To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4501 (+100)
  RE: Wireless Link to HB
 
Dave, I have been doing radio communications between my HB and a remote sensor but I am sure you could use the same radios for communicating with a PC at up to 2400 bps. I have been using an Elsema transceiver coupled with an FSK modem chip. (...) (28 years ago, 5-Oct-98, to lugnet.robotics.handyboard)
 
  Yeeee Haaaa! and Will this motor work?
 
Hi all, Yeeee Haaaw! I just got my HB in from Gleason Research Friday and started figuring it out this weekend. WOW! What a blast! It was worth eating peanut butter sandwiches for 3 months to save up for! ;-) This is EXACTLY what I've needed to get (...) (28 years ago, 5-Oct-98, to lugnet.robotics.handyboard)
 
  Serial I/O again
 
Greetings! I need a "good" sample of how to do serial i/o between the Handy Board and a host computer. The host computer I am intereested in is running MACOS (8.X). Here is the scenario: - The HB has an IC program downloaded on it. - The program (...) (28 years ago, 5-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Mindstorms website forums weirdness?
 
Matthew Miller wrote in message ... (...) does (...) Yup. alex (28 years ago, 5-Oct-98, to lugnet.robotics)
 
  Re: Mindstorms website forums weirdness?
 
(...) Hmm. (28 years ago, 5-Oct-98, to lugnet.robotics)
 
  Re: Yeeee Haaaa! and Will this motor work?
 
the "correct" way is to measure their resistance with an ohmmeter. if it's less than 5 ohms, it might be a problem. the "other" way is to just plug them in and turn on the motor outputs. as long as you use full power (not any of the software-reduced (...) (28 years ago, 5-Oct-98, to lugnet.robotics.handyboard)
 
  Re: only 70.000
 
I've been rather suprised about all the media attention and wide attraction it has caused - it's either luck or shrewd marketing.. or perhaps a bit of both. But what better way to get free publicity than to get parents queuing up outside stores for (...) (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  U.S. News Online article
 
An editor at U.S. News sent this URL -- (URL) focus of the article is that LEGO isn't just for kids anymore -- very cool to see the outside world beginning to wake up to this...even if it is in a roundabout way. --Todd (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  Re: only 70.000
 
A few weeks I (and I suspect a few other UK r.t.l'ers) was 'headhunted' by a marketing agency to do some in-store promotion of Mindstorms in well-known high-street shops in the UK, from the middle of October. At the moment MS is only available from (...) (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  No expansion packs in the UK yet.
 
But LEGO UK 'hope to have them by Christmas' Huw (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  finding parts for Handy Board
 
Hi all, I have just got a set of blank P.C.B's from Douglas electronics and now trying to get all the parts togrther to build the Handy Board. I have managed to find all the parts from R.S. components and Farnell Electronics except for the 32Kbit (...) (28 years ago, 6-Oct-98, to lugnet.robotics.handyboard)
 
  Mindstorms on "The World" public radio show
 
Hey, anyone who gets the PRI radio show The World should tune in thursday afternoon. I was just interviewed for what I think will be a lengthy piece on Lego Mindstorms. (Well, I'm sure it'll be on Mindstorms. I'm just not sure how in-depth it will (...) (28 years ago, 6-Oct-98, to lugnet.announce, lugnet.robotics)
 
  Re: Mindstorms on "The World" public radio show
 
(...) interviews! :) --Todd (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  RE: finding parts for Handy Board
 
The PLCC version of the 68HC11 is the one that you want. The part number from R.S. is 265-853 and in the July 97 - October 97 catalog it cost 7.50 pounds + VAT. This price has no doubt increased but the stock number should be correct. The 32K RAM I (...) (28 years ago, 6-Oct-98, to lugnet.robotics.handyboard)
 
  Re: finding parts for Handy Board
 
Russ, From your email address I assume your are looking for parts in the UK. SRAM - I don't have a Farnell catalog around but almost any 32Kx8 SRAM should work. RS part number: 311-007 Toshiba TC55257DPI, 265-465 NEC uPD43256. 68HC11 - The (...) (28 years ago, 6-Oct-98, to lugnet.robotics.handyboard)
 
  Thanks! I found the FAQ and Archives...
 
Thanks all for the motor tips! I've found the FAQ and the Mail List archives...so I shouldn't be asking so many dumb questions. However, since I've checked the FAQ and am have 45 minutes left doownloading the Archives...I have another (...) (28 years ago, 6-Oct-98, to lugnet.robotics.handyboard)
 
  Nevermind...but, What is Normally Open?
 
Ok, I feel real dumb. I could have sworn I didn't see the answer to that last question when I read the printed version of the docs I had. Now, I found the answer at: <<el.www.media.mit.e...dex.html>> I guess I was scanning the text for reference to (...) (28 years ago, 6-Oct-98, to lugnet.robotics.handyboard)
 
  Nevermind Squared...
 
Ok, after reading it for the nth time, I think I understand this statement now: <<The normally open case means that the sensor line is pulled high by the 47K resistor on the Handy Board. The standard software for reading the state of a switch (...) (28 years ago, 6-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Mindstorms on "The World" public radio show
 
(...) Heh. Probably just about the only thing that could convince me to leave my current job. :) (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  difference between stepper & dc
 
hi, I'm doing a robot to navigate it to a destination that needed to avoid obstacle collision along the way. Besides, I intend to use 2 dc motor ( 12v ,0.9Nm, 310mA rating) for the 2 wheels and include the encoder too. Should I use stepper for such (...) (28 years ago, 6-Oct-98, to lugnet.robotics.handyboard)
 
  RoboTag version 0.8 -- explaination & NQC source
 
/* Matthew's RoboTag 0.8 for Lego Mindstorms. * * written in NQC version 0.5b1 -- (URL) * * Copyright (c) 1998 Matthew Miller. You're free to use and modify this as * you wish. You can also redistribute it, but please give me credit and * don't make (...) (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  Mindstorms number
 
I've asked someone to buy a Mindstorms set for me but I couldn't find the box number anywhere. Can someone tell me what's the box number for the main Mindstorms set ? Leonardo (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  Re: who was the 1st non-north american to possess mindstorms???
 
(...) I am only 29, and can remember it. What is even more frightening is that it was 2 **decades** ago. It is bad enough to be approaching 30, even worse when you can remember an increasing number of events that when they occured can be measured in (...) (28 years ago, 6-Oct-98, to lugnet.robotics, lugnet.off-topic.fun)
 
  Re: only 70.000
 
Richard Franks wrote in message <36196BB0.7EDF@__no_...er.com>... (...) Richard, being from Scotland, did you perchance catch the BBC story on it on the B'fast news? I unfortunately had missed it...... ___...___ richard.dee@nospam.virgin.net remove (...) (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  Re: only 70.000
 
Huw Millington wrote in message ... (...) a (...) is (...) I was one of those. Did you take them up on the offer? I was tempted, being paid to promote Lego, but am not willing to sacrifice a day off...... ___...___ richard.dee@nospam.virgin.net (...) (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  Re: Mindstorms number
 
(...) Here ya go... (2 URLs) (28 years ago, 7-Oct-98, to lugnet.robotics)
 
  Programming Language for MS
 
Has anyone heard anything about getting the spec of the RCX code. I would like to find out how it works then write a Java VM for it. Matt Fleming mfleming@objectspace.com (28 years ago, 6-Oct-98, to lugnet.robotics)
 
  Re: Programming Language for MS
 
(...) A bit ambitious. (And not possible until the firmware is fully reverse-engineered, certainly.) You probably could get a java subset working, however. Luckily, you're not alone in all of this. Check out (URL) Matthew Miller ---> (...) (28 years ago, 7-Oct-98, to lugnet.robotics)
 
  Re: Mindstorms number
 
(...) Hi Leo, The 'main' Mindstorms Set is # 9719.... see it at: (URL) have one; and it's *great*! **Maria** (28 years ago, 7-Oct-98, to lugnet.robotics)
 
  Pictures of my old lego robots
 
Hi, I have put two pictures of my old C=64 controlled Lego robots on the web. If you are interested, please have a look at: (URL) comments are welcome. Tom Michiels (28 years ago, 7-Oct-98, to lugnet.robotics)
 
  Re: Mindstorms number
 
Todd Lehman wrote in message <361aaf1b.264755476@...et.com>... (...) show any mindstorms sets :) Maybe you could fix it to search for the theme names. Leonardo (28 years ago, 7-Oct-98, to lugnet.robotics)
 
  Re: only 70.000
 
richard.dee@nospam.virgin.net wrote in message ... (...) they (...) No, but I got them to send me information about the jobs. The promoters should spring up in stores any week now, IIRC. (28 years ago, 7-Oct-98, to lugnet.robotics)
 
  Mindstorms SnooperBot
 
I plan to build a bot that will be able to snoop around into a room (hopefully with people talking about secret things!!!! :-) ), and have it transmit the conversation via a micro FM transmitter. The one prolem is that the bot itself will be quite (...) (28 years ago, 7-Oct-98, to lugnet.robotics)
 
  Current supply
 
Hi all, I am looking for the electrical specification of the 68hc11-family because I want to use one in another application. If someone, any where, this information has, PLEASE SEND IT me!!!!!! Thanks for all. PS: very interesting mailinglist (...) (28 years ago, 7-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Thanks! I found the FAQ and Archives...
 
GDFRITZ@aol.com wrote: <snip> (...) The Handy Board Technical Reference (available for download from the HB web site) shows exactly how to connect microswitches and other sensors to the HB--complete with pictures. It's full of useful information; I (...) (28 years ago, 7-Oct-98, to lugnet.robotics.handyboard)
 
  re: Current supply
 
please see (URL) has pointers to the official Motorola 68HC11 documentation. regards, Fred (28 years ago, 7-Oct-98, to lugnet.robotics.handyboard)
 
  removable rcx
 
Not anything profound here, but just a musing: Next time I build a robot, I'm going to make it so the RCX and sensors are easily removed, so I can leave the basic design together and yet move the brain to another creation. (28 years ago, 7-Oct-98, to lugnet.robotics, lugnet.build)
 
  Re: removable rcx
 
(...) Mmm, good idea... BTW, I wish the batteries were easier to replace...it's too bad they didn't learn that lesson from the 9V monorail boxes. Or maybe if the AC adaptor could recharge batteries inside the unit... --Todd ======== Posted via the (...) (28 years ago, 7-Oct-98, to lugnet.robotics, lugnet.build)
 
  Re: who was the 1st non-north american to possess mindstorms???
 
richard.dee@nospam.virgin.net wrote in message ... (...) Ah, but I posses mine in the ghostly sense, and have done for some time now (whooooo :) (...) Thank you. You're too kind. Moz (28 years ago, 7-Oct-98, to lugnet.robotics, lugnet.off-topic.fun)
 
  Re: removable rcx
 
I have tried that plan but in order to get any strength built-in to my robot I have to get the motors and sensors embedded into the robot or everything just falls off at the first touch. If touch sensors were affordable enough to get some extra, (...) (28 years ago, 7-Oct-98, to lugnet.robotics, lugnet.build)
 
  Re: removable rcx
 
(...) True, that is a limitation. And somehow I have the feeling that my plans will automatically grow to encompass whatever number of sensors and motors I own. (28 years ago, 7-Oct-98, to lugnet.robotics, lugnet.build)
 
  HELP !!! Please...
 
Hi Everybody, Sorry for bugging you all, but I'm desperate for some help... My graphics Display preferences got messed up, and reinstalling the graphics card driver is not fixing it... Last night I downloaded and unzipped (URL) , but while I was (...) (28 years ago, 7-Oct-98, to lugnet.robotics.handyboard)
 
  Extreme Creatures, Cybermasters, etc?
 
Hello All! I'm kicking around the idea (pretty seriously) of finally picking up a Mindstorms, and had a few questions: 1. MS vs CM; are they essentially the same except where the program is stored and executed? If so, what kind of range are we (...) (28 years ago, 7-Oct-98, to lugnet.robotics)
 
  Re: removable rcx
 
Todd Lehman wrote in message ... (...) are (...) I built my last bot so that the Robot frame went around the RCX, but did not connect to the bottom. That way I can pull the bottom off and replace the batteries without dismantelling the bot.. I also (...) (28 years ago, 8-Oct-98, to lugnet.robotics, lugnet.build)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) No, they're actually fairly different. Cybermaster Mindstorms ---...--- Designed for "play" Designed for inventing Two built in motors Two external motors No motor/light outputs (?) Three outputs to wire to motors or lights Three inputs Three (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) Well, I can't give you a complete list of what's in it because I started mixing pieces from it and the basic set almost immediately, but here's a list of some of the pieces: Purple: 2 2x2 medium slope 2 2x2 medium inverted slope 8 2x4 technic (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
"Robert Farver" rfarver@rcn.com wrote in <F0HH9C.29B@lugnet.com>: (...) <snip> (...) <snip of long list> Thanks for the info. Other than the pieces, what's so special about it? Any good plans or programs? Basically, I guess I just don't understand (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  does this list still exist?
 
(28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
Matthew Miller wrote in message ... (...) CM has one general output port besides the internal motors. Eric Brok (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
Besides, the CM cd-rom encompasses an extensive and impressive 'computer game' sort of adventure, with lots of computeranimatons, like a LEGO ISLAND cd-rom title in itself. Very well done; must have been a work of labor for the production team. Eric (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  RE: About the elsema FMTR 2705
 
Michael, I have tried to use the Elsema radios without the modem chips but because 27Mhz is such a noisy frequency (at least here in Australia) I found that I got way to much interference when interfacing directly to TTL. The modem chips are really (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
 
  driving stepper motors
 
Hi all, I have nearly completed building my handy board and have come across a couple of stepper motors that i would like to use to drive my robot. Motor spec's are :- 2 Phase 6V 1.2A 1.8Deg step Is there any way of interfacing the handy board to (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Current supply
 
Hallo Holger, Spezifikationen über die 68HC Familie kannst Du direkt über Motorola beziehen. Ich habe dort das "Pink-Book" kostenlos bekommen, Du must Dich lediglich mit der Literaturabteilung verbinden lassen (Ich habe für die 68HC11A0-A8) das Buch (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) I dunno that much about the technical side of MS or CM. As has been pointed out already, CM is made for playing to a larger extent than MS. I'd still say CM is rather good, though, and quite worthwile. It's probably a good alternative to the (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) They looked interesting in the pictures I've seen. Can you describe them more? (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) Well, there are five yellow wheels on each side, and the tread goes round them. The wheels are probably as large as the medium pulley and one stud wide, with a narrow but deep groove in the center to keep the treads on track. The treads are (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  driving stepper motors
 
Hi all, I have nearly completed building my handy board and have come across a couple of stepper motors that i would like to use to drive my robot. Motor spec's are :- 2 Phase 6V 1.2A 1.8Deg step Is there any way of interfacing the handy board to (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
 
  Re: driving stepper motors
 
Look up the datasheet for the SGS-Thomson L297, they have a complete circuit diagram for a stepper motor driver there. (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) ok, wasn't sure about that. (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) But you could use the treads without, yeah? I'd really like some better treads, as the ones that come in Mindstorms RIS, Tread Trekker, and Mountain Rambler are too small for a lot of things. (Particularly, hard to power and still have a lot (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Mindstorms
 
Hi Fred. I enjoy the listserv, though I am a real novice and don't always understand what is going on. But, I am reading and learning. I just found out that you helped with the creation of the Legos Mindstorm robots, which I have purchased two for (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
 
  pneumatics & mindstorms?
 
I have very little by way of pneumatic stuff; I've mostly avoided sets containing pneumatics. But it seems like there's some interesting potential when combined with Mindstorms. Has anybody made any interesting Mindstorms-controlled air-powered (...) (28 years ago, 8-Oct-98, to lugnet.robotics, lugnet.build)
 
  help on a ADC
 
greetings everyone. im building a digital oscilloscope (to use on a PC) for a project in school but im running into trouble with the ADC im using because it says to use separate grounds and VCC for the digital and analogue parts, but browsing around (...) (28 years ago, 8-Oct-98, to lugnet.robotics.handyboard)
 
  Midstorms Idea
 
I don't have the RIS yet, but I wanted to throw out an idea to see how feasible/difficult a project it would be. In the early 80s I saw games like this in a lot of computer magazines: Two players (bots) would travel around the playfield (sheet of (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Mindstorm and Mac through Virtual PC?
 
Hi there. Has anyone tried to use Mindstorm in combination with Virtual PC or Real PC? Since there is no Mac-version I am interested in this combination. Thanks Rob Visscher The Netherlands ffrob@knoware.nl or rob@fonts-files.nl ======== Posted via (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Re: Midstorms Idea
 
(...) Yes, I've been thinking about that. I might try an' see how well it works running on a whiteboard -- I hate to waste mountains of paper. (Suspected problems: 1 the whiteboard is too shiny 2 the robot treads will muck up the trail.) (...) The (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Re: Mindstorm and Mac through Virtual PC?
 
(...) People have tried it, but apparently there's an issue with the serial port, and it doesn't work. You'll have to use either Robolab or NQC -- hardly a loss, really. (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Automated brick sorter
 
Automated LEGO brick sorter I have built a Mindstorms version of the 8094 mechanical arm that lifts 2x4 bricks and puts them in bins. Of course with Mindstorms, it can actually see what color the brick is and take it to the appropriate bin. It uses (...) (28 years ago, 8-Oct-98, to lugnet.robotics)
 
  Re: Automated brick sorter
 
(...) <snip> (...) I built a different type of sorter that separated red and blue 2x2 bricks. It is not as elaborate as yours, but it was a nice, quick Mindstorms project. Pictures are at: (URL) reply to: dbaum at enteract dot com (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  RE: Wireless Link to HB
 
Dave, Check out Linx Technologies sight at: (URL) have some nice uhf modules that use plain digital levels for input and output. Kevin Kevin Turner klturner@elko-nv.com "You'll never have enough time, money, or memory." (28 years ago, 9-Oct-98, to lugnet.robotics.handyboard)
 
  hi all
 
I'm new to this group, and I'm glad there's place to specifically for robot legos. Visit my page at: (URL) of you here might remember me from RTL. (there's message I posted that I think i THE longest thread I've EVER SEEN) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  RE: Mindstorms
 
Robolab, sold by Pistco-Dacta (Lego educational wing), supposedly supports the MAC. (...) (28 years ago, 9-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) Yes, you can. I haven't tried that, though, so it may very well be that you'll have a hard time trying build a chassis that fits the treads correctly. But it's probably just a matter of adjusting the yellow wheels properly. An interesting (...) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
Matthew Miller wrote in message ... (...) Yup. First thing I did was put the treads on and try to get into the manual control bit. Unsuccessfully, as it turned out. So I watched about 20 min of video, some of which was cool, then discovered that my (...) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  CyberMasters
 
Oh, and I got what I suspect is the first retail one in NZ (the shop had one, rang me specially, and no-one else in Wellington has them yet :) Plus they gave me their spare copy of the promo video for it. Now all I need to do is find a VCR and TV to (...) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
Moz (Chris Moseley) wrote in message ... (...) That's "should NOT be too expensive". Oops. (...) This is very true - you get more cycles as well as more capacity. Moz (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
"Moz (Chris Moseley)" <moz1@ihug.co.nz> writes: Do you have Cyber Master? Cool! Be sure to watch the lego-robotics list, if you aint already. (...) Is this to keep parts of them for later reference? That may be interesting. Personally, I would like (...) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Mindstorms and FM Micro Transmitter
 
(apologies if this appears 2x's) I have uploaded info/specs on the FM micro transmitter that I built for use with my next Mindstorms project. Website:  (URL) to the Lego -> Electrics section ======== Posted via the LUGNET discussion group web (...) (28 years ago, 9-Oct-98, to lugnet.general, lugnet.robotics)
 
  Re: Mindstorms
 
(...) Yes, ROBOLAB works with Mac. Please see my unofficial FAQ for more information: (URL) (...) (28 years ago, 9-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Automated brick sorter
 
Dave Baum wrote in message ... (...) Mine looks distinctly over-engineered compared to yours! (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) :) Yes. I'm waiting to see what the (frighteningly impressive) reverse-engineering people determine -- if I can program (...) Well, I've had my RoboTag robots going for large portions of the day for lots of days (sorry for being vague -- I've (...) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
Moz, I couldn't find this reference in the previous posts: (...) I am I understanding that you have treads that are larger and more flexible than the ones that came with the mountain rambler? I am dying to get something bigger for an pneumatic (...) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  RE: Mindstorms
 
Pls man... don´t ask the mail with handyboard mailing list in the second place !!! My Rules Wizard don´t detect that!!!! I´m tired of clean my input folder!!! thanks... (...) (28 years ago, 9-Oct-98, to lugnet.robotics.handyboard)
 
  Primitive RoboTag movies available
 
If you look at (URL) you'll find a pair of very poorly done AVI-format movies of RoboTag in action. More to come when I figure out how to do it better. (The Linux software is way too slow, and the WinNT stuff is worse. We'll try Win95....) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Re: only 70.000
 
(...) Unfortunately I (ab)use my flexitime way too much to catch Breakfast news :( I've heard from quite a few people who saw things on TV or on the radio though! Sadly enough I wasn't head-hunted or anything! Obviously I'm not good enough! (...) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Re: Mindstorms and FM Micro Transmitter
 
(...) transposition of characters That aside, pretty cool. What's typical indoor range? Outdoor? How long is the antenna and what kind is it? (28 years ago, 9-Oct-98, to lugnet.general, lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
(...) We were talking about the European 8482 Cyber Master set. This has treads that are larger than the mountain rambler ones. Fredrik (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Fred's book
 
Is Fred's book still coming out this fall? (28 years ago, 10-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
Linc Smith wrote in message ... (...) Yeah, CyberMaster ones. (...) Those are still available from Dacta in the US I think, so try the Pittsco catalogue first. Someone here will know more. about that. But be aware that the link-based treads are (...) (28 years ago, 9-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
Moz (Chris Moseley) wrote in message ... (...) I will check out Pittsco! I have always had a hard time finding information about them. I needed a large turntable at one point, and just ended up getting the Log Loader form S@H. I needed some of the (...) (28 years ago, 10-Oct-98, to lugnet.robotics)
 
  Re: Mindstorms and FM Micro Transmitter
 
Have had some troubles with getting the receiver to hone in on the exact frequency (for now its 90.0 Mhz). If the receiver is in a different room, the FM transmitter has difficulties transmitting through walls etc. It needs more juice (only runs on (...) (28 years ago, 10-Oct-98, to lugnet.general, lugnet.robotics)
 
  (no subject)
 
Dear HandBoard list's Members> I am using your Handy Board and I have some questions: 1) I have been trying to use the infrared subsystem. However, i have got some problems. First I load the "sony-ir.icb" and my single program which looks like this: (...) (28 years ago, 10-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Infrared I/O
 
I have done a lot of work in the area of infrared I/O for the Handyboard. My software at (URL) will let you send and recieve codes for a wide variety of remotes. (28 years ago, 10-Oct-98, to lugnet.robotics.handyboard)
 
  Re: Mindstorm and Mac through Virtual PC?
 
Well, I've got a Mac, and ordered Robolab from Pitsco last week. Hasn't arrived yet though. I'm looking forward to using an interface other than the in-box CD-ROM one on a friend's PC. I have never used Robolab, but it was only $25. Pitsco they said (...) (28 years ago, 11-Oct-98, to lugnet.robotics)
 
  Re: pneumatics & mindstorms?
 
I've just ordered a compressor pump, several pistons, valves, tees, and tubing to explore some of possibilities using pneumatics. The first thing that came to mind is the ability to move arms, etc., without the need for limit switches. - - - Nick - (...) (28 years ago, 11-Oct-98, to lugnet.robotics, lugnet.build)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
Linc Smith wrote in message ... (...) Well, you're welcome to email it to me and I'll put it on my page. With pics, even, if I can get a non-expired copy of POV-Ray. Moz (28 years ago, 11-Oct-98, to lugnet.robotics)
 
  Re: Mindstorm and Mac through Virtual PC?
 
Thank Matthew and Suzanne for your info. It safes me a lot of trouble. Please keep me posted on your experiences. Since i’m on the other side of the atlantic (Netherlands) i’ve never seen the mindstorm software. What’s the real difference between (...) (28 years ago, 11-Oct-98, to lugnet.robotics)
 
  Re: Automated brick sorter
 
Huw Millington wrote in message ... (...) Pictures now available at: (URL) (28 years ago, 11-Oct-98, to lugnet.robotics)
 
  Re: Extreme Creatures, Cybermasters, etc?
 
Linc Smith wrote in message ... (...) Hmm. Does Mindstorms count? While I like the extra parts, I bought one for the RCX and transmitter, the other just for the RCX... at $US265 once shipping and GST are included. (...) MS? Fun? Well, yes... :) Moz (...) (28 years ago, 11-Oct-98, to lugnet.robotics)
 
  Please insert 18AA nicads and press any key to continue.
 
Yahoo! I got my Mindstorms at last :-) So I've taken the day off to celebrate. Predictably, I got the CyberMaster set on Friday, and the letter saying I should pick up the Mindstorms on Saturday. It's all happening here, I tell you. So now I use (...) (28 years ago, 11-Oct-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR