To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *201 (+100)
  Re: Resets
 
(...) I can't say that I have an explanation of why the motors would work at first and then cause problems later, but I can say that: Not all motors work with the Handy Board. In particular, motors that want to draw too much current (e.g., more than (...) (31 years ago, 22-Mar-96, to lugnet.robotics.handyboard)
 
  OC2 and OC3 outputs?
 
Where on the v1.2 board do I tie into the OC2, OC3, and OC4 output lines? Is there a schematic which has all the I/O pins labeled? I need to use the OC lines to output pulse trains. Does the library software use these ports for the motor() commands? (...) (31 years ago, 23-Mar-96, to lugnet.robotics.handyboard)
 
  Re: Resets
 
I have a few suggestions, these are all things that I have seen before to help reduce noise from motors I think that the problem might be due to crap getting back to the power line... thereby causing the DS1233 to say, time to reset... - try a (...) (31 years ago, 23-Mar-96, to lugnet.robotics.handyboard)
 
  Driving large motors with the Handyboard
 
Hi. I'm kinda new at this. I was wondering if anyone can help me answer this question. If I wish to drive large motors with a Handyboard, I understand that I have to use an h-bridge. Will I need to know anything about PWM before attempting this (...) (31 years ago, 23-Mar-96, to lugnet.robotics.handyboard)
 
  Re: Driving large motors with the Handyboard
 
There are several ways to do this. In Mobile Robots, they talk about H bridge circuits. If you are doing less than 2A use a L298 and some some clamping diodes ( these keep the driver chip from being fried when you turn the motor off). The L298 has 2 (...) (31 years ago, 23-Mar-96, to lugnet.robotics.handyboard)
 
  IC for Windows.
 
Just outta curiousity, what was IC Win developed with? (31 years ago, 23-Mar-96, to lugnet.robotics.handyboard)
 
  IC for Windows
 
(...) We use Microsoft Visual C++ (v. 4.0). -- Randy (31 years ago, 23-Mar-96, to lugnet.robotics.handyboard)
 
  Re: Resets
 
If I add a separate motor power to the L293's, can I keep the ground lines common? If not, what pins are motor ground? (I know pins 4,5,12, and 13 are ground) Thanks. -John (...) (31 years ago, 23-Mar-96, to lugnet.robotics.handyboard)
 
  Re: Resets
 
The MB design keeps ground in common, but the ground to the cpu, has an inductor in line with it, the HB also has a inductor on the ground side, I think. You might want to put an inductor on both sides of the motor, with a cap inbetween both of (...) (31 years ago, 24-Mar-96, to lugnet.robotics.handyboard)
 
  DC Motor Position control
 
I am wondering if anyone tried to write an IC program for DC motor position control using PID/P or whatever with a handyboard. I am also looking for a good precision DC motor (with encoder and gearbox integrated), I very appreciate your help for any (...) (31 years ago, 24-Mar-96, to lugnet.robotics.handyboard)
 
  Re: OC2 and OC3 outputs?
 
Take a look at the schematics, which are linked from the top page of the Handy Board web site. The info you are looking for is in the CPU / memory schematic. For the DC Motor outputs, the board uses a separate output latch---not the timer outputs. (...) (31 years ago, 24-Mar-96, to lugnet.robotics.handyboard)
 
  TOC 2 & 3
 
AAAARRRGGGHHHHHH!! After the pain of relearning assembler and getting interrupt routines to work, it seems my assumption of the availability of TOC 2 & 3 is incorrect. I need 2 (wanted 4) pulse trains to go out. According to the diagrams Fred (...) (31 years ago, 24-Mar-96, to lugnet.robotics.handyboard)
 
  pulse trains
 
Mike, Out of curiosity, what are you using the pulse trains for? (If you're running multiple servos, I think I know a single-chip hardware mod to drive up to 8 servos from a single timer output.) -- Randy (31 years ago, 24-Mar-96, to lugnet.robotics.handyboard)
 
  Re: Driving large motors with the Handyboard
 
(...) Thanks for the tip. I got a hold of the book and read some of it. :) I was wondering if sending pulses to the motor would cause "choppy" rotation....or does it occur so fast that inertia effects make it "smooth". Also, with an h-bridge, is it (...) (31 years ago, 25-Mar-96, to lugnet.robotics.handyboard)
 
  (no subject)
 
UNSUBSCRIBE (31 years ago, 25-Mar-96, to lugnet.robotics.handyboard)
 
  unsubscribe
 
unsubscribe (31 years ago, 25-Mar-96, to lugnet.robotics.handyboard)
 
  digital output
 
Is it possible to use any digital output on the Handy Board without loosing the monitor (or anything else for that matter)? Scott sherman@plains.nodak.edu (31 years ago, 25-Mar-96, to lugnet.robotics.handyboard)
 
  Re: unsubscribe
 
In order to be removed from the Handy Board mailing list, please send e-mail directly to me, Fred Martin. There is no need to announce your request to the entire list. Enclosed are instructions from the mailing list page on the web site. -Fred -- (...) (31 years ago, 25-Mar-96, to lugnet.robotics.handyboard)
 
  Re: pulse trains
 
(...) I'm doing signal conditioning for pan/tilt and (ultimately) drive/steer signals from an RC receiver and driving servos with the processed signals. All power for the servos is external, so all I need is signals through the Handyboard. -mike * (...) (31 years ago, 25-Mar-96, to lugnet.robotics.handyboard)
 
  Re: Get Alias Info
 
In your message you said: (...) Arghh! The "get alias info" command is on the web pages, i.e., (URL) everyone, remember there is nothing automated about the handy board mailing list. to get on it, I must manually put you there. to get you off it, i (...) (31 years ago, 25-Mar-96, to lugnet.robotics.handyboard)
 
  How to run 8 servos by adding one HC chip
 
(...) Warning: I haven't tried the following idea. Single chip add-on to control 8 servos using one timer line and a few digital outputs: The 74HC238 is a 3 to 8 demultiplexor. (see (URL) for datasheets). Unlike the more common HC138, its outputs (...) (31 years ago, 26-Mar-96, to lugnet.robotics.handyboard)
 
  process control question
 
Hi all, I used the routines in Mobile Robot as a guide in building routines for my robot. I have an IR detector setup like the one described using the Sharp detector to detect left and right obstacles. I have a round robot with three bumper switches (...) (31 years ago, 26-Mar-96, to lugnet.robotics.handyboard)
 
  Get Alias Info
 
Get Alias Info (31 years ago, 26-Mar-96, to lugnet.robotics.handyboard)
 
  pneumatic arms
 
Since electric motors running off small, mobile power supplies tend to be weak and slow, I was considering designing a pneumatic arm powered by an onboard container of compressed air. Can anyone tell me where I can obtain pneumatic solenoids (...) (31 years ago, 26-Mar-96, to lugnet.robotics.handyboard)
 
  Re: Sony IR decoding routine!
 
I'm having trouble getting sony-ir.icb to load. Every time I try, I get the following error message: FATAL INTERNAL ERROR: ILLEGAL LINE IN .s19 FILE I've re-downloaded and installed both the sony-ir.icb and pcode_hb.s19 files but continure to get (...) (31 years ago, 26-Mar-96, to lugnet.robotics.handyboard)
 
  Re: Sony IR decoding routine!
 
I downloaded the source code sony-ir.asm and assembled with asii_ic.bat and the resulting .icb file worked fine. I jumped the gun asking for help. Thanks any way. Ram. I'm having trouble getting sony-ir.icb to load. Every time I try, I get the (...) (31 years ago, 26-Mar-96, to lugnet.robotics.handyboard)
 
  .icb files
 
(...) I'd recommend moving up to IC 3.1. The current Windows and UNIX beta versions of IC 3.1 should accept .s19 files with any newline convention (CR, LF, CR-LF). (We're fixing that in the Mac IC beta soon). If you do get "illegal line in .s19" in (...) (31 years ago, 26-Mar-96, to lugnet.robotics.handyboard)
 
  problems with ICB files
 
oh come on, Randy, you're acting too much like a big software company! "Don't worry that that feature is broken, it will be fixed in our new version!"Most of the time, people would rather hear a workaround than be told to upgrade! Regarding the (...) (31 years ago, 26-Mar-96, to lugnet.robotics.handyboard)
 
  Re: icb fixed in IC 3.1
 
(...) Guess it comes from trying to earn a living selling software :) At any rate, I had seen the workaround for free IC posted several times in the past week, so I thought I would add rather than repeat information. Sorry for the self-serving (...) (31 years ago, 27-Mar-96, to lugnet.robotics.handyboard)
 
  Help!
 
Hi everyone, I had posted a question or two and some of you had answered me with some helpful info. Unfortunately, I accidentally erased all my messages before I gat a chance to read and save them. So,...if any of you still have any message that was (...) (31 years ago, 27-Mar-96, to lugnet.robotics.handyboard)
 
  Re: pneumatic arms
 
(...) Try this site: (URL) may contain some info you need...perhaps? (31 years ago, 27-Mar-96, to lugnet.robotics.handyboard)
 
  How to free up OC2?
 
I believe I can disconnect the OC2 pin from the unneeded IR-Xmit function, so I can divert it for my own use. Would that require any trace cutting, or perhaps removal of the LED Xmitter? Or, better yet, is it all a software change? Fred, I know (...) (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  1050mA Dc Motor
 
Hi everybody I want to know if I can drive a DC motor which need 1050 mA as a starting current, using the miniboard. Thanx. Hachemi. (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 1050mA Dc Motor
 
If you use the Texas Instruments replacement for the L293D chip, you should be in business. Also, mini board questions should go to the robot board mailing list (see enclosed). -Fred -- This message was composed using Articulate Systems' (...) (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  600 mA Limit
 
I was wondering if the 600 mA limit on the motor driver chip is a limit for the total source current of all four motor outputs or for each individual motor output. If its 600 mA for each motor output,...will the chip get hot when running with 4 (...) (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 600 mA Limit
 
The 600 milliamp limit is per channel, but for a given motor, two channels are wired in series. So you don't get 1200 milliamps per motor but only 600. This would still yield 1200 milliamps per chip, since there are drivers for two motors. Also, if (...) (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 600 mA Limit
 
I just realized that getting 1200 milliamps running two motors bi-directionally is equivalent to running four motors uni-directionally at 2400 from a total power dissipation standpoint. I.e., there are still 600 milliamps running through each (...) (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  Miniboard/Handyboard.
 
The Miniboard manual says that it can vary the motor speed at 16 levels at either direction. It was mentioned earlier that the Handyboard can vary only 8. Is this correct? I'm seeing that the Miniboard motor drivers has a higher resolution than the (...) (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 600 mA Limit
 
(...) You mean running FOUR motors uni-directionally from ONE L293D chip, right? ...and TWO motors bi-directionally from ONE L293D chip? (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  Re: Miniboard/Handyboard.
 
it is only a difference in software. The Handy Board software does eight levels; the mini board software---which is different---does 16. -Fred -- This message was composed using Articulate Systems' PowerSecretary, a Macintosh-based speech-to-text (...) (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 600 mA Limit
 
In your message you said: (...) Yes, that is what I mean. -Fred (31 years ago, 28-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 600 mA Limit
 
(...) OK. I just wanted to make sure I'm understanding the material. So, my guess is that in order to drive the 4 motors off one chip, you would have to ground the other lead of each motor? So, does that mean that there is 2.4 A source from the chip (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  expansion board
 
Hi Everyone, I was wondering if someone could point me to where all the software for accessing the Handy Board's expansion board features are located. Specifically, I was wondering if there is code to access the additional A/D ports, servos, (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  Re: expansion board
 
the code has not yet been written. My hope was that some people who got expansion boards might want to do some of the work themselves. For example, the code for dealing with the analog ports can be taken from previous code for the 6.270 board and (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 600 mA Limit
 
(...) from the L293D ground? yes, this would be correct. Well, there would be 2.4 amps running through the chip's power source, into the motors, and into ground. ...totaling 4.8 A runniing throught the entire chip fro m a power dissipation (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  pcode, libraries for two servos
 
For people interested in using the piezo output line for a second servo, I've put libraries and new pcode's online at (URL) under "IC-related packages"). The new pcodes disable the beeper code in IC, and free up the line for other uses. The library (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 1050mA Dc Motor
 
With teh TI chips, you might get away with it, just do not stall the motor for long. It will not work with the L293Ds, they are rated at 600 ma ( they might work for awhile) (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  digital output
 
Hi, I am wondering if there is any means of digital output other than the motor ports such as the miniboard has. The miniboard has the bank of digital i/o ports. The handyboard has the digital input but I am not sure about digital output other than (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  two servo code
 
(...) Hey Randy, it would be cool if you could modify that code to use TOC3, which is free and available on the expansion bus, rather than disabling the piezo. Maybe somebody else wants to do this. -Fred (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  Re: two servo code
 
(...) Fly-in-the-ointment: I'd still rather disable the IR Xmit function than the buzzer. My application would like to use the buzzer to communicate audibe condition codes. I appreciate Randy's effort to sacrifice the piezo buzzer so we can supply (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 600 mA
 
Thanks. This helps clarify things about the motor features alot. I was looking into transistors for the first time. I was wondering if you can connect the L293D output to the base of a high current transistor. ...and the collector and emmiter in (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  Re: two servo code
 
(...) Actually, none of the default functions in pcode_hb.s19 actually use the IR transmit line -- you have to load in someone's ir transmit icb file. so that line is completely up for grabs. mike, it shouldn't be too ahrd to work from Randy's (...) (31 years ago, 29-Mar-96, to lugnet.robotics.handyboard)
 
  PA7
 
Another Q or 2 about using the servo capabilities of the handy board. It has been established that the servo motor output is actually digital output 9 (J2-9) (position numbered 15 (on the silk screen) of connector J2) 1) Is there a separate (...) (31 years ago, 30-Mar-96, to lugnet.robotics.handyboard)
 
  Re: PA7
 
(...) no,this is wrong. The servo output is J2 - 9, not J2 - 15. (...) you need a 5 volt source to power the servo. The Handy Board 5 volt supply can be used, but this will put a lot of stress on the system regulator. It would be better to get a (...) (31 years ago, 30-Mar-96, to lugnet.robotics.handyboard)
 
  Re: 600 mA
 
Note that the spec sheet for the L293D states that the package can only dissipate 5 watts. With a voltage drop of 1.3 volts that is 3.85 amps total through all drivers. However, since that is the absolute maximum rating your probably looking more (...) (31 years ago, 30-Mar-96, to lugnet.robotics.handyboard)
 
  New version of Mac IC: 3.1 beta 5
 
A new beta version of Interactive C for the Macintosh, Mac IC 3.1b5 is now online at: (URL) and improvements from beta 4: * Printing is now enabled * Definition files and board recognition are better handled * Files, functions, and globals info (...) (31 years ago, 1-Apr-96, to lugnet.robotics.handyboard)
 
  *WARM* L293D's on Handyboard
 
Today I ran out to Toys 'R' Us and bought a wired-remote controlled excavator to serve as the base for my HandyBoard. It seems to be causing me a little problem, though. Before I removed it from the controller that contained the battery (...) (31 years ago, 1-Apr-96, to lugnet.robotics.handyboard)
 
  hooking up to R/C car
 
(...) We've had success interfacing digital signals directly to the drive circuitry that's already present on some R/C vehicles. The problem you're running into is that R/C motors just draw too much current for 293's. (If you look at the controller (...) (31 years ago, 1-Apr-96, to lugnet.robotics.handyboard)
 
  Re: hooking up to R/C car
 
(...) There aren't any control electronics to this thing at all, really. There's four switches on the control box, some wires going to the vehicle, and four motor/gearbox combos in the machine that the wires supply power to. No drivers, no heat (...) (31 years ago, 1-Apr-96, to lugnet.robotics.handyboard)
 
  Re: hooking up to R/C car
 
(...) A really wild/money is almost no object idea would be to get electronic speed controls from radio controlled cars. These things can control up to several tens of amps continuously. You can control them like controlling a servo. Their cost is (...) (31 years ago, 1-Apr-96, to lugnet.robotics.handyboard)
 
  26 VDC motor
 
Using the handyboard, can we drive a DC-motor which has a nominal voltage of 26 volt, (the starting current is less than 600mA). Thanx. Hachemi. (31 years ago, 2-Apr-96, to lugnet.robotics.handyboard)
 
  expansion interface
 
How is the beta-test of the expansion interface progressing? Anybody care to estimate when the design might be finalized so I could purchase one? How much would a kit be expected to cost? \---...---\ \ John Mathews jkm@po.cwru.edu \ \---...---\ (31 years ago, 2-Apr-96, to lugnet.robotics.handyboard)
 
  (no subject)
 
Does anyone know if you can do this to the L293D chip to increase the current? _____- motor +________ / | L293D |/ | motor output___...___| + |\ \->- baterry | | - | | | | ---...--- The transistor in the center would be a high current one. Would (...) (31 years ago, 3-Apr-96, to lugnet.robotics.handyboard)
 
  Question !
 
What should be the nominal voltage of the DC-Motors for the handyboard, I know that in miniboard its 6v - 36v. Thanx. Hachemi. (31 years ago, 3-Apr-96, to lugnet.robotics.handyboard)
 
  RE:
 
It would work but it would be uni-directional. --Chuck ---...--- From: MAR ERICSON[SMTP:mar@cooper.edu] Sent: Wednesday, April 03, 1996 11:27 AM To: handyboard@media.mit.edu Does anyone know if you can do this to the L293D chip to increase the (...) (31 years ago, 3-Apr-96, to lugnet.robotics.handyboard)
 
  Re: High current motors
 
Do you have to choose a transistor that will switch somewhere near and below 9 volts? Cause Fred mentioned that the handyboard is rated for 9V motors. But, does this mean that the pulse generator make 9V square waves? (...) (31 years ago, 4-Apr-96, to lugnet.robotics.handyboard)
 
  Re: High current motors
 
How about this one? ...to enable two directional rotation. ___...___ motor ___...___ | | | | -> / / -> |/ |/ |/ |/ ---| ---| ---| ---| | |\ | |\ | |\ | |\ | \ | -> | -> | \ | | | | | | | | | | | | | | | | | vcc | gnd | gnd | vcc | | | | | | | | | | (...) (31 years ago, 4-Apr-96, to lugnet.robotics.handyboard)
 
  Re: High current motors
 
I think the question on how to run higher current motors has got to be the most asked question here. Maybe we should add more info to the FAQ or something. Anyway, here is Chuck McManis' solution from a while back. I hate to send out something that (...) (31 years ago, 5-Apr-96, to lugnet.robotics.handyboard)
 
  Expansion board
 
How many Polaroid range sensors can the expansion board have up to. One? What kind of signal does it produce? (31 years ago, 5-Apr-96, to lugnet.robotics.handyboard)
 
  mseconds
 
Is there a way to get sub-milisecond times measured with the handyboard? I was thinking of trying to modify msecond but I can't look at it now that it is a primitive. Dirk (31 years ago, 7-Apr-96, to lugnet.robotics.handyboard)
 
  http://lcs.www.media.mit.edu/groups/el/projects/handy-board/maillist.htm
 
i would like to use the list. thankyou, Jeff (31 years ago, 7-Apr-96, to lugnet.robotics.handyboard)
 
  Re: Handyboard expansion status
 
(...) I don't have one of the beta versions of the expansion board, but I've been building my own expansion boards and putting them on the HB. One thing that I've found is problematic with the HB design, in regards to expansion board design, is that (...) (31 years ago, 7-Apr-96, to lugnet.robotics.handyboard)
 
  Pcode instructions?
 
OK. I know this is going to be a long shot, but here goes: Are there any docs on the pcode? I.e. is there some way that I can learn what I need to learn to modify the source code pcode.asm besides reading the file pcode.asm and tearing my hair out? (...) (31 years ago, 8-Apr-96, to lugnet.robotics.handyboard)
 
  more address lines on expansion board
 
Hi Brian, When Fred and I designed the Rev 2.0 6.270 controller, we consciously made the expansion bus small and simple. For most expansion devices, the pre-decoded chip selects make more sense than sending all the address lines, since the latter (...) (31 years ago, 8-Apr-96, to lugnet.robotics.handyboard)
 
  HB design
 
I got my handyboard on Saturday, and followed the assembly instructions that Fred did, and was thoughoughly impressed. Fred, you did great work, and have really done a great service to all of us. Thanks. (31 years ago, 8-Apr-96, to lugnet.robotics.handyboard)
 
  Sonar
 
I don't have my Handy Board yet, but I do need some help in locating a Sonar Ranging Module. I have looked everywhere I can think of to no avail. Even emailed Polaroid and asked them. Twice. Still have no response from them. Where do I get a (...) (31 years ago, 8-Apr-96, to lugnet.robotics.handyboard)
 
  Re: Sonar
 
(617)386-3965 OEM Components Group 3 kits: $299, $165, $99 You're probably interested in th $99 one wich has 2 Rangers and 2 Transducers. (...) (31 years ago, 8-Apr-96, to lugnet.robotics.handyboard)
 
  Re: Sonar
 
Speaking of Polaroid ultrasonic sensors, does anyone know if there's a product out there that can multiplex a few of the sensors? Thanks. (31 years ago, 9-Apr-96, to lugnet.robotics.handyboard)
 
  RE: Sonar
 
The Robotics Practitioner (trp@footfalls.com has part 1 of an article about this in the Fall, 1995 edition by Bavid Musliner (musliner@src.honeywell.com) and Rick Moll (rick@footfalls.com). Part one is concepts; part 2 will present detailed design. (...) (31 years ago, 9-Apr-96, to lugnet.robotics.handyboard)
 
  Emitting 40khz IR
 
How do I send out 40khz IR on the handyboard IR port so that I can use a Sharp IR detector for proximity sensing? I would need a signal that wasn't modulated at 100 or 125 hz, right? Just a straight 40khz signal. Any help would be appreciated. -John (31 years ago, 9-Apr-96, to lugnet.robotics.handyboard)
 
  Re: Sonar
 
Yeah! This would help alot! Who is trp@footfalls.com? Is this person someone who posted the article once in handyboard mailing list? (...) (31 years ago, 9-Apr-96, to lugnet.robotics.handyboard)
 
  RE: Sonar
 
The Robotics Practitioner is a magazine about robotics targeted more for students and hobbyists than many of the professional Journals. Their email address is: trp@footfalls.com. Other two email addresses in the previous messge are the articlel's (...) (31 years ago, 9-Apr-96, to lugnet.robotics.handyboard)
 
  Polaroid Sonar Bulk Buy
 
Hello Everyone, As you may or may not know I am hosting a Bulk Buy for the Polaroid 6500 Sonar Ranging Modules and matching Transducers. The deadline for orders to be in by regular mail is coming up quick, Friday, April 19, 1996. If you are (...) (31 years ago, 9-Apr-96, to lugnet.robotics.handyboard)
 
  fuse on handyboard
 
I'm curious - what is the maximum current the Polyswitch fuse on the handyboard will allow to pass through it? I'm designing an H-bridge circuit to allow me to drive a heftier base with the handyboard, and I'm trying to figure out if I can still (...) (31 years ago, 10-Apr-96, to lugnet.robotics.handyboard)
 
  Re: Emitting 40khz IR
 
poke(0x1000,0x40); will turn the IR on at 40KHZ and poke(0x1000,0x0); will turn it off. (...) Dr. M. K. Ramasubramanian Assistant Professor Department of Mechanical and Aerospace Engineering North Carolina State University Box 7910 Raleigh, NC (...) (31 years ago, 10-Apr-96, to lugnet.robotics.handyboard)
 
  ???
 
Would anyone think of selling me an ASSEMBLED and used Handy Board for cheap. I have very limited funds and would appreciate any price reduction. Thank you. You can E-mail back on the mailing list or to Babylon007@aol.com. (31 years ago, 10-Apr-96, to lugnet.robotics.handyboard)
 
  Nuggets
 
While trying to unload some IS1U60 IR receivers, I found the sharp data site. It turns out that the IS1U60 has a center freq of 38 khz, while 40khz is is well within its pickup range, I wonder if changeing the circuit on the HB to 38khz would (...) (31 years ago, 10-Apr-96, to lugnet.robotics.handyboard)
 
  TCNT register !
 
I want to know if the time we get from timer (TCNT) is in second or milisecond. I was trying to run the handyboard for my first time, and I am confusing about the power supply, I don't know if the power supply should be plugged in the handy board (...) (31 years ago, 11-Apr-96, to lugnet.robotics.handyboard)
 
  RE:TCNT reg
 
(...) The battery goes to the (+) (-) spots, and the charger plugs into either the Handy Board itself (near the frob knob) or on the serial/battery board. The system time, while running IC (which is what I assume you're going to do) is in (...) (31 years ago, 11-Apr-96, to lugnet.robotics.handyboard)
 
  4 line LCDs and other LCD questions
 
Dear HB suppliers: Can anybody sell us bigger LCDs for the HandyBoard? I need at least 4 line LCD or other similar type. It will be used in complete darkness, so it should be illuminated. Thanks. Alexander A. Chaihorsky President, ULTRA-RES Corp. (...) (31 years ago, 11-Apr-96, to lugnet.robotics.handyboard)
 
  re:4 line LCDs and other LCD questions
 
(...) HB experts, correct me if I'm wrong, but if someone wanted to use an LCD bigger than 2x16, wouldn't the pcode have to be recompiled? I know that in the pcode.asm file there is reference to displays up to 2x80 (of which I have 4 and none work (...) (31 years ago, 12-Apr-96, to lugnet.robotics.handyboard)
 
  Servo
 
Does anyone know how to activate the servo on HandyBoard with IC? (I am going to use the Polaroid Sonar Ranger when it gets here.) When I try to load 'Servo.C', the supplied program, I get 6 or 8 errors of unassigned lables. I assume that (...) (31 years ago, 12-Apr-96, to lugnet.robotics.handyboard)
 
  Re: Servo
 
(...) You need to do a 'load servo.icb' before you do the 'load servo.c' command. The .icb file contains the code described in the servo.asm file, in a binary format. The code in the servo.asm file does the actual work of running the servo output. (...) (31 years ago, 12-Apr-96, to lugnet.robotics.handyboard)
 
  Re: Servo
 
you have to load both servo.c and servo.icb. -Fred -- This message was composed using Articulate Systems' PowerSecretary, a Macintosh-based speech-to-text dictation system. Please forgive any sloppiness in the formatting. Thanks. -Fred In your (...) (31 years ago, 12-Apr-96, to lugnet.robotics.handyboard)
 
  h-bridges, current info
 
I'm trying to figure out a couple things. First, can four NPN transistors be used to form an h-bridge? I was looking in a book, the Robot Builder's Bonanza, which features a circuit which uses four TIP41 transistors. However, don't most h-bridges (...) (31 years ago, 12-Apr-96, to lugnet.robotics.handyboard)
 
  Ultrasound Range-Finding
 
I would like to add range-finding of some description to my robot project. I would prefer to make it as cheap as possible. I have heard of the various polaroid-based schemes, but these all sound as though they are $90+ solutions. Does it have to be (...) (31 years ago, 12-Apr-96, to lugnet.robotics.handyboard)
 
  Re: h-bridges, current info
 
(...) the fuse is rated for about 2.5A continuous. If that is not enough, get one rated for more current, or replace it with a wire and make sure not to short out the nicads, or you'll get 30 to 40 A flowing. -F (31 years ago, 13-Apr-96, to lugnet.robotics.handyboard)
 
  Battery level monitoring?
 
Has anyone figured out how to monitor the battery level on an HB1.2? I would like to be able to use a circuit similar to the one published in the Jones Mobile Robots book, but it connects output directly to an analog port and is confused by the (...) (31 years ago, 13-Apr-96, to lugnet.robotics.handyboard)
 
  Motor Voltage Hack
 
Want to use motors of different voltage than the 9V required by HandyBoard? Then read this. I had decided to use converted Servo's as wheel drives, and they want about 4.8V. In studing the diagram and board layout I discovered that the HB batterys (...) (31 years ago, 13-Apr-96, to lugnet.robotics.handyboard)
 
  Extention Board?
 
I heard that there is an extention board for the HandyBoard. Does anyone know if it is available yet, and where I can get one? Price also? Thanks Larry ***...*** Larry Randall ***...*** If it works Don't fix it! ***...*** lrand@cts.com ***...*** (31 years ago, 13-Apr-96, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR