 | | Re: HB and ICC11..
|
|
(...) The trick is to copy the mode-change/LCD code into the on-chip RAM and execute it from there. This code must change to single-chip mode, write to the LCD, then change back to expanded mode. When in single-chip mode, you lose access to any (...) (29 years ago, 2-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB and ICC11..
|
|
Howdy- I saw your posting on the HandyBoard list. I don't know if I have any LCD code laying about or not but I'll look and see. Meanwhile, I noticed in your letter that you indicated you were using ImageCraft-C with the HandyBoard. I was wondering (...) (29 years ago, 2-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB and ICC11..
|
|
please post any answers to the board, as I also have ImageCraft's C compiler and have been as yet unable to set it up properly. thanks, -patrick (...) HandyBoard. (...) your (...) using (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Trouble shooting 7.2.2 (The digital inputs)
|
|
you are using the wrong library file. configure IC to use lib_hb.c, not lib_r22.c. -fred In your message you said: (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Trouble shooting 7.2.2 (The digital inputs)
|
|
(...) Thanks, that fixed the problem. I am happy to find that the problem was just software. Anthony Oren Loeppert *** (URL) * o* * ***> * * * * * | | * * | / * * |/ * * * * * * **\ (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | lcd and ds1233-10 supplier
|
|
Just for the record, I was able to get the Hitachi LCD and the Dallas Semi. voltage monitor from Sterling Electronics. Their number is (512)836-1341. This location is in Austin, TX, but I think that they have a 1800 number, though I don't know it. (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Future versions of handyboard?
|
|
(...) I suspect there probably aren't such plans. One of the problems is the amount of infra-structure needed for a successful board. Basically you need a good board and a good development environment, and you have to be as inexpensive as possible (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Svar: Trouble shooting 7.2.2 (The digital inputs)
|
|
Hej I'm had the same problem, until i found that I loaded some programs via lib-file, not suitably for HB. (lib_r22.c) It seems you are running some programs for the 6.270. Have You setup IC correct? Try run c:\IC -config. Check out your lib-files. (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: voice synthesis
|
|
(...) Wow, impressive board. However, it's a bit out of my price range - I was hoping for a solution just about as cheap as the Radio Shack one used to be. Quality of speech isn't that much of a factor, I'm merely going to try and put this thing on (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Chip Puller
|
|
Does anyone know where I can buy a chip puller for the 6811. Robin (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Chip Puller
|
|
R> Does anyone know where I can buy a chip puller for the 6811. R> Robin Jameco sells 'em ((URL) Part no 16766 $3.95 If you are careful, and stuff, you can use little screwdrivers to pull chips. Wiggle one corner loose, then the other, then the (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Chip Puller
|
|
(...) This is good advice! Their sales number is: (800) 831-4242. I think I saw a similar device in Radio Shack the last time I was there as well. I don't know what the price was but probably comparable. (...) This is NOT good advice! :) It is my (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: voice synthesis
|
|
There used to be a company that made a vowel synthesis kit, but I think they pulled it. Some science catalog company still had a bunch, back in January, and I have one (oh joy of joys). I may still have a scanned image of the schematics from it that (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Backlit screen and external power
|
|
Hi, 1.Does anyone know of a backlit and/or larger compatible LCD screen? 2.Are the problems with using a larger power supply than 500ma related only to battery overcharging and in this case can the battery be replaced with a larger amperage power (...) (29 years ago, 4-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Auton. underwater vehicles
|
|
Most robot builders work on mobile and walker robots. A few developers, however, have addressed another challenge: autonomous underwater vehicles. This research requires new sensors and special concern to mechanical details. With one major mistake, (...) (29 years ago, 4-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: voice synthesis
|
|
Jeff, JDR Microdevices sells the General Insturments CTS256AL2 chip (GI8642CAA) for ** $4.95 **. This is (I think) a slightly newer version of the same chip that Radio Shack used to sell. I bought one of those with an order from JDR, but haven't had (...) (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Backlit screen and external power
|
|
(...) Hi there Joe- (...) Yes, you're gonna like this- just about any "Optrex-compatible" LCD display can be used on the HandyBoard. There are two caveats however, most of these displays have a 14-pin header connection and not the 14-pin inline (...) (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Unsubscribe
|
|
Unsubscribe Me Please! (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | vector 2 x sample programs
|
|
Hello Everyone: I have just finished hooking up my vector2x compass and it seems to work fine thanks to Tom Brusehaver's good work and instructions.The only goof I made was to reverse the input and output lines. After about two hours of inspection (...) (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Rules for next years firefighting contest
|
|
Has anyone heard when next years rules will be out for the Trinity firefighting contest? Are there going to be any major changes or are they going to stay about the same? Thanks. Keith Keith Soldavin kas219@email.psu.edu (URL) (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: vector 2 x sample programs
|
|
(...) Eric Olson (robojoc@worldnet.att.net) may be able to help you. He describes his GeneSys-1 robot in the latest Seattle Robotics Society newsletter. It uses ultrasonic rangefinding, IR, and a Vector 2X compass for navigation. Nice machine. (URL) (...) (29 years ago, 6-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Auton. underwater vehicles #2
|
|
Here are more web sites that provide useful underwater vehicle information: Unmanned Underwater Vehicle Society (UUVS) at U of Florida This student group had the only functioning AUV during the 1996 AUVSI Annual Symposium and Exhibition. Although (...) (29 years ago, 6-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | v2x sample code
|
|
Hello Everyone: I have just finished hooking up my vector2x compass and it seems to work fine thanks to Tom Brusehaver's good work and instructions.The only goof I made was to reverse the input and output lines. After about two hours of inspection (...) (29 years ago, 6-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: voice synthesis
|
|
(...) This is the text-2-speech chip, but it doesn't include the allophone synthesizer (SP0256) so unless you have an allophone synthesizer this won't do you much good. --Chuck (29 years ago, 7-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Mars rover
|
|
Having seen pictures of the Mars rover I am intrigued as to the mechanics of it. Does anyone know of where to get any details of such things as drive system and suspension. I don't have a few million dollars to make one but there may be some useful (...) (29 years ago, 7-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: Mars rover
|
|
just attack it with legos.... once you figure it out with legos, it's pretty easy... having looked at it my self... i would assume that only one of the wheels (per side) or all are driven, but the suspension system is very simplistic... infact, i (...) (29 years ago, 8-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Mars rover
|
|
(...) Well, the wheels are each driven independently by an internal motor. The rocker-bogie suspension is self-evident, but of course it works best if the wheel and motor sit out at the ends of the suspension. That means six motors. (...) I haven't (...) (29 years ago, 8-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Problems with my motors
|
|
Hi my handyboard works fine, but i have a big problem with my motors. If i use the "FD(x)" command my motor runs very well. If i use the "motor (x,100)" command my motor haven4t enough power and both led (green + red) flash. It4s a motor from a (...) (29 years ago, 8-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Corrupted or Invalid Pcode?
|
|
I have been using the Handyboard successfully for over 6 months. Recently I've decided to mount it on my robot base. After all the dust settled last night, I powered up the Handyboard. Since I put the batteries elsewhere on the robot, I put a keyed (...) (29 years ago, 9-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | ICB loading problem
|
|
I'm trying to load a short ICB file (compiled using Newton Labs web server). Everytime I try loading it (I am stripping the CR in the file), I get a: Loading timer2a.icb. Fatal internal error: .s19 file was not contiguous What am I doing wrong (I (...) (29 years ago, 10-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | IR connection
|
|
Hello, I attached a Radio Shack IR emittter / detector to the handyboard to cure my touch sensor faults I'm using the Legobug. The problem is that chair legs fit between the sensors and don't trigger the switches. The IR sensors are mounted on the (...) (29 years ago, 10-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR connection
|
|
(...) Hi, You should plug the detecvtor into a digital port. (...) (29 years ago, 10-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR connection
|
|
(...) Howdy- I put mine into the analog ports, but not directly- here's how I do it- +Volts o | / R1 \ 47K / \ | "Analog" Out R2 1K | >------\/\/\-------o---...---> | Sensor In --- C1 --- 10uF | | ----- --- - You may discover that you need to alter (...) (29 years ago, 10-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Sourcecode of pcode_hb.s19
|
|
Hi! I'm looking for the source code of pcode_hb.s19 because I like to replace the motor driver source. Do anybody have or know where to find the source code? Thanks tom (29 years ago, 11-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sourcecode of pcode_hb.s19
|
|
(...) go to the Software Resources page ... look for link titled "Interactive C Source". -Fred (29 years ago, 11-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: Corrupted or Invalid Pcode?
|
|
I've discovered the problem. When I mounted the Handyboard, I used metal standoffs. When the board is mounted, it doesn't work. When it isn't, it does. The solution then I guess is to use nylon washers to isolate the Handyboard from the standoffs. (...) (29 years ago, 11-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Corrupted or Invalid Pcode?
|
|
James, Thanks for following up. The reason for this behavior should be fairly evident -- there are traces very close to the mounting screw holes. Your metal washers must have shorted them together, affecting wires to the memory. I do mention to use (...) (29 years ago, 11-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Pulse outputs??
|
|
I need help on understanding the motor controller circuit. Looking at the source in the lib_hb librariy it looks like different pulse trains are sent out to increase the average output voltage by poking increasing values of 256 into the rught (...) (29 years ago, 11-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | enable_cheesy_encoders
|
|
I've tried the enable_cheesy_encoders and it doesn't seem to work for me either. What I get is 0 for the portX_shaft_count all the time. Is this what you're getting? I've looked at the code but I couldn't see why it wouldn't work. Were you or anyone (...) (29 years ago, 11-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | rug warrior board
|
|
I am trying to wire up a rug warrior board, and i think i have thecomputational hardware all set up correctly. I have been over my wiring as best as i can and cant fina a problem. Here is what it is doing. I can download the p code interperter ok, (...) (29 years ago, 11-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | rug warrior memory
|
|
I think i am still having trouble with the memory on my home brewed rug warrior board. I am using a 68hc11a1fn chip. I completely rewired it and i am positive it is wired correctly, however i still cant get the pcode to run. It will downlod (...) (29 years ago, 13-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | rug warrior memory
|
|
config should be set to 0x0c, not 0x0d. let us know if that works. -fred (29 years ago, 14-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | 68hc12?
|
|
I'm currently assemblying a handyboard and came across some literature for Motorola's 68HC12 microcontroller. The one thing that attracted me to it is its built in memory-mapping capabilities. Do people generally find the handboard's 32K limiting? (...) (29 years ago, 14-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re:rug warrior memory
|
|
Mike, My HB does similar things and to fix it I just turn the board of and then on again without leaving ic(shareware v) and it generally sychronises. Joe Martin Email:joema@mpx.com.au ---...--- (...) (29 years ago, 15-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | [Fwd: Announce: ColdFire Discussion List]
|
|
For those of you who haven't heard, Motorola is currently offering a deal on the ColdFire Evaluation board. The board comes with 4Mbytes of DRAM (in the form of a 1Mx32 SIMM) and 256KB of Flash ROM (two 128KB Flash ROMS), two serial ports, a (...) (29 years ago, 15-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | [Fwd: Announce: ColdFire Discussion List]
|
|
The coldfire kit looks like a good deal. Does anyone know what the pSOS, C compiler and debugger cost if you wish to purchase them after the 60 day demo period? (...) (29 years ago, 15-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Mars Rover
|
|
Can anyone direct me to a good site where i can get info about the sensors, behaviors and other mobile robotic aspects of the mars rover... Thanks Sriram (29 years ago, 15-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | HandyBoard newsgroup...
|
|
I'd like to know how to get on the handy board newsgroup and also would like any ordering information on the Microprocessor 68HC11. Thanks, Mr John Anderson (29 years ago, 15-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: HandyBoard newsgroup...
|
|
(...) I got mine from BG Micro (www.bgmicro.com/800276-2206) but I wasn't too happy when my CPU and static ram came in the same, non-static guarded, non-foam inserted, plastic bag. I've also been looking for a 86HC12 vendor but haven't found any. (...) (29 years ago, 16-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | serial light steady on
|
|
I have completed the charger/serial board and it checks out Ok except for the fact that as soon as the host serial cable is plugged into the board, the green serial light is steady ON. The voltage between pins 2tx and 7gnd is -12V. I thought this (...) (29 years ago, 17-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | back-ordered from DMS/Prabal Dutta?
|
|
Hi everyone, I have been receiving word of people having orders 8 to 10 weeks old with Digital Micro Systems/Prabal Dutta that have not been filled. I would like to assess the situation more generally. If you presently have items back-ordered at (...) (29 years ago, 17-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Unsubscribe
|
|
Unsubscribe me, Please. Thank you, -- Daniel Blakley HP Roseville Ntwks Div 916-785-8759 (29 years ago, 17-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | assembling I/C board
|
|
Hi, I've encountered some problems assembling the interface/charger board. After installing the 16-pin socket for U16 and the capacitors and then mounting the MAX232 chip, I then applied power to the board. But, the PWR LED did not lit up and the (...) (29 years ago, 18-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: assembling I/C board
|
|
(...) Well, if the power LED didn't light, then you don't have power to the MAX232 chip (unless the LED is installed backward or broken). It sounds like you've already skipped ahead without passing the first set of tests, which I've copied from the (...) (29 years ago, 19-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | assembling i/c board
|
|
Hi, Is it normal for the i/c board PWR led to not glow too intensely?...cause my PWR led is not glowing that brightly compared to my serial led. Before my PWR led did not glow at all until i resoldered some joints that look like it needed more (...) (29 years ago, 20-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Voltage
|
|
Hello all, What is the max. voltage I can run through the handyboard. I have a 12v dry cell battery that I would like to use. If I can use a 12v battery, can I change the transformer to the handyboard charging/serial unit? Also, I am looking for a (...) (29 years ago, 20-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: assembling i/c board
|
|
no, it should be just as bright. make sure you use the special low-current HLMP LEDs as specified. normal LEDs won't work right. -Fred (...) (29 years ago, 20-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Voltage
|
|
(...) 12v is fine. you could up go to 18v or so w/o problems. you might not even need to change the adapter. if the yellow charge LEDs light, then the batt is charging ok. it will be slower than the original pack but maybe that is not a problem for (...) (29 years ago, 20-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Com port trouble with IC
|
|
I recently bought a Handy Board which works fine, but my version of Interactive C wants to communicate with the board via COM1 only. The port I have available, without completely changing my computer setup, is COM3. How do you get IC to change ports (...) (29 years ago, 20-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | LM34 temp sensor to handy board?
|
|
I've got on my desk here a National Semiconductor LM34 temperature sensor. It outputs a voltage corresponding to 10mV/deg F. So, if it's 78 degrees F in the room, I get a voltage of .78V. I'd like to hook this device to an analog port on my handy (...) (29 years ago, 20-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Geting Started?
|
|
Hi everyone, I am fairly new to robotics/electronics and was wondering how to get started with the HandyBoard. So what is the best way to get started? I already know how to program more or less in C and a little in C++ can you program the Handy (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: LM34 temp sensor to handy board?
|
|
It sounds like you just want a standard non-inverting amplifier. wire an op amp like this: |\ sensor------|+\ | >-+-analog input of 6811 +--|-/ | | |/ | +----R1-+ | R 2 | GND where R1 and R2 are chosen such that (R1+R2)/R2 is the gain you want, in (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Geting Started?
|
|
Why don't you start by perusing the web site... pretty much all of your questions are answered there. The site's home URL is (URL) in particular: * the FAQ * the "get your hands on a handy board" * the software resources page * the tech docs page (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: LM34 temp sensor to handy board?
|
|
I tried the circuit out tonight, and it works! (Mostly.) I hooked up a 1K and a 3K resistor for R2 and R1, for a gain of 4, and the output is roughly linear with the input. Still need to do some more testing. I ended up having to use a +/- 12V (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Serial Communications.
|
|
I am considering using two MiniSSC II servo controllers from Lynxmotion ((URL) to control the servos on a six leg walker using the handyboard as the CPU. The only problem is that the MiniSSC uses asynchronous serial communication. Is it possible to (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Servo control using Miniboard slaved to Handyboard.
|
|
As an addition to my earlier message I have a cheaper and possibly more versatile way of controlling the servos. I have obtained information on the Servo16 algorithm by Erik de la Iglesia which runs on a MC68HC11E1 (he mentions using the E9 but the (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Servo control using Miniboard slaved to Handyboard.
|
|
A friend of mine built a radio controlled walker with six legs using twelve servos and a single BASIC stamp to control the walking. The stamp accepts the PWM from the RC receiver (using the pbasic 'pulsin' command) and outputs the pulses to all of (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: Serial Communications.
|
|
Thanks for the info. I would like to see the code and wiring diagram if that's possible. Thanks for the help. John Hatton. (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Exp Board ETA?
|
|
I was wondering whether there was an estimated date for the availability of the said expansion board for the HB... there is a design and schematics for a proposed Exp Board on the web site from February and I remember a thread of discussion and (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | FW: Serial Communications.
|
|
Hi John: I've used the HB to send serial command strings to a Mini SSC (for the Lynxmotion arm). I built a tiny daughterboard with a MAX232 that plugged into J6 on the board for power. Software handshaking is minimal and the MiniSSC works fine. If I (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: FW: Serial Communications.
|
|
Mike -- Doesn't the Mini SSC have a TTL-levels mode, making the MAX232 unnecessary? Please send your serial output code, though. that would be good to distribute. -Fred In your message you said: (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Servo control using Miniboard slaved to Handyboard.
|
|
Using the Miniboard as a servo slave is a good idea, perhaps even easier is to use a BOTBoard since the BOTBoard doesn't have any motor drivers hooked up to it (no PCB modification required.) Using the MiniSSC is "ok" but for controlling multiple, (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: FW: Serial Communications.
|
|
Hi Fred: The Mini SSC does have a TTL-mode, but it needs inverted data i/o mode. Rather than figuring out how to do that in s/w I just used the MAX232 because it was easy and it made debugging easy into a dumb terminal program on my PC. I've had (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | LCD display
|
|
Hi there, I'm in the midst of ordering all of the parts necessary to assemble the Handy Board. However, I'm having trouble finding two parts. They are the following: Description Catalog No. Manufacturer ---...--- ---...--- ---...--- Infrared (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: LCD display
|
|
Hi. Give me the location and phone number to this place that you can order them and I will consider ordering several and selling them off individually. Scott sherman@plains.nodak.edu CSG ITS NDSU (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: LCD display
|
|
(29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Servo control using Miniboard slaved
|
|
Chuck: I agree with you; what I've done with the MiniSSC is to break the path into a set of linear segments with via points in joint space. The lynxmotion arm ends up needing a lot of points (therefore moving pretty slowly) to avoid jerkiness, but (...) (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | headers
|
|
This may sound like a dumb question, but I don't know where to get headers. Digi Key has some but 4 different kinds. The parts list says nothing except 14 pin female header. Nothing else. Where did you get your headers and what are the part numbers? (29 years ago, 21-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: LM34 temp sensor to handy board?
|
|
Jeff, I used a couple of the 10mV/deg Kelvin ones, with nothing more than the current load resistor, ie no amplification at all. For example, freezing point = zero celcius = 273 Kelvin = 2.73 volts. With the 6811 resolution of about 20 mV (5v / (...) (29 years ago, 22-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: LM34 temp sensor to handy board?
|
|
(...) of (...) accuracy. What is the maximum temperature that the LM34 will 'read' ? Thanks Chris (29 years ago, 22-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: LM34 temp sensor to handy board?
|
|
(...) Depends on the specific version of the LM34, I believe mine can read between -50 to 300 degrees Fahrenheit. ---...--- Jeff Keyzer UCSD EE Major jkeyzer@ucsd.edu (URL) (29 years ago, 22-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Obtaining the Handyboard in the UK
|
|
Does anybody know if it is possible to get the Handyboard in kit form or assembled in the UK. The problem with ordering from the USA is that customs charge taxes/duty on goods over ?145 ($237 approx.) which increases the cost. Thanks in advance for (...) (29 years ago, 22-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Obtaining the Handyboard in the UK
|
|
<bold>John Hatton, writes: </bold><x-quoted>The problem with ordering from the USA is that</x-quoted> <x-quoted>customs charge taxes/duty on goods over ?145 ($237 approx.) which</x-quoted> <x-quoted>increases the cost. </x-quoted> In Canada custom (...) (29 years ago, 22-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | FW: Obtaining the Handyboard in the UK
|
|
I don't know if Patrick sent this to the list but just in case here is his mail regarding the Handyboard in the UK. (...) (29 years ago, 22-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | i/c board as battery charger
|
|
Hi, I've just succesfully assembled the hb kit i got from Digital Micro and attached it to a 2 wheel differential drive chassis. I'm very pleased with the handy board, but it's been a bit annoying when i'm downloading pcode and it takes the board a (...) (29 years ago, 22-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Converting servos + other stuff
|
|
hello, Yall! I'm trying to find a good source for motors, but to no avail.Has anyone tried using modified servos, as described in 'mobile robots'(Jones and Flynn)? It seems kind of expensive, but these appear to be pretty good quality stuff. (...) (29 years ago, 23-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Converting servos + other stuff
|
|
(...) Servos work well, but are constrained to relatively light robots (less thana three pounds. You can use them on heavier robots if you install a bearing axle for the wheels and just use the servo to drive the wheel. Basically the servo wasn't (...) (29 years ago, 23-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Obtaining the Handyboard in the UK
|
|
I have check with Customs & Excise in the UK and they say that there is no ?145 limit so obtaining the board from Hong Kong seems like a better idea and getting the enclosures from the states on their own (the charger needs to be obtained in the UK (...) (29 years ago, 23-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Load Capacitance of the 8MHz crystal?
|
|
Salutations, all, I'm putting together a couple boards, and Mouser has (unfortunately) discontinued the part number listed in the parts list. There are, however, several 8MHz crystals of an appropriate size in the catalog, but I don't have an old (...) (29 years ago, 23-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | New list member
|
|
Just wanted to introduce myself as a new mailing list member. I've been reading the archives for a while, but my workplace only got the mailer working correctly to external locations yesterday. Anyway, I got my HB a while ago from Digital (...) (29 years ago, 23-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | 2nd line of display
|
|
I was wondering how to access the 2nd line of the display directly. In my application I would like to update the bottom line without changing the top line. Anyone know any way to do this? Any other info on direct positioning of the cursor? Thanks, (...) (29 years ago, 23-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: New list member
|
|
Regarding your problem with the jack on the serial line getting hot and melting (uh oh), I believe it is because the HB and Mini-SSC serial lines aren't quite compatable. If you're lucky, you might be getting data through (random coincidence?), but (...) (29 years ago, 23-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Spi distances
|
|
I want to connect various handyboard in a ring configuration, and i think do it via the SPI port. I need aprox. 50 meters between handyboards.Can the SPI support that distance ??? If don't how i can do that. Any help be beatifoul. Thanks in (...) (29 years ago, 24-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Smoking serial/charger board...!!!
|
|
Well, Today I dig up my handyboard which was working fine with the serial/sharger board and all the last time I used it a few months ago. After a fresh overnight NiCd charge using the onboad power connector (i.e. not using the serial/charger board), (...) (29 years ago, 24-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: New list member
|
|
In response to David's post about using the Mini SSC 2 boards and producing a walking robot (my aim is a 12 servo 6 legged walker) I am writing to provide the information that I have found. I have posted a similar question to David about the MiniSSC (...) (29 years ago, 24-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Which 68HC11x1xx
|
|
Hello I want to build a Handy-Board. Now I saw, that I can use several different 68HC11 Processors. In the partlist is the 68HC11A1FN, in the assembly instruction the MC68HC11E1FN in some pictures in the same instruction a picture with the (...) (29 years ago, 24-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Smoking serial/charger board...!!!
|
|
make sure you have a telephone-style and not network-style RJ11 cable. Here is how you tell if you have a telephone-style or network-style RJ11 cable. Hold the two ends together, metal contact side up, as if you were trying to plug them into each (...) (29 years ago, 24-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Which 68HC11x1xx
|
|
'a0 is an earlier and discontinued version of the 'a1. 'e1 has some different features than the 'a1 but is almost identical for HB purposes. 'e1 has a little more internal RAM (which isn't really used by Interactive C) and some more flexibility on (...) (29 years ago, 24-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Which 68HC11x1xx
|
|
(...) Fred, Where can one find info on the A1 vs E1 differences you mention. This is not in the 68HC11 reference manual (pink book). Thanks, Clay Timmons ctimmons@asic.sc.ti.com Dallas Personal Robotics Group www.dprg.org (29 years ago, 24-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: Which 68HC11x1xx
|
|
If you look in you 68HC11 Reference manual in sections 2.1.1 to 2.1.5 there is a description of the differences and there is a table showing the memory sizes for the different types (by the way the table misses the 8K ROM in the MC68HC11A8 entry in (...) (29 years ago, 24-Jul-97, to lugnet.robotics.handyboard)
|