To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1101 (+100)
  Re: FW: IMPORTANT; BEWARE (fwd)
 
(...) DELETE (...) VIRUS (...) for (...) Not quit right. There is a virus that work with adding a special character through email. And if it look with specific terminal, the terminal will accept that character as an special command (may be can (...) (30 years ago, 11-Dec-96, to lugnet.robotics.handyboard)
 
  Motor output circuit in HB.
 
I was taking a look at the schematics for the HB motor output circuit in order to see how could I fit it to work with the h-bridge in the RC Fast Traxx I have. Thanks to people in this mailing list, I know that in I have 4 signals in the Fast Traxx (...) (30 years ago, 12-Dec-96, to lugnet.robotics.handyboard)
 
  Questions on Search Patterns with Polaroid & IR
 
With Handyboard, and the book "Mobile Robots", we want to use two Polaroids (50-60 KHz) for long range detection/target acquisition and short range IR (40 KHz) for a. Close in target pickup b. Target avoidance when an object has been captured and it (...) (30 years ago, 12-Dec-96, to lugnet.robotics.handyboard)
 
  A Rotating (Sweeping?) Polaroid "Dish"? Can it work?
 
Rather than fix one of our Polaroids, we want to put one on a rotating platform in front of the vehicle so instead of turning the vehicle to search for targets, we can stop, sweep the sonar back and forth, find a target, and turn towards it. (...) (30 years ago, 12-Dec-96, to lugnet.robotics.handyboard)
 
  Fw: IMPORTANT; BEWARE (fwd)
 
---...--- (...) doing -bs (...) jeff@wombat.eng.fsu.edu, (...) mhaik@wombat.eng.fsu.edu (...) DELETE (...) VIRUS (...) FORWARD (...) FRIENDS, (...) (30 years ago, 12-Dec-96, to lugnet.robotics.handyboard)
 
  laser diodes II
 
Hi, I am still looking for information on what type of laser diode would work for sensing objects. Any info or opinion would be helpfull. Has anyone tried using laser diodes for detecting objects? I would be interested in finding out how they were (...) (30 years ago, 12-Dec-96, to lugnet.robotics.handyboard)
 
  RE: laser diodes II
 
Any laser diode will work for sensing objects. The trick is that they are _so_ bright that you can't just look for the reflection (unless your are sensing objects at a few hundred feet) There was a Circuit Cellar contest entry which used a laser (...) (30 years ago, 12-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Replacing Motor Driver 754410's
 
(...) Scott The 18200's are a pretty staight forward upgrade. I'm currently using two of them to run a couple power widow motors from a 12V gel cell. They work great. They get hot pretty quick, so a heat sink is a definite must. Scan through the (...) (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
 
  Replacing Motor Driver 754410's
 
Hello! I'm looking for feedback on my proposed modification of the HB. I need to drive a 2amp motor with 24 volts. I don't really trust the 754410's to handle that much power (not to mention the handyboard traces). What I'd like to do is replace (...) (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
 
  12V batteries
 
I need a source for a good 12V battery. I'm thinking gel cell to keep the weight and size to a minimum. I found a 12V lead acid at Radio Shack, which is a good size but it's too heavy. My current needs should be modest - a couple of stepper motors (...) (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Replacing Motor Driver 754410's
 
(...) I concur here, I have a 6inch X 6inch piece of aluminium for 2 of them, and this seems to dissapate all the heat I am generating. I could see longer runs or steeper grades would require a larger heatsink. (...) I was the one who originally (...) (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
 
  10 or 12 bit A/D?
 
Hello, I am interested in a 10 or 12 bit A/D version of the Handy Board. Does anyone have any information that might assist me? Thanks in advanced. ���...���Bye, ���Kevin Hollander Kevin Hollander Univ. of New Mexico Dept. of Mechanical Engineering (...) (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
 
  Handy Board supplier ?
 
I am new on this list and I wander if anybody can help me with information about a supplier of 'Handy Board' with a reasonable price; the ~$280 it's excessively high for me. Thanks Gyuri (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
 
  Polaroid Sensors
 
Hey Everybody, Quick question for you. Just bought two Polaroid ultrasonic ranging modules, and I would like to know if I must use the Propulse batteries and holder that the manual suggests. If not, does anyone have any suggestions for a substitute (...) (30 years ago, 13-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Polaroid Sensors
 
The HB power source will work. Plug the power lines into the +5v and GND anywhere on the HB's headers. (...) (30 years ago, 14-Dec-96, to lugnet.robotics.handyboard)
 
  Sonar and encoder conflict.
 
I am attempting to run the following routine on my Handyboard int check() { int inches; ping(0); msleep(35L); inches=sonar_time/150; printf("%d \n",inches); return inches; } The program runs great and returns the proper value (Thanks to the software (...) (30 years ago, 15-Dec-96, to lugnet.robotics.handyboard)
 
  steppers - HB
 
Wondering if anyone knows of a good way to interface a couple of steppers to the HB AND if there are any ic routines written to control steppers. Ideas, comments, suggestions, questions welcome. Bruce (30 years ago, 16-Dec-96, to lugnet.robotics.handyboard)
 
  Good Times virus warning!
 
Sorry, I can't help myself. I have a 102 deg fever right now and I am not thinking straight. -Fred ------- Forwarded Message <<Subject: Final warning about the "Good Times" virus>> READ THIS: Goodtimes will re-write your hard drive. Not only that, (...) (30 years ago, 16-Dec-96, to lugnet.robotics.handyboard)
 
  Handy board parts
 
I am searching for HB parts such as the 32K static CMOS ram p/n 62256-100LP, voltage monitor, p/n DS1233-10, IR demodulator p/n IS1U60, motor driver p/n L293, RS232 converter p/n MAX232CPE, or any acceptable substitutes. Would appreciate anyone (...) (30 years ago, 17-Dec-96, to lugnet.robotics.handyboard)
 
  Getting started
 
Hello to all, I am a senior in High school and I would like to get into robotics. I bought "Mobile Robtics" and have read parts of it. Is the Handy Board a good place to start? I would really like to get into some AI later. Does anyone have any (...) (30 years ago, 17-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Getting started
 
(...) I think that the Handy Board could be a good next step, depending on what you want to do with it. There are many similarities between the controller board discussed in "Mobile Robotics" and the Handy Board. Perhaps one of the more important (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Handy board parts
 
(...) I got the following at JDR ( (URL) ): HM62256LP-10 $4.69 DS1233 $1.79 MAX232CPE $1.89 I got what I hope is a good substitute for the IS1U60 at Radio Shack, it is their p/n 276-137 and was discussed in the book "Mobile Robots" in similar use. (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  Re: steppers - HB
 
I haven't tried this on a handy board, I am using a miniboard, but I think the process is similar: not having a lot of time to figure out how to use dc motors with my miniboard (my project deadline was coming up fast) I decided to use step motors (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Handy board parts
 
(...) ectronics (...) Richard Hughes and Ben Wirz sells onesies of the L293D. See the "Get Your Hands on a Handy Board" page. -Fred (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  JAVA and the handyboard
 
Has anyone looked into putting JAVA on the Handyboard? I keep hearing that JAVA was originally designed for embedded systems and I am curious if it has the ability to live within the Handyboard's resources. Thanks ---...--- Lance Keashly Glenayre (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  testing the CPU
 
i am currently assembling the board, and i am not sure where to hook up my logic probe to test the CPU. will someone please help me? thanks. -mretzlaf@isd.net (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  RE: JAVA and the handyboard
 
It won't fit by a wide margin. I was part of the original Java team and when it was called 'Oak' it was designed to be as compact as possible with a kernel footprint at around 100K. (fit in a single 128KB eprom) But now that it is not just for (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  Re: JAVA and the handyboard
 
(...) I believe the predecessor to Java (known as "Oak") may have been designed for embedded systems. But last time I looked, a Java Virtual Machine took 8 MB of memory, which won't exactly fit into the HC11 address space :-) Really, if you want a (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  (senior design)
 
My design team and I just recieved our Handy-Board. We plan on building an autonomous mobile robot that will run a search program and (hopefully) locate a 4" x 4" wooden(passive) block. The domain that it will search in is approx. 15' x 15'. We plan (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  Re: JAVA and the handyboard
 
(...) What about building an IJ (Interactive Java). You loose all the cool stuff, but then again, there isn't much for graphics on the handy board. At least you get some decoupling (object orientation), and perhaps Java is a little easier to learn (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  RE: JAVA and the handyboard
 
Didn't someone (William Lim?) write a paper about BALI, a small version of JAVA, that could be used for small mobile robots? I have a reference to his paper at home, but if someone can post it to this group quicker, it might be interesting. -- Clint (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  Re: (senior design)
 
(...) No problem. The motors are turned on, and you can forget about 'em, until you want to stop. Read sensors, do other math, and the robot will keep going. (...) Very fluid. Turns will be an issue, you will have to work that out. (...) He is (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  Interactive C sample routines
 
Is there anyone out there that would have some IC routines that might get me started writing my own. Something for controling two motors, bump sensors, and IR sensors. Really anything that will give me a general idea of the direction I want to go (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Interactive C sample routines
 
(...) Bill: In addition to the IC Manual, check out the URL below: (URL) used these materials to get my students started. Also, see some code examples in the IC Libraries directory (that comes with IC). Check out the Chapter on Robot Programming in (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  RE: JAVA and the handyboard
 
Found this about Bali after doing a web search: (URL) contains an abstract about a paper presented at an SPIE related conference. It seems to refer to using JAVA and extensions called BALI to provide a development environment for boards like the (...) (30 years ago, 18-Dec-96, to lugnet.robotics.handyboard)
 
  Handy Board Crash
 
Hi, I was installing another user knob beacuse the other one broke. While I was in the middle of doing it, I think I fried the board. When I start up I have an led sequence like this: green green green red does anyone know what this means, if so (...) (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Handy Board Crash
 
(...) I'm assuming you mean the motor LED's and that they stay on and nothing shows up on the LCD. Sounds like you didn't disconnect the battery and accidently shorted it. Probably lost the contents of the RAM. Try reloading the Pcode. hope it works (...) (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  Newcomer
 
Hello: First - thanks for all the good information that we were able to find on the handyboard web page and on the associated ftp site. My son and I have decided that we would like to build the handyboard rather than buy one ready-built. We have no (...) (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Newcomer
 
(...) either. some people like the e1 better because it has more flexible timer and counter lines. but the a1 has a simpler bootstrap sequence and is less likely to have compatibility problems with the host computer. (...) No, it's harder than this. (...) (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Handy Board Crash
 
(...) Re-load pcode_hb.s19. If the board loses its operating program, when it starts up it runs gibberish, and the value of the motor output latch is randomized. -Fred (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Newcomer
 
(...) The E variant can handle 4 IC lines and 4 OC lines, while the A must do 3 IC lines and 5 OC lines. The IC and OC lines are the way the processor handles timer-sensitive signals, such as RC signals. The Handyboard can handle up to 2 ICs and 2 (...) (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  (Polaroid quandry)
 
Kind of in a jam... Have heard conflicting advise (thaks again to everybody who bothered to give it)...My design group wants to come to a decision about powering our two Polaroid Ultrasonic tranducers.... * One set of opinions has advised that we (...) (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  RE: JAVA and the handyboard
 
I found my info on the Bali paper: Title: The BALI Development Environment for Small Mobile Robots Author: Willie Lim, Future Minds, Inc., William Y-P. Lim, wlim@ai.mit.edu Pages: 11 Presented: Mobile Robots X Conference (SPIE Conference 2591) in (...) (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  RE: JAVA
 
The IC package is quite impressive. What's the expectation of a JAVA-like language? --Jerry (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  Bali papers?
 
Has anyone had any luck in reading the PS files on Bali? My Ghostview v1.5 on HP-UX gives many errors. (30 years ago, 19-Dec-96, to lugnet.robotics.handyboard)
 
  stepper motors
 
Hi all, I want to control 2 stepper motors with my handyboard. I want to do microstepping for high resolution. I already have a couple of vexta unipolar(6 wire) steppers. I also have the TI Sn754410 H-bridge chips. I now understand the need for (...) (30 years ago, 20-Dec-96, to lugnet.robotics.handyboard)
 
  Re: (Polaroid quandry)
 
(...) Yes, you can use the +5v regulated power bus to power the ranging module. That's all the power you need for a Polaroid US system. (...) That's 2500 mA. (through the power lines of the renging module) At least that's what the specs say. Who (...) (30 years ago, 20-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Bali papers?
 
(...) I noticed both the PS files had a strange character at the beginning of the first line and the last line. I wasn't able to print the files until I removed the strange chars. -- Clint (30 years ago, 20-Dec-96, to lugnet.robotics.handyboard)
 
  RE: JAVA and the handyboard
 
There is another paper in SPIE Mobot Robots 11...I'll put that on the MIT AI ftp site when I get back from vacation (1/2/97). Willie (30 years ago, 20-Dec-96, to lugnet.robotics.handyboard)
 
  chip selects:
 
Perhaps I have just overlooked this in the documentation for the HB and IC. Is there an easy way to control the chip selects Y*? Are they memory mapped or harder to get to than that? Thanks for the info: patrick (30 years ago, 21-Dec-96, to lugnet.robotics.handyboard)
 
  Re: chip selects:
 
(...) They are memory-mapped. See Appendix B of the 6270 Robot Builder's Guide, in the Tech Docs area, for info. -Fred (30 years ago, 21-Dec-96, to lugnet.robotics.handyboard)
 
  mailing list, unsubscribe
 
Thank you for my time on your mailing list. Pressure of commercial work makes it impossible for me to keep up, so please remove me from the list. I look forward to being able to read it again some time in the future. Thanks, Terry, a.k.a. (...) (30 years ago, 22-Dec-96, to lugnet.robotics.handyboard)
 
  serial port
 
Hello, I'd like my handyboard to communicate with my PC through the serial port. Since I am not a RS 232 specialist, I am looking for code on the PC side. I am using Visual J++ and/or Visual C++ under Windows 95. Thanks for any help. Laurent (...) (30 years ago, 23-Dec-96, to lugnet.robotics.handyboard)
 
  Workin' its little heart out?
 
Hi, all... A generic 68HC11 question- I (sorta) got my code running this weekend. I'm trying to get a 68HC11E1 to operate all 4 OC and IC lines on interrupts. I have about 800 instruction cycles spread over 8 interrupt routines. The waveform I'm (...) (30 years ago, 23-Dec-96, to lugnet.robotics.handyboard)
 
  RE: Workin' its little heart out?
 
The trick is to make sure that if you get simulataneous interrupts you services them both before returning. ---...--- From: Mike Ross[SMTP:mross@outl....nasa.gov] Sent: Monday, December 23, 1996 12:59 AM To: handyboard mailing list Cc: TRP mailing (...) (30 years ago, 23-Dec-96, to lugnet.robotics.handyboard)
 
  no download mode
 
I spilled coffee on my handyboard this morning - it was powered off at the time. There was liquid across several pins on the 6811, though. I removed the 6811 and cleaned it up, then reinserted it. Now, both red&green LCDs come on when I turn it on. (...) (30 years ago, 23-Dec-96, to lugnet.robotics.handyboard)
 
  Re: no download mode
 
(...) Mine was doing what sounds like exactaly the same thing... Try replacing you MAX 232 chip if nothing else works, I blew mine out (god knows how) a while ago, and was acting like you said. Just a suggestion :) -Wes (30 years ago, 23-Dec-96, to lugnet.robotics.handyboard)
 
  Polaroid pinouts
 
Hi I've just received my Polaroid sonar stuff, but there's no documentation ! (of course Polaroid appear to have closed for Xmas.....) Does anyone have the pin assignments for the 6500 series Polaroid sonar module. The connector is roughly in the (...) (30 years ago, 23-Dec-96, to lugnet.robotics.handyboard)
 
  (Polaroid Pinouts)
 
Scott, The J1 connector has the following pin assignments: pin 1 GND pin 4 INIT pin 9 V+ pin 6 OSC pin 7 ECHO pin 8 BINH pin 2 BLNK (30 years ago, 24-Dec-96, to lugnet.robotics.handyboard)
 
  (no subject)
 
Sorry, my E-mail address is realy: ameba@email.mcleod.net -thanx (30 years ago, 24-Dec-96, to lugnet.robotics.handyboard)
 
  E-mail Address
 
My e-mail is going psycho. just to make sure, my email address is:: ameba@mcleod.net -thanx (30 years ago, 24-Dec-96, to lugnet.robotics.handyboard)
 
  Assembling the HandyBoard
 
Hello all: We got the handyboard assembly kit from Digital Micro Systems. We are putting it together now. Everything has gone well. Thanks, the instructions are really good. A couple of things have not worked quite right: 1. Couldn't find the 2.2M (...) (30 years ago, 25-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Assembling the HandyBoard
 
(...) You need that resistor to stabilize the crystal frequency. Try Radio Shack if it is missing from the kit. It doesn't have to be 1/8 watt, 1/4 or 1/2 watt is fine, just make sure it is 2.2 megaohm. (...) So far so good. (...) There is probably (...) (30 years ago, 26-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Assembling the HandyBoard
 
(...) I was getting similar behavior with my board. It wasn't clear to me that pins 2 and 3 in the serial cable from the PC to the interface board should be switched. Credit goes to Mike Ross for helping me figure this out. Once I switched these two (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Thanks, Fred
 
Fred, Thanks for giving us this great design. I appreciate it and I enjoyed building my Handy Board from a kit. I do have two corrections, though. No big deal, just typos. In the on-line assembly instructions, J15 is referred to as J14 at one point, (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Assembling the HandyBoard
 
(...) The whole issue of null (inverted) connections vs. straight-through is incredibly confusing, because you must take into account the gender of the connector (male pins or female pin sockets) in determining whether it is a null connection. Start (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Assembling the Handyboard
 
Hello all: We saw the recent message, same sub. We got our handyboard from Digital Micro a couple of days before the holidays. We had a great time building the boards. The kit is excellent. The instructions are great - even for novices like us. (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Hey, it works!
 
I can hardly contain my glee! After 3 weeks of fun-yet-obsessive, marriage-threatening, Xmas-be-damned behavior, I've got all four IC and OC interrupts going, receiving/processing/outputting 4 RC PWM signals. This is only a side-note for Handyboard (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  sending signals over power lines
 
hello. While this question doesn't pertain directly to the handyboard, I thought I would post it here since I am using the handyboard in my project. Some of you may have heard of this product: There are devices on the market (radio shack and a few (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  RE: sending signals over power lines
 
There is a good write up on this in one of Steve Ciarcia's columns in BYTE magazine some time in the early 80's. A quick stop at the periodicals desk of a technical library might help you here. --Chuck ---...--- From: Andrew S. (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Re: sending signals over power lines
 
(...) There are a bunch of proposals along these lines (eia standards, and future standards) CeBus, LonWorks. X-10 is most prevelant, somewhat limited, and some of the stuff sold is of marginal quality, although some is really good. X-10 is what you (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Re: sending signals over power lines
 
(...) Whether the signal is traveling over AC or DC does not matter. What type of current is running through the wires is unimportant. What is important is that your electical wires *already run all over your house*. What these devices are (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Re: Polaroid pinouts
 
I forgot who...someone over here said that they put up scans of the Docs on his hompage or somthing like that. Anyonre remeber something like this? (...) (30 years ago, 27-Dec-96, to lugnet.robotics.handyboard)
 
  Re: sending signals over power lines
 
(...) Andrew, I've putzed around a bit with the system you've discribed. Its called X-10 power line carrier transmission. (P.L.C.) The codes format was setup back in 1978 for Sears and Radio Shacks Plug 'n Power system. Since then X10 Powerhouse has (...) (30 years ago, 28-Dec-96, to lugnet.robotics.handyboard)
 
  Assembling the handyboard - ic3b1
 
We have completed building the board. As mentioned in an earlier note, we are using the beta version of Randy Sargent's IC. Here is some experiences: - extremely easy to use. Fun. - thanks for a great product. Some things are not that smooth - may (...) (30 years ago, 28-Dec-96, to lugnet.robotics.handyboard)
 
  HELP! Handyboard ALMOST works.
 
Stuff that works: IC loads fine 1+2; returns 3 printf("Hello World!"); works LOAD MUSIC.C works {looney_tunes();} plays the tune but then.... LOAD TESTBRD.C Gives a page full of undefined functions. LOAD DIAG.C Gives several pages of undefined (...) (30 years ago, 31-Dec-96, to lugnet.robotics.handyboard)
 
  Using RC cars for robot
 
Hi everyone, Beleated merry christmas and happy new year.... I would like to find out from those of you who have recently or are presently using RC cars with their handy boards for robots. 1. What type of vehicle did you use? 2. How did you handle (...) (30 years ago, 31-Dec-96, to lugnet.robotics.handyboard)
 
  RE: Using RC cars for robot
 
(...) Chicago Models International "M1A1 Abrams" tank Radio Shack "Wild Cougar" (Nikko America 'Shredder") Radio Shack "Scorpion Tracks" (...) Conveniently :-) I pick only RC cars where I can drive them with differential steering. (...) I've built (...) (30 years ago, 31-Dec-96, to lugnet.robotics.handyboard)
 
  Re: HELP! Handyboard ALMOST works.
 
In your message you said: (...) Sorry, testbrd.c and diag.c have nothing to do with the Handy Board. They are part of the older 6.270 board distribution. Get the hbtest.c program from the Handy Board software pages. -Fred (30 years ago, 31-Dec-96, to lugnet.robotics.handyboard)
 
  interfacing to RC cars
 
I haven't interfaced RC cars to a handyboard, but my experience might help anyway. (...) Tyco "Fast Traxx" and a look-alike made by Nikko. Both have dual treads (and therefore differential steering). Both are very fast. Unfortunately, both are (...) (30 years ago, 1-Jan-97, to lugnet.robotics.handyboard)
 
  Re: Using RC cars for robot
 
(...) We have successfully integrated a Traxxas RC car with the Handy Board. The vehicle uses a standard servo for steering and an electronic speed control (same behavior as a servo.) Since the HB can control 2 servos this works well. In this case (...) (30 years ago, 2-Jan-97, to lugnet.robotics.handyboard)
 
  pcode downloading
 
Happy New Year! I'm putting together a HandyBoard and am stuck at the point where pcode_hd.s19 is downloaded. Some details: Have a chip labled SIPEX SP232ACP as a substitute(?) for MAX232. During downloading using DLM the board syncs OK but (...) (30 years ago, 2-Jan-97, to lugnet.robotics.handyboard)
 
  Problem Downloading Pcode!!!!
 
Hi, I'm really stuck. I got a facory fresh HB, instead of a Motorola it had a Toshiba C11W chip. When dowloading pcode_hb.s19 IC Win 95 says "CONFIG register required resetting. Please place in download mode again." Help, my scince project is due in (...) (30 years ago, 2-Jan-97, to lugnet.robotics.handyboard)
 
  Coparison of Sensors
 
Hi, I know this is probably a stupid question to you, but I wrote a program to compare sensors. But it doesn't seem to work. Can anyone help?? Here it is (30 years ago, 2-Jan-97, to lugnet.robotics.handyboard)
 
  Re: pcode downloading
 
Here is the relevant part of the test instructions: Finally, the MAX232's ability to transmit data to the host computer is tested. Again using pin 7 of J9 as a ground reference, measure the voltage at pin 3 of J9. This is the MAX232's serial output. (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Re: pcode downloading
 
(...) : (...) I get -8.9v when its not jumped. When jumped I get some floating values in the mV range. I checked all of the solder joints. Changed power supplies. Removed and reseated the chip. Checked power and continuity at various points around (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Re: pcode downloading
 
(...) OK, well I think it is isolated at the pseudo-MAX232 chip. Did you get the +10 v power supply pin on the p-MAX ok? It's at pin 2. Measure it w/r/t ground and you should get +10v. Before you order a real Maxim, check the polarity of your (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Config 0C / 0D
 
Hi, I know this is an old chestnut but believe me I have searched the mail archive and nothing quite matches what I'm seeing. I have a handyboard which I made and which seems to work perfectly. However, I have to download (using hbdl) with the (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Re: Coparison of Sensors
 
(...) Looks like you got too many semi-colons. Take out the semi-colons on all the while lines where you want the while to do the following thing. The process is getting to the "while(!start_button());" line and staying there. Also you have too many (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Re: Coparison of Sensors
 
(...) I agree. You should only have a semi-colon after a while if you dont want that while to loop through any instructions. A semi-colon after a while tells the compiler that all you want to do is continuously test the while condition until it (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Re: pcode downloading
 
(...) Yep, that checks out. (...) I get the correct voltages for the caps. And if the wrappers are on correctly they should all have the correct polarity. I ordered a replacement MAX232CPE (not the high speed "A" version). Hopefully this will either (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Got V2X working...!
 
Recently I posted a request for help in interfacing the 68HC11 to the Vector 2X, and through the help of readers of these groups, thank you very much, I was able to get it running. It was quite persnickety, with many possible modes of operation, so (...) (30 years ago, 4-Jan-97, to lugnet.robotics.handyboard)
 
  Handyboard Parts
 
Well here I am again. I have gotten all my parts except the microprocessor (MC68HC11A1FN), the IR demodulator (IS1U60), and the 32K static CMOS RAM (62256-100LP). I have tried Jameco for the RAM but the Jameco part number 42833 doesn't seem to be (...) (30 years ago, 4-Jan-97, to lugnet.robotics.handyboard)
 
  Returned mail: Service unavailable
 
----- Transcript of session follows ----- <<< HELO media.mit.edu <<< MAIL From:<brose@ipa.net> <<< RCPT To:<jwright@seattleu.edu> <<< DATA <<< QUIT mail: /var/spool/mail/jwright: cannot append mail: cannot open dead.letter 554 (...) (30 years ago, 4-Jan-97, to lugnet.robotics.handyboard)
 
  Re: Handyboard Parts
 
(...) The MC68HC11A1FN is available from BG MICRO. ( (URL) ) The 32K static ram is available from JDR. ( (URL) ) (30 years ago, 5-Jan-97, to lugnet.robotics.handyboard)
 
  Rayovac Renewal batteries
 
Hi, I was wondering if anyone has any info on the Rayovac Renewal batteries. According to the packaging, they're rechargable alkaline batteries. Sinch alkaline lasts longer that NiCd batteries, I was wondering if it would be good to use these (...) (30 years ago, 5-Jan-97, to lugnet.robotics.handyboard)
 
  Re: Rayovac Renewal batteries
 
Renewals are pretty cool -- they are "true" alkaline in the sense that they have the same voltage, discharge curve, and shelf life. The only bugaboo with them -- and it's a big one -- is that each *cell* must be individually charged. so you can't (...) (30 years ago, 5-Jan-97, to lugnet.robotics.handyboard)
 
  HB - fast sensor reading
 
Hello, I have a clock signal of 5 kHz and an analog signal. (There are in total 128 clock pulses) I need to read in the analog signal every time the clock signal is high. So I need to read the clock signal with at least 10 kHz. I tried this with IC, (...) (30 years ago, 6-Jan-97, to lugnet.robotics.handyboard)
 
  I think I fried my board!!
 
I need help figuring out what I did to my handyboard. I had it all assembled, tested, and working when one of the battery leads touched one of the solder spots on the board. A small puff of smoke rose from the board but I was able to disconnect the (...) (30 years ago, 7-Jan-97, to lugnet.robotics.handyboard)
 
  Re: I think I fried my board!!
 
Keith, We'd be happy to send you a new inductor to try out. Let us know how it works out. Best of luck! (...) - Prabal (30 years ago, 7-Jan-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR