 | | Re: Somewhat C challenged.
|
|
Victor, The peek(0x1000) statement returns the byte at memory location 1000 (hex). In C, the '&' operator is a bitwise AND. So, what you are doing is ANDing 4 and the contents of 0x1000. What's really going on is you are interested in only bit 3 (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | IR in programs
|
|
How would I use an if/then statement if I used the onboard IR reciever? Earlier, I downloaded a program that Max Davies wrote to determine the different variables for my remote. In the readme file, it says that the rules are set by a command like (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | voltage divider
|
|
could the voltage divider circuit shown in the Mobil Robots book (page 116 fig5.20b) be implemented as is OR does the built in pulldown resistors cause it to be modified. Thanks for all the brain dumps, victor (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | NOTE 04/10/97 10:50:15
|
|
Hi, Can someone help me understand encoders.asm? This is what I deduced from the code and I'm wondering if my guess is correct. 1. When TIC3 and TIC2 inputs are changed, an "interrupt" in execution occurs and and execution immediately jumps to the (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: IR in programs
|
|
(...) Here is a simple example of how to do 'different things' when you press various buttons on your remote. If you press digits, they are displayed on the LCD. If you press rewind, the LCD is cleared. When you press stop, the program ends. If you (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Looking for a good microcontroller.....
|
|
Hi, This question doesn't really belong to this mailing list, but since some of you know quite a lot about microcontrollers I thought maybe someone could help me. I'm working on a project about A Management System for an Optical network. Therefore (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Parts substitution
|
|
I have a question on the replacement of the a specific resistor. On the handyboard there is a 3.83K 1/8W resistor. I just received in the mail the last pieces for the board and was shipped a 3.83K 1/4W resistor. Is the wattage citical on this (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Parts substitution
|
|
(...) I believe the wattage just tells you how much power the resistor can reasonable dissipate. Therefore using a transistor which can dissipate more power than what the design calls for is alright, but using one that dissipates less power is bad. (...) (30 years ago, 10-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Bots on TV - Nice IR app
|
|
So, I saw the Scientific American show on PBS and I was completelly geeked! It was too short. I was most impressed by the tennis ball capturing contest and by Newton Lab's Vision Car entry. Cognachrome is very cool. After seeing the show I logged on (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: voltage divider
|
|
Hi Victor, I believe you mean "built in pull up" resister on HB. Yes, you need to take 47k pull up register into accound for the voltage devider circuit. -Pandit ---...--- (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Looking for a good microcontroller.....
|
|
If you can use an I2c chip, then the Motorola MC68HC11E2 has 2k of EEPROM and costs about 8-10 dollars. You can try contacting Motorola for samples if you are a student I have heard they are free. You need a school letterhead signed by a proffessor. (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: your mail
|
|
No, you can't use PWM outputs that swing from about ~10v-~4v for *digital* output. However, you can pull the 74HC374 (see motor output schematic) out of socket and put a 16pin ribbon cable(rat shack) in the socket. Then take the other end to a (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Bots on TV - Nice IR app
|
|
I said (...) You asked (...) (URL) are developing a version of IC for commercial release and are linked via the HB page's software resources page. J (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re:
|
|
(...) yup, it was too short! (...) Phil, couple of questions for clarity. Does it need to go up and down the steps or just up? does it carry stuff? Why is step climbing needed? It might be easier to make a wall climbing bot...or a bot that can leap (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Hi, fellow (ro)Botters! Did anyone watch Scientific American Frontiers on Wednesday? If not, or even if you did see it, check out www.pbs.org . PLEASE SEE IT! there's a lot of good links, a complete transcript, and other goodies. But now, onto my (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: pressure sensors... non-conductive foam
|
|
(...) What a neat idea! Sounds nice and compact and simple to build too. Do you think it would also be viable to use a soft NON-conductive foam and then measure the capacitance instead of the resistance to work accurately with lighter pressures? (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: pressure sensors... non-conductive foam
|
|
Max> Do you think it would also be viable to use a soft Max> NON-conductive foam and then measure the capacitance instead of Max> the resistance to work accurately with lighter pressures? Actually this will work better. I built a grid sensor using (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: BotS on TV
|
|
As usual, this mundane matter of workin for a living has interfered yet again with the more pleasant pursuit of robotics (read: missed the show). Was this a PBS show? I would love to have seen this. Does anyone know when this might be shown again? (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | HB files
|
|
Help! I can't open any of the files at the cherupkha site. I presume these are "postscript" files. I've tried various apps to view them without success. I'm workin in a PC enviroment, no MACS or unix. I keep readin about the great libraires out (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re:
|
|
(...) Now _this_ is a challenge. Presumably you've read the treatment on step climbing robots in Marvin Weinsteins "Android Design" ((URL) is out of print but still in libraries. It takes a _lot_ of energy to move up stairs. Basically you robot has (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB files
|
|
Postscript files are generally for printing out. Therefore, you send a postscript file to a "postscript printer". Most HP Laser Jets are. Otherwise, you can use a program called GhostView. It's a viewer that has postscript capabilities. I think it's (...) (30 years ago, 11-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | HB books
|
|
Hello, Does anyone know what books are avaible about building robots with the HB as microcontroller? Thanks Emiel Agema (30 years ago, 12-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Parts substitution
|
|
(...) In this case, no problem. The computation of power is simple... Watts = Volts X Amps and ohms law is... Volts = Resistance X Amps Using the traditional I = current (they say it comes from the French word for Intensity) R = Resistance E = (...) (30 years ago, 12-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | sencdr0.asm
|
|
In the program sencdr0.asm, what does the line: BRCLR ADCTL,X $80 * for? Thanks for any help. :) ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The (...) (30 years ago, 12-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: pressure sensors... antistatic foam -Reply
|
|
(...) That's exactly the stuff. I saw a demo of this in class, so I can't give you specifics, but it's the sort of experiment that takes about 6 minutes to try on your own. Note, however, that there are a few different kinds of the foam: i mean the (...) (30 years ago, 12-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: your mail
|
|
I once saw something like this, but it was very complicated to build. There were TWO separate arrangements of your wheel descriptions, and they were hinged from a set of "hips". I believe this is because, as wheel 1 is pivotting over the front edge (...) (30 years ago, 13-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | HB Simple Encoder Routines
|
|
Hey everyone, My partner and I are trying to use the sencdr?.icb and fencdr?.icb routines to keep position measurements of a robotic arm. The encoders are break beam and provide a signal of 4kHz max. We used 4 J-K flip flops to reduce this frequency (...) (30 years ago, 13-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | My Robot, "JERK"
|
|
To those interested: For those who are interested, I have posted pictures of robot at URL = (URL) it isn't totally complete, the construction is, for the most part finished. It is mobile and can almost traverse the maze it was designed for. Thanks (...) (30 years ago, 13-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Fried analog port
|
|
I was taking some measurements of sensors by reading the value on the LCD display. Suddenly poof a burst of smoke came from the analog port (0). Now the only reading I have on that port is 1, but the other ports are fine. Could I have somehow fried (...) (30 years ago, 13-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: sencdr0.asm
|
|
Yes, but why? Is the contents at ADCTL+X supposed to change? ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of (...) (30 years ago, 13-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | RE: HB books
|
|
Mark Robillard has written 2 good books on robotics. No one has mentioned these books here before, so I though I would list them. Here are the 2 book titles : * Microprocessor controlled robotics * Advanced microprocessor controlled robotics These (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | QFP sockets
|
|
Hi, Thanks for the response on finding a microcontroller. I have 1 little problem left: if I'm going to use a Motorola 68F333 or the somewhat cheaper 68HC916Y1 I need a conververter from 160-lead QFP (.65 pitch) to an "normal" pinout where I can (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: NOTE 04/10/97 10:50:15
|
|
OK, I haven't looked at encoders.asm but if the following doesn't help just send more questions. (...) Sounds about right. (...) TCTL2 sets rising, falling, or both edge modes; TMSK1 arms interupts; IC event sets the TFLG1 register. (...) correct (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | motor routines in lib_hb.c
|
|
Does anyone know why these eight speeds were chosen in lib_hb.c for the motors and what would happen if the code were re-written to allow any speed between 0 and 255? int _speed_table[]= { 0b00000000, /* speed 0 */ 0b00010001, 0b01001001, (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: motor routines in lib_hb.c
|
|
(...) These 8 bit masks are the most symmetrical way to to organize speeds of 0 through 7/7. You could rewrite the code to accept a byte and use that as the mask, but unless you think it would save space, it's a waste of time. The miniboard routines (...) (30 years ago, 14-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: motor routines in lib_hb.c
|
|
(...) Think of them as repeating binary waveforms (they are clocked out the 'enable' pin of the motor chip at 1Khz) so on an oscilloscope speed 2 (third entry) would appear.. time -> 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 (in mS) Vmotor : +--+ +--+ (...) (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: motor routines in lib_hb.c
|
|
If I'm not mistaken, (someone please corect) those speeds represent the actual shape of the waveform. Let's list some details. 1. Each bit 0 or 1 represents 0V or 9.6V. (or whatever external source) 2. Each bit represents the above voltage for a (...) (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | line following
|
|
Hey all, I'm looking for some ideas on sensors and algorithms for a line following robot (black tape on white floor). If any of you have had some luck at this or know where I can find some info please let me know. Thanks Rajesh (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Expansion interface.
|
|
I have a question about the expansion interface. If it is decided upon the 1Amp 9V transistors...would it be a problem for the HB's 1Amp Voltage regulator or the fuse? (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | store variables in RAM after reset
|
|
Hi guys, I'm new to the interactive C. Does anyone know how to declare an array of variables which can be changed by the program and stored in the RAM and their values stay the same even after reset? Second, I'm aware of something called the (...) (30 years ago, 15-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Hardware Problems
|
|
Hello, I'm having trouble getting my Rev 1.2 Handy Board up and running. It did work once and then the following symptoms: I start the mac based down loader, which download the bootstrap code fine. Both charger board and the handy board's serial (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
(...) He have (had?) some robots here at work that were used in the production areas, and they followed a line on the floor. I've not studied them carefully, but I think they work something like this: Two reflective photosensors are aimed at the (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
(...) This one's pretty easy. Two IR detector/emitter pairs along the bottom, midline of the robot (say, about 1cm or less off the floor). The algorithm is to keep both detectors over the black tape (i.e. a low reflectance reading); if the right one (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Hardware Problems
|
|
(...) All I can add is that is what mine does, and it seemed to break when I hooked up a 'normal' 12V battery charger, which is opposite polarity to the HB charger requirements. According to the diodes in the diagram, this shouldn't be a problem, (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Battery life
|
|
I think I already posted this question some time ago but never got an answer. Is it normal to have the HB run out of battery even when is not being used ?? I know the battery is always working to keep the RAM from erasing, but I'm wondering how long (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Battery life
|
|
Same question here. I left mine turned off for one night and the next day the battery had almost completely run down! jm (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
(...) I did something like this in an early computer engineering course. The requirements are exactly the same ie. follow a black line. What Chris said is a good start but you should also consider the case when the turn is too sharp; In this case (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Battery life
|
|
Ive got a pretty crappy answer for you but its the best I can offer; check out how much current the RAM draws from a data sheet and calculate the power it uses (P = IV, where I=RAM current, and V=5v). Divide the mWHr your battery delivers by the (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Battery life
|
|
rabbit> 3600 since there are that many seconds in an hour. I myself rabbit> have left the handyboard off for periods of 4weeks or more rabbit> and still have had my memory. I just rattled the above off rabbit> the top of my head so, anyone, please (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Battery life
|
|
The best answer would be to take the mAH of the battery, say X=1500 mAH. Find out the current drawn by the RAM say I=5mA. Divide X by I and you get the number of hours of battery life. This is ofcourse assuming that you have a fully charged battery (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
(...) <snip> (...) <snip> In my rather limited experience with reflective photosensors, I've found that black on white is not always the best of choices -- the white can come up as different numbers depending on how clean/dirty the floor is and the (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Battery life
|
|
To avoid that battery problem, I have mine plugged in about 20 hrs/day and the other 4 hrs the serial interface is plugged in. I've had problems in the past where I've presented a robot that couldn't work because the batteries died & there were no (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | variables
|
|
Can you access variables declared in a binary progam from a different binay program? i.e. can "speeda" (pcode.asm) be accessed by xxxxxx.asm? Do you have to know the actual address where "speeda" is stored or can you just use "speeda" inside (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
(...) As have I, so when I wanted to build a line-follower, I used a couple of IR detectors in concert with a pair of IR emitting diodes. They were arranged on the nose of the robot as follows: 1 2 3 4 \ | | / Where 1&4 are the IR emitters and 2&3 (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
(...) The experience is good, I'm just not sure you took away the right lesson from it. :-) Everything Katt say's is true, when you are following lines detecting the line is sometimes not as straight forward as the description would have you (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Small gear suppliers?
|
|
We need some small gears for a gear train for a small DC motor. Does anyone know of likely vendors? I want decent quality gears, not plastic! Thanks. ***...*** * Greg Starr, Professor and Graduate Advisor * * Department of Mechanical Engineering ph (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | gears
|
|
Hello all, There is a company called Small Parts Inc. located in Miami Lakes, FL. They have been a good source for me in the past for all kinds of random stuff. I don't know if they have the specific parts you need, but they are a good shot, and at (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Small gear suppliers?
|
|
Try. Stock Drive and Sterling. (516) 328-3300 ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of Science and Art (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | battery life
|
|
(1) the memory should last about a month if the board is turned off, as several have noted. (2) please be aware that the serial interface will *DRAIN POWER FROM THE HB* if the interface itself is not plugged into power. thus do not expect anywhere (...) (30 years ago, 16-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | line following
|
|
I have had great success with black tape on many different light colored backgrounds but I wasn't using discrete components for the sensors and emitters. Instead, I used Omron EE-SY313 amplified infrared photosensors, and plugged them right into the (...) (30 years ago, 17-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: line following
|
|
Chuck, Chuck, Chuck...not EVERYONE in engineering and robotics is male. I, myself, am quite definitely *not*, nor ever will be, male. Engineering is a co-ed field, and women have made their mark upon it. While there are few of us compared to the (...) (30 years ago, 17-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | battery life and charging
|
|
Did someone already try to program the handy board the way to enable it testing the battery´s status and - if necessary - driving to a "docking station" and reloading the battery? (Self-feeding-automatism) Someone an idea how to solve this problem (...) (30 years ago, 17-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | When will the expansion board come out?
|
|
Hi, does anyone know when the expansion board will be available? Thanks, Duncan (30 years ago, 18-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | motor driver chip....
|
|
hola, I was planning on using the L293D motor chips in a project that I'm working on. I'm going to use polaroid motors to drive a vehicle. I was wondering: -Does anyone know how I could get specs for this chip? -Are there other motor chips that (...) (30 years ago, 18-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Good books about electronics
|
|
Hi! I'm very new in this business. So I thought where could I get a good tutorial book about electronic components and the way they work. And most important - what is electricity and how it works. Can anyone advise me? mike (30 years ago, 18-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: motor driver chip....
|
|
see the hb suppliers page for dealers who sell the l293d. (URL) your message you said: (...) n. (...) (30 years ago, 18-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Good books about electronics
|
|
By far the best book for all kinds of electronics is "the art of electronics" by Horowitz and Hill. There is not a lot of "what is electricity" (try a good encyclopedia). This book begins with basic network theory and goes from there through just (...) (30 years ago, 18-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: motor driver chip....
|
|
(...) Depending on the manufacturer, you might be able to get the specs online, usually in the form of PDF files that are the datasheets for the chip. I know national semiconductor does this, and it's very fast and easy...otherwise, you have to try (...) (30 years ago, 18-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: motor driver chip....
|
|
SGS-Thomson makes the L293D and L293E: www.st.com/stonline/...s/1330.htm You can also build a custom H-bridge motor driver using the MAXIM 620&621 MOSFET drivers. Search for Maxim in a search engine. jm (...) (30 years ago, 18-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Good books about electronics
|
|
The ISBN is: 0-521-37095-7 I took the class at harvard that the book was written for. It was a good class. I learned a lot. I'm not so good with the analog stuff though... There is a student manual which is pretty helpful too. It's by Hayes and (...) (30 years ago, 18-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Stepper motors driver circuit and .s19 compiler...
|
|
Good Day All, I also would like more info on this. If not too much trouble, could it be posted to the whole board as well? Take care... (30 years ago, 18-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Stepper motors driver circuit and .s19 compiler...
|
|
Hi, I heard from fred that there is someone out there who had used stepper motors with the handyboard, I am doing something which need to use stepper motors. Therefore I need your help in this area, please email me how should I go about design the (...) (30 years ago, 19-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Stepper motors driver circuit and .s19 compiler...
|
|
Hi, I heard from fred that there is someone out there who had used stepper motors with the handyboard, I am doing something which need to use stepper motors. Therefore I need your help in this area, please email me how should I go about design the (...) (30 years ago, 19-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | hbsonar
|
|
I am trying to run 4 sonar sensors from the HB, and I'm not sure how to go about doing this. I have a copy of the code from the ftp://cherupakha.med...ntrib/kent directory, but I'm pretty bad with assemby language and I'm not sure what I would need (...) (30 years ago, 19-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | motors
|
|
Hi, I have some motor trouble. I have two motors. I have a polaroid sonar. When I run one of the motors, the sonar works. When I run the other motor, the sonar's detected distance jumps arround randomly. The randomness seems to be more at higher (...) (30 years ago, 19-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: motors
|
|
I haven't had the same poblems, but I have a theory as to your problem. There are two probabilities: 1) The motor is causing too much noise and is interfering with the sonar, or 2)The motor is giving off electrical noise (i.e. electromagnetic waves) (...) (30 years ago, 19-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Using Step-Motors
|
|
A couple people have expressed interest in how to use step-motors with their handyboards. I have used step-motors with my miniboard, and since both the handyboard and the miniboard use two L293D chips to run the motors, I am fairly confident that (...) (30 years ago, 20-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | GPS
|
|
Hi, I want to connect a gps-receiver which provides NMEA-0183 data to the HB. Did anyone connect a gps to the HB before? Carsten (30 years ago, 21-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: motors
|
|
Mar, You might want to try attaching a small (0.1uF) capacitor to the motor leads as close as possible to the motor. Use a ceramic or monolithic ceramic capacitor. That might reduce the motor noise your sonar board sees. Also remember that even (...) (30 years ago, 21-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Handyboard to Vector 2X compass
|
|
I'm planning to hook a Vector 2X digital compass to my HandBoard. I'm looking for any code for such and interface. It should be simple SPI stuff but I've never messed with the SPI before and would rather not re-invent the wheel. I've checked the web (...) (30 years ago, 21-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re[2]: motors
|
|
Thanks. I tries that. I even tried to use four of them in parralel. OK, here's what I've discovered...just to let you all in on it and maybe it'll help someone in the future. I pulled the leads from the motor header and powered the motors directly (...) (30 years ago, 21-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: GPS
|
|
(...) Yep. Me! There weren't any major headaches involved in doing it. Feel free to ask me questions. I may have to get my source from home in order to answer them though. Curt Mills, WE7U Senior Methods Engineer/System Administrator (...) (30 years ago, 21-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Good books about electronics
|
|
(...) Mike, I would also recommend the book: "Electronics (A Self-teaching guide)" by Harry Kybett (1986 by John Willey & Sons) ISBN 0-471-00916-4. It is a very excellent beginning text. It teaches concepts and then you self test yourself every 2-3 (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Collision Advoidance Emitter Circuit
|
|
Hi All, Had anyone actually built the Infared LED emitter circuit that is on the Rug Warrior? (i.e. pg 108 of Chapter 5 of the book "Mobile Robots" by Jones and Flynn). I've looked at it and I can't for the life of me figure out how it works. Before (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Polaroid Sonar
|
|
Help! I've purchased the Polaroid Sonar OEM kit, plugged them in in accordance to Kent's instructions and using his software, but if I plug in BINH through a 360 Ohm resistor or with no resisitor, all I get is 1 - 2". If I unplug it, I get (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | parts???
|
|
I wonder where o where i can get the 32K ram chip and CPU for my handy board. I have e-mailed Gleason Research and Digital Micro Systems, and they do not respond to me! Anyone have any other ideas, i would appreciate them :-) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Collision Advoidance Emitter Circuit
|
|
(...) Yes, i have. (...) And: "Yep, it works" (little noisy though) Something particular you want to know? Hans (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Collision Advoidance Emitter Circuit
|
|
Hi Gordon, When you mentioned about "doesn't have a ground in it", are you refering to the part the drives the LEDs, right ? If so, the explaination of the circuit is that when the output of the inverter that connected to a 100 ohm register goes low (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Polaroid Sonar
|
|
I was getting the exact same result when I ran motors with the HB while using my sonar. The problem was that there was alot of noise caused by my motors...apparently electrical and EMI. Do you have alot of components that may be causing some noise (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | hb serial connection
|
|
Hi, I recently purchased a handy board kit, and while assembling it, ran into some "download" problems. After the memory chip and LCD were installed (Section 6.0.4 and 6.0.5 of the assembly guide) and I tried to download the IC file (dl (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | I have a good schematic to post
|
|
I have finally debugged my IR proximity sensor circuit and I want to post it to the group. My question is what is the best way to post it? I can put it into a JPG file but I don't want to just send it to the whole group at once. Fred, can this go on (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re[2]: Good books about electronics
|
|
Speaking of good books: It seem the majority of books you can pick up is on "ideal" electronics. The "ideal" transistor, the "ideal" op-amp, the "ideal" circuit! What about a book that tells you when you should put a capacitor of XuF across Vcc and (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: I have a good schematic to post
|
|
Hi Keith. Send it to me and I'll post it for all. Please send as a GIF not JPG as this is better for line art & text (i.e., a schematic). I can decipher just about any encoding format so use whatever's easiest for you. -Fred In your message you (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | serial connection
|
|
Hi, I am still trying to get the PC-Handyboard connection to work. I got as far as downloading the pcode_hb.s19 file successfully. After I turn the main board power off and back on (reset), I should get a message on the LCD screen ("Interactive-C v (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Handyboard to Vector 2X compass
|
|
C> I'm planning to hook a Vector 2X digital compass to my HandBoard. C> I'm looking for any code for such and interface. It should be C> simple SPI stuff but I've never messed with the SPI before and C> would rather not re-invent the wheel. I've (...) (30 years ago, 22-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Handyboard to Vector 2X compass
|
|
OK everyone. I put Tom's stuff online, see the HB HP (handy board home page :-). -Fred P.S. Tom, check your color table the next time you make a GIF. Somehow your black and white schematic GIF got saved with 256 colors (255 blacks and 1 white), (...) (30 years ago, 23-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Proximity sensor circuit on the web!
|
|
I have posted the circuit to my web page about ten minutes ago. The address for the page is in the sig. file at the bottom. Follow the robot link near the top of the main page for the schematic. Tell me what you think. Keith Keith Soldavin (...) (30 years ago, 23-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
AN OPEN LETTER TO PROFESSORS JAKE MENDELSSOHN AND DAVID AHLGREN, ESTEEMED FOUNDERS OF THE TRINITY COLLEGE FIRE-FIGHTING ROBOT COMPETITION. Wed Apr 23 00:50:42 1997 Dear Jake and Dave, Thank you for organizing such a fantastic robotic event. It was (...) (30 years ago, 23-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: serial connection
|
|
(...) Your LCD is bad. Either the logic to it is in error (check for an open on the E pin) or the LCD itself is non-functional. If IC cannot talk to the LCD it won't run. (30 years ago, 23-Apr-97, to lugnet.robotics.handyboard)
|
| |
 | | IR In
|
|
Are there any software to allow the handy board to receive input from 3 different IR receivers? I have check the HB web site but what is there only allow input from 2 IR receivers. I need to use the IR receiver to check for the presence of an IR (...) (30 years ago, 23-Apr-97, to lugnet.robotics.handyboard)
|