output port on the RCX and up to three (out of 24) motors could be running at the same time. (...) like (...) (...) (28 years ago, 25-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Joel Shafer ----- Date: Thu, 25 Mar 1999 13:43:33 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller What about a real time circuit that routed the output power to one of eight output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: 3-wire converter for homebrew sensors (fwd)
|
|
----- Forwarded message from Pete Sevcik ----- Date: Thu, 25 Mar 1999 21:00:13 -0600 From: Pete Sevcik <sevcik@flash.net> Subject: Re: 3-wire converter for homebrew sensors The angle sensor connected straight to the RCX is non-linear because it is (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
How well does this work? Contrast with: (URL) on (URL) I got from lu, and which seems to require a fair bit of fiddling to get it to regulate correctly. (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | RE: Polarity Switch = Pressure Switch
|
|
(...) Mine required no tuning at all, if that's what you mean. I tried a similar configuration to lu's and found that the throw was difficult to get right. I don't like the overall size of my regulator, but it works like a champ! Cheers, Ralph (...) (28 years ago, 26-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
(...) [snip] (...) [snip] Ha! I'm one up on ya both. Run a tight loop and find out how fast the RCX can cycle the motors on and off, time it, and send a package a serial message at whatever the fastest BAUD rate is to control a max of N motors with (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Dennis Clark ----- From: "Dennis Clark" <dlc@verinet.com> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 15:27:53 GMT Ha! I'm one up on ya both. Run a tight loop and find out how fast the RCX (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) And where are you getting motor drive power from? I assume you want the selected motor to run at full power, not at 1/8, 1/4, etc. I'm afraid you're still stuck consuming the extra output for power unless you use a separate power source. (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) With a seperate battery box (from 8735 for instance) you could power the output full time. In this case you'd probably want to map it to something like this: off - off 1 - output 1 fwd 2 - output 1 rev 3 - output 2 fwd 4 - output 2 rev 5 - (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 11:26:31 -0500 How about an RCX to RS232 connection to use off the shelf (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
Hi Bill, ----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 11:26:31 -0500 I like the ide that you have but like you, I am not a (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Jim Choate ----- From: Jim Choate <ravage@ssz.com> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 10:34:22 -0600 (CST) It's actualy pretty easy. Take the analog RCX output, integrate, S&H, A/D, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
Has anyone tried out the Muscle Wire or electronic pistons from this site? Seems like a good alternative to pneumatics. (...) -- Did you check the web site first?: (URL) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
Cool. You can also add things like the following: 1. Serial LCD display 2. GPS devices 3. additional infrared send/recieve 4. ANY PC project that is serial port connected! I like the idea of multiple serial channels; this means that you can talk to (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) There are 8 levels of PWM, so fwd/rev for 4 devices is possible. I originally wanted a separate power input to allow a full 8 levels for each device. This would allow the controller to operate ANY device designed for the RCX ports and not (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
There is no need to waste PWM levels on reverse. You can set the RCX motor output to reverse speeds as well, giving you 7 outputs (fwd and rvs) instead of 3 1/2. You need a bridge rectifier anyway; you might as well exploit it to indicate direction. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Muscle wire and alternatives
|
|
----- Forwarded message from Joel Shafer ----- Date: Fri, 26 Mar 1999 11:12:57 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller (fwd) Has anyone tried out the Muscle Wire or electronic pistons from this site? (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 12:33:18 -0500 OK now the details. 6. Send to a MAX232 devices and wallah, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
(...) [snip] (...) Dunno, I haven't looked yet, I just came up with the idea. (...) Because I felt like it? I've seen it written both ways. [snip] (...) Nope. 0 (speed) means off, no matter what direction you are going, therefore: 0= forward, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Stepper motor design
|
|
----- Forwarded message from Wes Matchett ----- From: Wes Matchett <wes@augustschell.com> Subject: Re: multi-device output controller Date: Fri, 26 Mar 1999 17:34:25 GMT Now that I have brought up that topic, anyone know how to drive a stepper motor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
In my example the RCX output was just used to tell this mythical board which output to drive. Power for the output came from a battery box, always set to on. The RCX can't set direction on the battery box (at least not trivially). alex (...) -- Did (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) Are you sure? I wasn't, so I went looking. The NQC docs seem to imply 7 powers levels plus off. Which, technically, is 8 levels of PWM, but if you use all of them, a motor is running at all times. That is fine if you use another motor output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
Right. That is why you cannot use all 8 power levels. The polarity reversal that I am talking about is on the controlling (and only) output. I am already assuming, at this point, that drive power is stuck on as with your external battery box. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) I don't know how NQC drives the ports, but both rcxcc and the RIS software have separate controls for on/off and power level. I just tested setting all 8 power settings - motors operates for all 8. -Wes (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Stepper motor design
|
|
(...) It realy depends on what form of stepper motor you are using and how the coils are wired up. if you can arange it as two sets of coils you could drive it by hooking one motor output up to one pair of coils and the second motor output up to the (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
Thanks for checking this out. This is important to know. I assume, then, that the duty cycles are 1/8 through 8/8 as well as off, which would be 0/8. Can anybody verify this (with a scope or something)? I have long wondered whether the duty cycles (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
How about an RCX to RS232 connection to use off the shelf components? Check out this link. (URL) sells a simple serial servo contol that services up to 8 motors via an rs232 port ($49.95). I have seen a simple version adapted for a Palm Pilot for (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | External Power Port Problem..?
|
|
Esteemed Colleagues, I have two RCXs, both of which have stopped responding to power applied to the external power port. With batteries, they function correctly; with a 9.6v Lithium Ion battery pack attached to the external port, nothing. This has (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | External Power Port Problem..? (fwd)
|
|
----- Forwarded message from Issac Merkle ----- From: "Issac Merkle" <the_gaff@hotmail.com> Subject: External Power Port Problem..? Date: Fri, 26 Mar 1999 06:08:01 PST I have two RCXs, both of which have stopped responding to power applied to the (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Why do it? Was: multi-device output controller
|
|
(...) I have checked this out, and if you use the standard RCX firmware (or other firmware that uses the RCX ROM, then you get the waveforms you are talking about at 125Hz 1/(1ms x 8). You also get polarity information - oh no, I've said too much. (...) (28 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: External Power Port Problem..?
|
|
(...) Ummm, It's not clear from your post, and I'm sure you have tried this, but have you tried a different adaptor? I tried to drive the RCX from a supposedly 9V wallwart, and it didn't work. The I used my lab power supply and started cranking it (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Why do it? Was: multi-device output controller
|
|
Ralph, Thanks for reigning in the rabbit chase! As the originator of this thread I'd like to respond to the 'why'... I keep running out of ports on my creations. I see 5 or 6 as a practical limit. My criteria for a solution: 1. Entirely compliant (...) (28 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: Why do it? Was: multi-device output controller
|
|
I think that the solution should also be flexible enough to allow the power to be plugged into either an RCX output port or a battery pack. That way if you didn't want to lug around another battery pack, or if you didn't want to use up another (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Why do it? Was: multi-device output controller
|
|
My original message described the controller with two inputs, one for device selection and one for device power. This could easily be connected to whatever power source the user desires. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Muscle wire and alternatives
|
|
I have connected nitinol to Lego and it can melt the ABS plastic...be careful. Rich (URL) Message----- From: Jim Choate [mailto:ravage@EINST...N.ssz.com] Sent: Friday, March 26, 1999 11:36 AM To: lego-robotics@crynwr.com Subject: Muscle wire and (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Why do it? Was: multi-device output controller
|
|
(...) Measuring PWM is not difficult, but it would involve a micro (PIC12C508 anyone?) dedicated to the task and then you would have to get it to drive the RCX, which means motor drivers, etc. If you are willing to spend $50 and LOTS of time, then (...) (28 years ago, 27-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | Why do it? Was: multi-device output controller (fwd)
|
|
----- Forwarded message from Ralph Hempel ----- From: "Ralph Hempel" <rhempel@bmts.com> Subject: Why do it? Was: multi-device output controller Date: Fri, 26 Mar 1999 22:17:57 GMT With all of the talk about RS232 converters, and PWM decoders, why (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: LEGO 9V battery box as project container
|
|
(...) Can anyone guess how long a 9 volt battery power supply like this will last compared to 6 AA batteries? This does seem like a good small power solution and project box. <ICS> -- Did you check the web site first?: (URL) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Why do it? Was: multi-device output controller (fwd)
|
|
(...) Hmmm, the RCX tower is a pretty effective RS232 converter...and you will still need to write special software for the RS232 convertor's interface to the PC. Like I said, its cheaper and quicker to buy a second RCX from Pitsco... Cheers, Ralph (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Why do it? Was: multi-device output controller (fwd)
|
|
----- Forwarded message from Ralph Hempel ----- Subject: RE: Why do it? Was: multi-device output controller (fwd) Date: Sat, 27 Mar 1999 02:17:09 GMT (...) Hmmm, the RCX tower is a pretty effective RS232 converter...and you will still need to write (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) Good job, Ralph! The most compact solution seen up to now for a pneumatic switch. Mario (28 years ago, 27-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Angle Sensor
|
|
Hi, Can someone tell me how the angle sensor works? Is it giving a RAW value back, or maybe even a real angle (between 0 and xxx, with step 1)? Where can I get the angle sensor in Europe (The Netherlands)? Thanks in advance... Michel -- Did you (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
(...) The Lego rotation sensor counts each rotation in 16 steps starting from 1 (no. # 2 to 17 for the first full rotation). If the rotation goes backwards the count is negative (no. # 0 to -15 for the first full backward rotation). The count is (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
One of the best suggestions (maybe from Ralph Hempel??) that I have seen for this sensor is to gear it up (down?) to get the desired rotational resolution. -Rob Doucette. Franz-Michael S. Mellbin wrote in message ... (...) (no. (...) 1 + (...) that (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Angle Sensor
|
|
(...) Nope, wasn't me...I'll bet the fancy LEGO milling machine does something like it though... Maybe I should buy a rotation sennsor first :-) Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) ---...--- Reply (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
Well, then I guess I need to build my own rotation sensor using a "Potmeter" (variable resistor) because I need a real angle, actually I need an angle per time value. Is this is possible? I saw something about this on a website in the mindstorms (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Light Sensor Non Destructive Mods
|
|
Hi All, I've just added a new page to my website that describes a non-destructive mod to the light sensor that actually allows it to read ambient light! (URL) The range is <10 for a dark box and >90 for a halogen lamp about 6 feet away. It's really (...) (28 years ago, 28-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | Re: Angle Sensor
|
|
(...) So long as your software remembers to count the revolutions, it's surely very simple to gear the Lego sensor to get a real angle... however for your idea below, you might need much too much gearing! (...) You shouldn't need fuzzy logic to do (...) (28 years ago, 28-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Angle Sensor
|
|
(...) Oh Oh, time to get on the flame suit. I agree with Stuart. Fuzzy logic was one of those fads that was to be applied to ALL control systems. The problem is that many control system problems are well understood and solutions are already in (...) (28 years ago, 28-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
In article <000e01be788c$3c95fe...@p200mmx>, Michel Verhagen <mive@xs4all.nl> writes (...) Someone posted a URL of a balancing machine recently which used fuzzy logic. Try deja news. (28 years ago, 28-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
Your missing one very important fact here: With the equations you gave, the pole can't be a variable size, can it? Anyway, of course all problems solved with fuzzy logic can be solved using "normal" equations, but I'm a student and I'm now following (...) (28 years ago, 28-Mar-99, to lugnet.robotics)
|
| |
 | | NQC tutorial available
|
|
In my opinion NQC is the easiest way to program the Lego Robots. But people that never programmed before seem to think it is difficult (maybe because it sounds like C). So I decided to write an extensive tutorial on how to use NQC. The tutorial does (...) (28 years ago, 29-Mar-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
|
| |
 | | Re: LEGO 9V battery box as project container
|
|
I've already built a PIC based controller into one of these and it almost has as much functionality as an RCX, 3 outputs and 3 inputs [1], in a much smaller space! Of course, using all the ports simulaneously does mean using a lot of 1x2 conducting (...) (28 years ago, 29-Mar-99, to lugnet.robotics)
|
| |
 | | Re: NQC tutorial available
|
|
(...) Mark, I use your NQCCC exclusively to program my RCX. Your code templates and help system (especially the last edition!) are superb. I like your setup because it integrates all the necessary stuff right there and the help files are pretty good (...) (28 years ago, 29-Mar-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
|
| |
 | | Uploading *.prg To RCX
|
|
Is there a program that allows you to download the prg files created from the Lego CD-ROM to the RCX without loading the Lego CD program? Help Appreciated! Adamski _______ <adamski2000@adamski...rve.co.uk> (28 years ago, 28-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.legos)
|
| |
 | | Re: NQC tutorial available
|
|
Mark, My first post here...thanks for the great tutorial. Tonight I'll try my first NQC program and your docs are great and easy to understand! Thanks! dan jenner (...) (28 years ago, 29-Mar-99, to lugnet.robotics)
|
| |
 | | Re: NQC tutorial available
|
|
Excellent Job Mark. Thanks for all of your hard work. -Phil (...) (28 years ago, 29-Mar-99, to lugnet.robotics.rcx.nqc, lugnet.robotics)
|