 | | Re: Inventory Checklist for Classrooms
|
|
(...) I made some inventory sheets for some designer sets by highlighting the WHOLE table/list from peeron, copying & pasting into Microsoft Word, then deleting the unwanted coulumns, etc. I believe the document needs the internet connection to open (...) (20 years ago, 4-Aug-06, to lugnet.robotics.nxt)
|
| |
 | | Inventory Checklist for Classrooms
|
|
The "inventory" picture on the NXT inside box cover nor the one in the pamphlet are not suitable for classroom use. Is there a lazy way of taking the peeron inventory with pictures (URL) and making an inventory sheet? (20 years ago, 4-Aug-06, to lugnet.robotics.nxt)
|
| |
 | | Re: Upgrading RCX to 2.0
|
|
(...) It's just software - otherwise they are essentially identical. Actually, the 1.0 hardware is the best because it has the external power socket - which was absent from the 1.5 and 2.0 RCX. The 2.0 set has a USB infrared tower - the older (...) (20 years ago, 3-Aug-06, to lugnet.robotics)
|
| |
 | | Upgrading RCX to 2.0
|
|
My first Mindstorms kit is the NXT but I have found some interesting projects for the previous generation RCX. My basic question is, is the upgrade from say a RCX 1.0 or 1.5 to 2.0 just a software update via your computer or is something that has to (...) (20 years ago, 3-Aug-06, to lugnet.robotics)
|
| |
 | | NXT and ROBOLAB 2.9
|
|
Here we are with our first NXT robot, a simple sonar wall-avoider. We are using ROBOLAB 2.9 as we want to continue with the ROBOLAB structures. This allows easy migration from RCX to NXT. ROBOLAB 2.9 uses a replacement firmware for NXT. Very (...) (20 years ago, 3-Aug-06, to lugnet.robotics)
|
| |
 | | CBS (Clicking Brick Syndrome) Patch availible
|
|
For those of you that have come down with the crippling "Clicking Brick Syndrome", it seems that there may finally be a fix availible. Take a look at: (URL) you had this problem during a firmware update, please try this and post the results. (20 years ago, 3-Aug-06, to lugnet.robotics.nxt)
|
| |
 | | RE: NXT Motors -- Speed vs Power Level
|
|
(...) I've done the same measurements/plots and found same linearity when 'brake' on inactive PWM cycles is used. Not so good when 'float' is used. This leads to a conundrum that I simply can't explain. If you use 'inactive brake' mode the motors (...) (20 years ago, 3-Aug-06, to lugnet.robotics, lugnet.robotics.nxt)
|
| |
 | | Re: NXT Motors -- Speed vs Power Level
|
|
I tried to plot power levels vs angular speed (in rad/s) and discovered goooood linearity ( remember how non-linear was RCX PWM)? The PID loop is a great idea, and I suppose that PID parameters should be tweakable. In SDK or HDK ( don't remember (...) (20 years ago, 3-Aug-06, to lugnet.robotics, lugnet.robotics.nxt)
|
| |
 | | Ruby NXT Bluetooth Data Logger
|
|
I wrote a simple ruby script to listen for messages sent via bluetooth: (URL) is comma delimited - timestamp, mailbox message was sent to, message like: Thu Aug 03 00:27:18 EDT 2006,1,"Chunky Robotic Bacon!" Thu Aug 03 00:28:20 EDT 2006,1,"true" Thu (...) (20 years ago, 3-Aug-06, to lugnet.robotics.nxt)
|
| |
 | | robot positioning system
|
|
RCX freaks surely will appreciate www.informatik.uni-k...arbeit.pdf !!! Cool ! (20 years ago, 2-Aug-06, to lugnet.robotics)
|
| |
 | | Re: NXT -> OSX Bluetooth Serial Connection
|
|
Oops! Thanks for letting me know. Should be renewed now and working hopefully! (...) (20 years ago, 2-Aug-06, to lugnet.robotics.nxt)
|
| |
 | | Re: NXT -> OSX Bluetooth Serial Connection
|
|
Your domain name has expired as of 7/27 Bob "Tony Buser" <tbuser+lugnet@gmail.com> wrote in message news:J3Csu0.4xA@lugnet.com... (...) (20 years ago, 2-Aug-06, to lugnet.robotics.nxt)
|
| |
 | | NXT -> OSX Bluetooth Serial Connection
|
|
In case anyone is interested, I figured out how to communicate via a bluetooth serial connection in OSX. The tricky part was figuring out that you have to create an incoming serial port device under Sharing in Bluetooth Preferences, open that (...) (20 years ago, 2-Aug-06, to lugnet.robotics.nxt)
|
| |
 | | Re: NXT Bluetooth on Intel Based Macs
|
|
(...) Unfortunately no. NXT-G is currently a PPC app so it has to run under rosetta. Bluetooth is unavailable to apps running under rosetta. You can connect to it via bluetooth outside of NXT-G though if you write a program to communicate with it (...) (20 years ago, 1-Aug-06, to lugnet.robotics, lugnet.robotics.nxt)
|
| |
 | | NXT Developer Kits released!
|
|
As prior LEGO press releases (URL) have stated>, the NXT developer kits would be available in August. And here they are! (URL) Software Developer Kit (SDK) Includes the NXT driver interface specification and necessary tools for creating third-party (...) (20 years ago, 1-Aug-06, to lugnet.robotics, lugnet.robotics.nxt, FTX)
|
| |
 | | NXT Bluetooth on Intel Based Macs
|
|
Has anyone got their NXT to work on one of the "new" Intel based Mac systems using the OSX operating system? Out of the box, I've heard NXT-G only supports USB connections on Intel Macs. But through standard OSX functionality you're able to set up a (...) (20 years ago, 1-Aug-06, to lugnet.robotics, lugnet.robotics.nxt)
|
| |
 | | Community challenge
|
|
NXTasy.org initiated a community challenge - throwing the blue ball from the NXT set, using only LEGO parts (no rubber bands, springs etc.). Prizes would be awarded to the best 5 robots. Details can be found in www.nxtasy.org website. (20 years ago, 1-Aug-06, to lugnet.robotics.nxt)
|
| |
 | | Great Ball Contraption at BrickFest '06
|
|
There has not been a great deal of public discussion about having a Great Ball Contraption at BrickFest '06, but there WILL be a GBC at BF06. If you missed your chance last year, when we had almost fifty modules, now is the time to start building. (...) (20 years ago, 31-Jul-06, to lugnet.robotics, lugnet.technic, lugnet.events, lugnet.events.brickfest, lugnet.robotics.events, lugnet.robotics.nxt, lugnet.robotics.rcx)
|
| |
 | | NXT Motors -- Speed vs Power Level
|
|
An explanation of when to use and when not to use the new NXT motor speed control option. The RCX supports only a motor power level control where the input is the percentage of time that power should be applied to the motor. The NXT supports not (...) (20 years ago, 30-Jul-06, to lugnet.robotics, lugnet.robotics.nxt)
|
| |
 | | Modified Alpha Rex
|
|
Does anyone have any plans for modifying the basic Alpha Rex robot to allow him to pickup objects? Thanks for your time, Tom (20 years ago, 29-Jul-06, to lugnet.robotics)
|
| |
 | | windows 2000 IR driver
|
|
My qestion how do i get the IR communication driver for windows 2000? (20 years ago, 29-Jul-06, to lugnet.robotics)
|
| |
 | | lugnet.robotics.nxt Curatorship
|
|
Since I was the person to (URL) this newsgroup's creation>, I'd like to take it on its curatorship. I don't know if it's something I'd like to do for several years, but getting it started is important. I was thinking the other day of volunteering (...) (20 years ago, 29-Jul-06, to lugnet.robotics.nxt, lugnet.admin.curators, FTX)
|
| |
 | | Re: Looking for Alternate Mindstorms 3804 projects
|
|
(...) Awesome! Thanks so much. later, James Mathis (20 years ago, 28-Jul-06, to lugnet.robotics)
|
| |
 | | Re: Looking for Alternate Mindstorms 3804 projects
|
|
(...) Hello James, I have a few on my site: (URL) (all except Panobot1), (URL) (RIS simon, bottom of page) Philo (20 years ago, 28-Jul-06, to lugnet.robotics)
|
| |
 | | Looking for Alternate Mindstorms 3804 projects
|
|
I'm looking for alternate projects and building instructions that use only the LEGO bricks in one Mindstorms set 3804. For sale books or on-line websites, either is welcome. Any pointers? Thanks! later, James Mathis (20 years ago, 28-Jul-06, to lugnet.robotics)
|
| |
 | | wav2rso utility
|
|
As some of you may know I have written a utility which can convert between wav files and rso (NXT sound) files. In response to an urgent call for help a couple days ago I went ahead and extended that utility so that it can convert either direction (...) (20 years ago, 28-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: Grööving Röböt
|
|
Hi Brian, (...) the music or the fish? (...) behind all that Javascriptery. Jürgen (20 years ago, 27-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: Grööving Röböt
|
|
(...) (URL) this song> instead ;) ROSCO (20 years ago, 27-Jul-06, to lugnet.robotics.nxt, FTX)
|
| |
 | | NBC for Linux (intel 32-bit)
|
|
With the assistance of Dwayne Fontenot I now have a binary of NBC which runs on intel 32-bit Linux platforms. You can get a copy from the NBC website. John Hansen (URL) (20 years ago, 27-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Grööving Röböt
|
|
My NXT likes ABBA. (URL) (20 years ago, 27-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | RIS Installer Problem
|
|
I would appreciate any help - I'm not sure this is the best place to post this but I need to get in touch with software-experienced people and this looks like a good start. If I should post this elsewhere, please let me know. If anyone has some (...) (20 years ago, 26-Jul-06, to lugnet.robotics.rcx)
|
| |
 | | GBC video from BrickFest 2005 on DVD
|
|
I'm planning on bringing a stack of DVDs with me to BrickFest this year containing (URL) my Great Ball Contraption video> from last year's event. This will be the original hi-res version (1.94 GB) and not the (URL) web version> linked to in that (...) (20 years ago, 26-Jul-06, to lugnet.events.brickfest, lugnet.robotics, lugnet.technic, FTX)
|
| |
 | | Mindstorms Education NXT base set inventory available on Peeron
|
|
Some people may be interested to compare with the shop edition. Yesterday I posted an inventory for the NXT Education base set, and it is now available: (URL) first inventory, so I hope I have not made any mistakes. :-) Many thanks to Philo, for his (...) (20 years ago, 25-Jul-06, to lugnet.robotics.nxt, lugnet.robotics)
|
| |
 | | Re: My First Classroom Use
|
|
Hi Matthias In article <44C61288.5020004@in...ects.com>, Matthias Paul Scholz <matthias.scholz@int...jects.com> wrote (...) a Bluetooth connection, to communicate with the NXT brick. These programs indicate that it is possible, but I have not yet (...) (20 years ago, 25-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | CNET: Lego robots march on Microsoft
|
|
CNET: Lego robots march on Microsoft (URL) (20 years ago, 25-Jul-06, to lugnet.robotics.nxt, lugnet.mediawatch) !
|
| |
 | | Re: Can Dacta 9751 be used with WindowsXP or Windows 2000?
|
|
(...) (URL) I've been working on a .NET class> for it. I have the serial port communication finished and am working on threading the sensor polling. In C# you'll be able use my DLL something like this: using Mindstorms.ControlLab; //... ControlLab (...) (20 years ago, 25-Jul-06, to lugnet.technic, lugnet.robotics, FTX)
|
| |
 | | Re: My First Classroom Use
|
|
Tony, (...) Presently, one could use Microsoft's Robotics Studio (see (URL) for instance) or NeXTTool by John Hansen (see (URL) Matthias Paul Scholz (20 years ago, 25-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | External Power for an RCX 1.5
|
|
I am attempting to hook an external power supply up to my RCX 1.5 so I can leave my bot running all the time. I have simply tried to hook up a 9V 800mA wall wart to the terminals, but it does not seem to work. Has anyone already tried this or (...) (20 years ago, 24-Jul-06, to lugnet.robotics)
|
| |
 | | Fwd: Blogger post failed
|
|
Can someone find out who is doing this and unsubcribe them? I get this every time I validate a lugnet message in robotics. I presume they have subscribed a blogging mail-in or something similar to the group. Danny ---...--- Forwarded message (...) (20 years ago, 24-Jul-06, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | Re: unsubscribing?
|
|
Ben, It appears you are on the crynwr list, which is maintained seperately from Lugnet. Roc appears to be directly on Lugnet. Roc - If you really have huge problems unsubscribing, post to lugnet.admin and ask Suz for help. Ben - I recommend first (...) (20 years ago, 24-Jul-06, to lugnet.robotics)
|
| |
 | | RE: unsubscribing?
|
|
This is very painful: impossible. I tried, had to give up, and so had to resort to automatically dump these in my junk mail. How awesome and inspiring this mail group might be for some, it has turned into a hassle for me (and now also for you I am (...) (20 years ago, 23-Jul-06, to lugnet.robotics)
|
| |
 | | Re: unsubscribing?
|
|
(...) First thing is that this should probably have been posted to lugnet.admin or .offtopic if at all. You need to go to the (URL) website, and then click on "newsgroups", under this, select "News by mail". You will need your email address and a (...) (20 years ago, 23-Jul-06, to lugnet.robotics)
|
| |
 | | Re: parallel RCX outputs
|
|
Hi Mark, (...) probably, I guess they would be started within the same millisecond, which would result in synchronized wafeforms. (...) It's not that bad, when the waveform is off the motor is floating. So the power control will be ineffective at (...) (20 years ago, 23-Jul-06, to lugnet.robotics.rcx)
|
| |
 | | Pictures of the NXT hardware
|
|
Hi, today I opened up a new NXT from the US and made some photographs: (URL) Jürgen Stuber <juergen@jstuber.net> (URL) key fingerprint = 2767 CA3C 5680 58BA 9A91 23D9 BED6 9A7A AF9E 68B4 (20 years ago, 23-Jul-06, to lugnet.robotics)
|
| |
 | | Re: parallel RCX outputs
|
|
(...) The flashing is a feature of the 1x2 and 1x4 lamps... if run in one direction, it's solid, but in the other it flashes. This comes from the old light and sound sets, where you might well want a flashing light. You're right that the two outputs (...) (20 years ago, 23-Jul-06, to lugnet.robotics.rcx)
|
| |
 | | Re: parallel RCX outputs
|
|
(...) If all motor ports are started and stopped together, does that synchronise the PWM waveforms? If not, then I don't recommend paralleling up. If so, then I recommend paralleling up only when motors are started and stopped together and are run (...) (20 years ago, 23-Jul-06, to lugnet.robotics.rcx)
|
| |
 | | Re: Flex system hose
|
|
(...) I had a look at the 1/8" plastic tubing in model railway shops and stalls at shows. I think it's ABS or polystyrene. I have no issues with cutting the tubes either :-) but I don't like painting stuff used as or with LEGO bricks. I think the (...) (20 years ago, 23-Jul-06, to lugnet.trains, lugnet.technic, lugnet.robotics)
|
| |
 | | unsubscribing?
|
|
sorry to post this here, but i really cant find an answer online how do i unsubscribe form the lugnet robotics list? r (20 years ago, 23-Jul-06, to lugnet.robotics)
|
| |
 | | Debut of NXT robot in a Singapore robotics competition
|
|
Among other types of robots, Telok Kurau Secondary School fielded an autonomous NXT robot in the finals of the East Zone Robotics Challenge 2006 which was held at the East Zone Science Carnival @ Victoria Junior College on 21 Jul 2006. The NXT robot (...) (20 years ago, 23-Jul-06, to lugnet.robotics.nxt, lugnet.loc.sg, FTX)
|
| |
 | | Re: My First Classroom Use
|
|
In article <J2r7BH.31K@lugnet.com>, John Brost <john.brost@gmail.com> wrote (...) Hi John, that's good news. :-) Though it is not clear to me how to control the NXT over Bluetooth at the moment. Hopefully the publication in August of developer (...) (20 years ago, 23-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: My First Classroom Use
|
|
In article <J2q8sH.8Mq@lugnet.com>, gypsy_fly <e_pilobello@yahoo.com> wrote (...) As of Friday I have a NXT Educational kit, and the software arrived on Saturday. (...) The NXT User Guide CD that comes with the Educational kit has document (...) (20 years ago, 23-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: Almost 300! And another Mindstorms Challenge! And more!
|
|
OK. Let's start over again: What I should have said is that I believe that if you have two vehicles each weighing 2 lbs (the maximum allowed by the rules), one rolling, one "walking", the probablity of making a "stronger" forwardly mobile unit is (...) (20 years ago, 22-Jul-06, to lugnet.robotics)
|
| |
 | | Re: Almost 300! And another Mindstorms Challenge! And more!
|
|
(...) I see a high amount of torque required on the Lego motors also. In general, and if done poorly, all you have is a bot with a stalled motor for one minute running at full power. Clutch gears could help, but it would have to be done in such a (...) (20 years ago, 22-Jul-06, to lugnet.robotics)
|
| |
 | | Re: parallel RCX outputs
|
|
Hi Chris, (...) I think so (warning, this is based only on theoretical knowledge). (...) That should be ok. Setting the power level might not work correctly, from looking at the ROM code it seems the PWM waveforms are not synchronized. Now comes the (...) (20 years ago, 22-Jul-06, to lugnet.robotics.rcx)
|
| |
 | | Re: Almost 300! And another Mindstorms Challenge! And more!
|
|
(...) So you have (in essence) a walking robot - but you wouldn't want to halve your traction by having only half of your feet on the ground at any one time - you'd want to have a robot with LOTS of feet and pick up just some tiny fraction of them (...) (20 years ago, 22-Jul-06, to lugnet.robotics)
|
| |
 | | Re: Almost 300! And another Mindstorms Challenge! And more!
|
|
I read the entire thread, and the rules and ask the question: Why must it ROLL at all? If friction is the name of the game, and if the wheels (tires) are the parts that have the "stickiest" qualities, then why not maximize the surface area of those. (...) (20 years ago, 22-Jul-06, to lugnet.robotics)
|
| |
 | | parallel RCX outputs
|
|
Can I put an electric 2x4 plate across output port A and B to increase the current I can draw from the brick? Chris 1. when I ran a few tests with a 1x2 lamp, I would get interesting results. A and B forward - ON A and B Reverse - ON A Forward B (...) (20 years ago, 21-Jul-06, to lugnet.robotics.rcx)
|
| |
 | | Re: My First Classroom Use
|
|
In lugnet.robotics.nxt, Tony Naggs wrote: <snip> (...) <snip> (...) Though I don't know a great deal about the bluetooth part of NXT, I thought I'd respond quash the idea of the NDA being in effect regarding this. That isn't the case (we are still (...) (20 years ago, 21-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: RCX infra red sensitivity
|
|
(...) Yes, the driver IC is current-limited to about 500mA (and thermal limited too), so it is very hard to destroy! (...) I have used NiMH batteries a lot on RCX, the only adverse effect I noticed is that the power available on motors is nearly (...) (20 years ago, 21-Jul-06, to lugnet.robotics)
|
| |
 | | Re: RCX infra red sensitivity
|
|
(...) I have not seen them on the RCX, but I have on other devices, where power transisotrs have died. Its all to do (I think) with the characteristics under load, and the fact that larger spikes in current may occur with rechargeables. If the IC (...) (20 years ago, 21-Jul-06, to lugnet.robotics)
|
| |
 | | Re: My First Classroom Use
|
|
In article <J2q8sH.8Mq@lugnet.com>, gypsy_fly <e_pilobello@yahoo.com> wrote (...) I imagine that the building skills are quickly learnt, and that this would be rather laborious. (...) Cool. :-) (...) Excellent. (...) The most common usage is for a (...) (20 years ago, 21-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: RCX infra red sensitivity
|
|
Hi Danny, (...) Have you seen real failures using some rechargeables batteries? I believe that the RCX motor driver IC is really foolproof, and I don't think anything could be destroyed using various kind of batteries (provided that the 9 or 10 (...) (20 years ago, 21-Jul-06, to lugnet.robotics)
|
| |
 | | Re: My First Classroom Use
|
|
At first I thought each student ought to have the experience of building each of the four models. It seems that having 9 kids choose one of four models and build it, saved us some time. They simply learned from each other's experience. Now they come (...) (20 years ago, 21-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: RCX infra red sensitivity
|
|
(...) Depending on the kind of rechargeables you are using, they generally have significantly different characteristics. They also often output a slightly lower voltage (about 1.2 or 1.3v per cell as opposed to the expected 1.5). If you have a (...) (20 years ago, 20-Jul-06, to lugnet.robotics)
|
| |
 | | Re: RCX infra red sensitivity
|
|
(...) Thanks for your replies. Both are RCX2 and I use the Robolab software. In Administrator / RCX settings you can set the RCX IR-power setting to high or low, but both were already in high. After some testing I found out that the main problem are (...) (20 years ago, 20-Jul-06, to lugnet.robotics)
|
| |
 | | Re: How do you create a new VI for NXT-G?
|
|
Shortly, an SDK will be made available that will allow for NXT blocks to be constructed using the same functions used to make the built-in blocks. The SDK will be made available on the NI site, probably linked from ni.com/mindstorms, and probably (...) (20 years ago, 20-Jul-06, to lugnet.robotics)
|
| |
 | | Re: Memory - Where did it go?
|
|
I'm coming in a little late on this topic, but I wanted to restate things just a little. NXT programs are built using a library of blocks. These blocks are not "built-in", to the compiler, but are simply shipped and placed in the palette. Each of (...) (20 years ago, 20-Jul-06, to lugnet.robotics)
|
| |
 | | Re: My First Classroom Use
|
|
(...) A team building AlphaRex had torn down and rebuilt the right leg module twice. Finally, they asked me where they could have gone wrong. Twice now, the leg they built looked like the exact opposite of the finished module on the screen. Why had (...) (20 years ago, 19-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: Almost 300! And another Mindstorms Challenge! And more!
|
|
(...) There was a good discussion a few weeks back... (URL) here's a chance to test out those theories. What is the "Right" speed??... Steve (20 years ago, 18-Jul-06, to lugnet.events.brickfest, lugnet.robotics, FTX)
|
| |
 | | Re: My First Classroom Use
|
|
Another new week and a fresh batch of 9 kids in a Lego Team Challenge class. This class is setup to help individuals take on a First Lego League challenge. Starting from scratch, each student (ages 9 - 13) built a model of their choice. No one (...) (20 years ago, 18-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: Hassenplug's "Mouse"
|
|
(...) A very cool model - I really like the 2" ball caster. See: (URL) sure to mouse over the letters in the popup window. -Tim (20 years ago, 18-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: Hassenplug's "Mouse"
|
|
"lledford" <lsrgroup@etcmail.com> wrote in message news:J2K5y2.p5x@lugnet.com... (...) (URL) (20 years ago, 18-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: Hassenplug's "Mouse"
|
|
Is this article accessible via the Internet. If so, what is the URL? Thanks Lamar "Brian Davis" <brdavis@iusb.edu> wrote in message news:J2Jxv9.L2v@lugnet.com... : In lugnet.robotics.nxt, David Schilling wrote: : : > the latest issue (July/Aug 2006) (...) (20 years ago, 17-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: Problem with LDT plugin
|
|
(...) snip (...) It seems that some people meet the same problem, so the answer : You must set in your project properties your "Default output folder" as yourProject/bin ( yourProject is the name of your project ;) ) Erik "brickerik" Amzallag (20 years ago, 17-Jul-06, to lugnet.robotics.rcx.java, FTX)
|
| |
 | | Re: Hassenplug's "Mouse"
|
|
(...) Neat. Has anybody else seen this? Kinda difficult to find here at the local bookstores... congradulation, Steve! (20 years ago, 17-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: RCX infra red sensitivity
|
|
(...) I'm guessing one of your RCX units is a 1.0, while the other is a 1.5 (labeled 1.0, but without the power port) or 2.0? There are a very few hardware difference betwen RCX versions, but this is one of them. See: (URL) I think you can adjust (...) (20 years ago, 17-Jul-06, to lugnet.robotics)
|
| |
 | | Re: RCX infra red sensitivity
|
|
(...) I think you can adjust the transmit value from the software, but not the reception sensitivity as far as I know. IR sensitivity can be affected by battery performance, ambient lighting (though not likely a factor if others are responding (...) (20 years ago, 17-Jul-06, to lugnet.robotics)
|
| |
 | | RCX infra red sensitivity
|
|
Hello everybody, One of my RCX units is far less sesitive to recieve a IR signal from another RCX than the other ones. Can this be adjusted in some way? Thanks, Eric. (20 years ago, 16-Jul-06, to lugnet.robotics)
|
| |
 | | Hassenplug's "Mouse"
|
|
I just saw Steve Hassenplug's "Mouse", an NXT-based robot in the latest issue (July/Aug 2006) MIT Technology Review. It's a two page spread (p. 22). Congratulations, Steve! -- David Schilling (20 years ago, 16-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: My First Classroom Use
|
|
(...) Thanks. I'll see if I can get it to work on our Windows XP IBM Thinkpad laptops. (Plug IBM for the donation to Saturday Academy) (20 years ago, 16-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: My First Classroom Use
|
|
(...) Thanks. I'll have the kids try the slight tilt this coming week. One kid needing to correct a model, was pulling so hard on a #15 beam, I thought he'd bend it out of shape! (20 years ago, 16-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: NXT to NXT communication?
|
|
(...) Very cool- the differential is very well designed, especially using only parts from the NXT. (...) Thats what I can't figure out how to do. I made a (modded) version of Brian Davis' DAZLR and using my grandfather's NXT have made a Remote (...) (20 years ago, 15-Jul-06, to lugnet.robotics)
|
| |
 | | Re: My First Classroom Use
|
|
(...) Try using the "Menu: Edit->Manage Profiles" dialog to create individual profiles for the teams. Then use the "User Profile" drop-down at the top of the window to let each team select their profile. [This is divined using the Mac version, but I (...) (20 years ago, 15-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: My First Classroom Use
|
|
(...) I find pins go into holes much easier if initially pushed at a slight angle, not more than about 5°. ROSCO (20 years ago, 14-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: My First Classroom Use
|
|
(...) Another 3 hours and "Spike" is complete. "AlphaRex" and "RoboArm T56" had to be torn apart and rebuilt when later modules showed there was something wrong with the base. Both are about halfway done. The AlphaRex team was quite frustrated as (...) (20 years ago, 14-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: My First Classroom Use
|
|
(...) a lot (if not all) of the technic instructions list the axles, ruberbands and beams in a small bubble on the page or at the front of the book with a 1:1 picture. Chris (20 years ago, 14-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: reverse ploarity circut protection??
|
|
(...) A bridge may be the only solution, but you will loose 1.2v across the diodes generally. Although it needs work (and is incomplete) I wrote a tutorial on interfacing a simple LED with an RCX, which shows ways using a bridge, or just simply (...) (20 years ago, 14-Jul-06, to lugnet.robotics)
|
| |
 | | Re: reverse ploarity circut protection??
|
|
(...) Yes, though the things to think about are the voltage drop across the diodes or other devices and the amount of power required. If only low power devices were being driven, such as the IR chip on its own, a simple bridge rectifier made from (...) (20 years ago, 14-Jul-06, to lugnet.robotics, FTX)
|
| |
 | | Re: How do you create a new VI for NXT-G?
|
|
(...) I don't know... yet. I think there are some further developments in the works on this however. Until then, note that three of the sensor blocks (touch, sound, and light) have the ability to output "raw" values, and two of these sensor blocks (...) (20 years ago, 14-Jul-06, to lugnet.robotics)
|
| |
 | | How do you create a new VI for NXT-G?
|
|
What is the process for creating a new VI for NXT-G, for like a custom sensor? thx, Aaron (20 years ago, 14-Jul-06, to lugnet.robotics)
|
| |
 | | Re: My First Classroom Use
|
|
(...) Huh. I always counted holes/studs, as most LEGO instructions are not at "true scale", are they? (...) Well, one nice thing about the content of the Mindstorms software is an *awful* lot of it is stored where you can get to it. For instance, (...) (20 years ago, 13-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: reverse ploarity circut protection??
|
|
(...) A bridge rectifier would work, very simple, but I'm not sure it's the best solution. ROSCO (20 years ago, 13-Jul-06, to lugnet.robotics, FTX)
|
| |
 | | reverse ploarity circut protection??
|
|
hey electronic wizards, i am working on a new lego project to rid the new IR train electronics from the bulky train base and i'm looking to build a circut protector for it. since i am planning on using standard lego conections 2x2x 2/3rds this is (...) (20 years ago, 13-Jul-06, to lugnet.robotics, FTX)
|
| |
 | | Re: My First Classroom Use
|
|
I'll use this space as my blog on my initial classroom experience with the NXT. Today, I had three pairs of boys (ages 10-11), building the arm, scorpion and biped. They had three hours from openning the boxes. Two teams (scorpion and biped) got to (...) (20 years ago, 13-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: BASIC for the NXT was Re: R21 - Robot Status
|
|
I think that $25,000 should inspire someone to write a basic compiler that spits out NXT Byte code. You could even get by if the compiler was written based using a non-enterprise version of basic. Lamar A retired system programmer/analyst "Chris (...) (20 years ago, 11-Jul-06, to lugnet.robotics)
|
| |
 | | Re: SDK for NXT
|
|
(...) This May press release stated it would be available in August: (URL) (20 years ago, 12-Jul-06, to lugnet.robotics)
|
| |
 | | My First Classroom Use
|
|
I'm currently teaching a Basic Programming and Pre-Robotics class for Saturday Academy. I've been using the RCX since it's invention. Today, I took a fully built NXT Tribot to class. First, I showed the class how to program a simple "go forward for (...) (20 years ago, 12-Jul-06, to lugnet.robotics.nxt)
|
| |
 | | Re: SDK for NXT
|
|
(...) I believe that folks at National Instruments are working on writing a document that describes the .rxe file format and the byte codes supported by the official NXT firmware's virtual machine. If I understand it correctly, the VM in the NXT (...) (20 years ago, 11-Jul-06, to lugnet.robotics)
|
| |
 | | SDK for NXT
|
|
Has a SDK describing the structure of the NXT bytes codes been released, or has there been any mention from Lego as to when it will be released. I assume that the MDP have seen something, is it released or still under NDA? Chris (20 years ago, 11-Jul-06, to lugnet.robotics)
|
| |
 | | BASIC for the NXT was Re: R21 - Robot Status
|
|
Rob Antonishen wrote: > > P.S. Anyone coming with an NXT "demonstration" t-o-w bot, since they > are not allowed to compete? > I ~would~ BUT......I !HATE! the GUI programing software. (Yes I know it was designed for kids, and I understand that I am (...) (20 years ago, 11-Jul-06, to lugnet.org.ca.rtltoronto, lugnet.robotics)
|