 | | using ni-cads in parallel
|
|
Ni-cads have really low internal resistance. If the two packs start off at different levels of charge, you may have a problem with lots of current flowing between the packs when you first connect them. I'd recommend moving to a larger pack rather (...) (31 years ago, 6-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: ni-cads in parallel
|
|
(...) This is generally not a problem. If you get a 7.2v strip of C-cells from a hobby store (this is a 5 cell battery) they can deliver about 150 amps for a short while. You are correct that charging NiCds in parallel has issues. I guess the (...) (31 years ago, 6-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: ni-cads in parallel
|
|
Don't do this. First off, you won't get more current, nicads already can deliver gobs of current, enough to be dangerous. You want more amp-hours, not more instantaneous amperage. Secondly you will have problems with cells charging each other. I (...) (31 years ago, 6-May-96, to lugnet.robotics.handyboard)
|
| |
 | | new project announcement
|
|
"the book of ruins and desire " an Interactive Kinetic Sculpture by Pamela Jennings Thesis Presentation public slide/talk: Thursday May 9, 1996 6:30 SVA MFA Computer Arts Thesis Show: May 31 - June 15 1996 Visual Arts Gallery 137 Wooster Street, New (...) (31 years ago, 7-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: ni-cads in parallel
|
|
(...) Yes. My problem is that my motors draw somewhere around 2 amps average, and the AA pack I have is rated at 600mAh. This isn't much fun, I'm tempted to leave the thing plugged in instead of charging it every few minutes! It's really not tooo (...) (31 years ago, 7-May-96, to lugnet.robotics.handyboard)
|
| |
 | | ni-cads in parallel
|
|
(...) We've had a debate on this issue a couple of times on the rec.models.rc.air newsgroup a couple times recently (check out www.dejanews.com) and the consensus seemed to be that parallel packs should not be a problem. (...) You should definitely (...) (31 years ago, 7-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Expansion board code
|
|
Can anyone tell me where I can find the code to activate the beta expansion board? Larry ***...*** Larry Randall ***...*** If it works Don't fix it! ***...*** lrand@cts.com ***...*** (31 years ago, 9-May-96, to lugnet.robotics.handyboard)
|
| |
 | | handy board kit research & robot
|
|
i search a handy board kit ??? Where i can find it and how cost it??? Can i found it in Europe or France ??? where can i found information about small robot with handy board herbron@aar.alcatel-alsthom.fr (31 years ago, 9-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: handy board kit research & robot
|
|
Handy Board main web page is: (URL) there are many links to all important information on hardware and software. Handy board is well worth the cost. I love it. An excellent company to buy from here is 'Digital Micro Systems'. I don't beleve there is (...) (31 years ago, 9-May-96, to lugnet.robotics.handyboard)
|
| |
 | | A Project In Planning
|
|
Hi Ya, I am a team member of a team that is planning to build a robotic platform for a research project. What we want to do is build a platform with a Handy Board and a PC on it. The HB will deal with the drive motors (through and interface card to (...) (31 years ago, 10-May-96, to lugnet.robotics.handyboard)
|
| |
 | | infos
|
|
I'm a newbe in this list, not having already built my first HB (but my PCBs are on the way...) and I've some questions: - I think to try to use also ASM on the Handy ... will it be possible? and if so, as i think, where can I get infos on, by (...) (31 years ago, 10-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Summary Re: Ordering from 6270 Technologies
|
|
The 6.270 2.21 board set was gratuitously received on May 8th; although the original email query was sent out 11/28/95 and the check sent out on 12/5/95. The general responses that I received from people responding back is similar to the (...) (31 years ago, 10-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Summary Re: Ordering from 6270 Technologies
|
|
by the way What is 6270 Technologies email address? I've lost my reference to it. cheers ray (31 years ago, 10-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Menu.c converted for HB
|
|
Just to make my tiny contribution to the Handy Board community, I decided to convert the menu.c file for the 6.270 board for use on the Handy Board. It is available in the ic_contrib/jkeyzer directory on cher, for anyone who wants to check it out. (...) (31 years ago, 11-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Continuation of the quest to understand the SPI port
|
|
Hi, Under Interactive C, something is resetting bits 6 and 4 of the SPCR register (0x1028). Whenever we try poke(0x1028,0x5C); and then do a peek(0x1028), we always get back 0x0C!!! Trying to figure out whether this was an instantaneous thing or (...) (31 years ago, 12-May-96, to lugnet.robotics.handyboard)
|
| |
 | | sonar module
|
|
Well, I finally got my Polaroid sonar module in the mail, and I got it working with my Handy Board tonight. My feelings thus far: This thing is pretty neat. However (of course), there are a few quirks that I'm trying to figure out. Distance (...) (31 years ago, 14-May-96, to lugnet.robotics.handyboard)
|
| |
 | | 15' max measurement
|
|
Yup, it looks like 15' is about as far as I can measure. In fact, if the distance is _too_ great, I start getting weird measurements, on the order of 8 or 9 feet. Strange. I turned the gain up a bit, which keeps those erratic measurements from (...) (31 years ago, 14-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: 15' max measurement
|
|
(...) I believe it would matter what type of material you reflect the pulse off of, I would guess. Different surfaces have differenc acoustical properties. Just like they have those silent rooms and echo chambers, etc. (31 years ago, 14-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: 15' max measurement
|
|
(...) I beleive "hard" rigid materials have high reflectivity of sound, such as metal and granite, etc. Pourous materials absorb sound, like brick and wood. You may have notised that sound absorbtions usually involve foam pads on the walls and (...) (31 years ago, 14-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Error Messages
|
|
Hi to all, Why do I get the following error messages when I load my files to the Handy-board? Thank you in advance. Armen Initializing interrupts Downloading 1840 bytes (addresses 8000-872F): 1840 loaded Downloading 78 bytes (addresses 8730-877D): (...) (31 years ago, 14-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Where can i buy L293D in Scandinavia
|
|
I have the problem to locate a suplayer of the L293D needed for the motor output circuit. Can anyone tell me who i manufacturing the L293D. is there any alternate suplyer and which manufacturer is that. Jakob Lundberg mail: jakob.lundberg@atc.mil.se (...) (31 years ago, 15-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Downloading without AC adapter
|
|
Is it possible to download pcode and programs to the HB with having the AC adapter plugged in? -John (31 years ago, 15-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Should I?
|
|
Hi all, I am a young Dutch engineer assigned to build a prototype of a six-legged robot. I am considering to use the handy-board as the controller. There are however a few questions I have. First of all, is it possible to control six motors with the (...) (31 years ago, 15-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Error Messages
|
|
(...) What version of IC are you running? Are you by chance running the old DOS version 2.86x under Windows? -- Randy (31 years ago, 15-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Downloading without AC adapter
|
|
(...) Yes. The interface will draw power from the HB's battery. Don't leave the HB plugged into the interface w/o the adapter for extended periods, because the interface will drain the HB's battery even if the HB is switched off. -Fred (31 years ago, 15-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Thanks for all the replys on the L293D
|
|
Thank you Best regards Jakob Lunderg (31 years ago, 15-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Available J sockets on Hboard?
|
|
Are there any unused sockets on the Handyboard? For example, the bottom 2 sockets in J6 look to be unused, and I could use a couple of sockets to bring out some signals. Now that the thing is assembled, it's difficult to follow traces on the top (...) (31 years ago, 15-May-96, to lugnet.robotics.handyboard)
|
| |
 | | SPI Bus problem solved!!!!!!
|
|
Hi-dee ho, I'm happy to report that I've successfully gotten a Handyboard to communicate to a Miniboard via the Synchronous Serial bus (SPI). The secret was (as I alluded to in my last post on the subject) setting the DDRD (Data direction for port (...) (31 years ago, 16-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: voltage regulator current rating
|
|
(...) Is there any current going directly into GND from the LM2931Z-5.0? If so, would this cause any "extra" heat other than from the current the HB draws? -Eric (31 years ago, 16-May-96, to lugnet.robotics.handyboard)
|
| |
 | | encoders w/sonar?
|
|
After I slap a Polaroid sonar module onto my robot, I'd like to add some shaft encoders. However, it appears that the shaft encoder routines and the sonar routines both use some of the same ports on the digital headers. Is it possible to use other (...) (30 years ago, 17-May-96, to lugnet.robotics.handyboard)
|
| |
 | | IC for Win 95
|
|
Has anyone heard of a release date for a new version of IC for Win 95? The bugs in the present beta are getting... irritating. Maybe I should write a $100 check to Newton Labs and see what happens, eh? :-) (30 years ago, 17-May-96, to lugnet.robotics.handyboard)
|
| |
 | | IC download errors
|
|
Today, IC 3.1 has decided it no longer wants to communicate with my handy board. It detects the board, I select the Handy Board .icd file, and then it tries to download the default files to the board. However, it errors out on each retry, and gets (...) (30 years ago, 18-May-96, to lugnet.robotics.handyboard)
|
| |
 | | IC problems, part II
|
|
Also, IC ctually _works_ if I'm downloading something with my internal modem. This is probably slowing down the transfers IC is making enough for them to work. Once the download stops, however, IC quits working again. Truly strange. (30 years ago, 18-May-96, to lugnet.robotics.handyboard)
|
| |
 | | IC problems, part III!
|
|
Alright, one more fun fact - the old shareware version of IC works fine, running under the Win 95 MS-DOS prompt. I think that eliminates any possibility of a hardware problem, meaning it's IC 3.1 at fault! Hbdl works fine as well, under Win 95. (...) (30 years ago, 18-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: IC problems, part II
|
|
(...) (30 years ago, 18-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Digital Outs?
|
|
How can I set up digital outputs from the handyboard? I would like to drive 3 or 4 LEDs on my robot. Can I make the digital ins outputs? Alternatively, are there any serial rs-232 facilities available on the handy board other than one used for (...) (30 years ago, 18-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Digital Outs?
|
|
(...) See the FAQ: (URL) Alternatively, are there any serial rs-232 facilities available on the (...) This would be easy to do; someone just has to write 6811 machine code to perform async serial out functions. you would be able to use any of the 4 (...) (30 years ago, 19-May-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Greetings! I am new to the handyboard, and am currently building my first robot. I am having a problem with docs.. I have icmanual.ps AND icmain.pdf.. The problem is that I am using an Amiga, and cannot read or decode either of these formats. Could (...) (30 years ago, 20-May-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
(...) OK, take a look at (URL) installed a link for you. Also, did you know the IC manual is on the web? It is at (URL) I am not sure, but I would bet there is an implementation of GhostScript for Amiga. Check it out. This would let you view (...) (30 years ago, 20-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: your mail
|
|
(...) Ghostscript for the Amiga is pretty unusable. I tried it quite a while ago, and got thoroughly sick of it. My solution was to start using my parents' Pentium. :-) (30 years ago, 20-May-96, to lugnet.robotics.handyboard)
|
| |
 | | european handy board users census
|
|
european handy board users, please send me an e-mail, i would like to ask you a few questions. ******** thanks in advance silvain pinot (living in france and wondering if yes or no he will build a handy board) (30 years ago, 21-May-96, to lugnet.robotics.handyboard)
|
| |
 | | So close, yet so far
|
|
AAaarghh. I soldered in the final connections for the outgoing pulse-trains from TOC2. I use the Handyboard to take in pulse trains on IC2 and IC3, massage the numbers, and output the massaged commands on OC2 and OC3. Only the signals go through the (...) (30 years ago, 21-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: So close, yet so far
|
|
This is almost certainly software. your i23o123.icb file is trashing the interrupt vectors and the board crashes. -f (...) (30 years ago, 21-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: So close, yet so far
|
|
(...) But the hearbeat continues on the handyboard, and the software worked before I soldered the Futaba J connector on, hence my thinking that I hurt the board and caused a hardware failure. Could a hardware failure make the board crash at this (...) (30 years ago, 21-May-96, to lugnet.robotics.handyboard)
|
| |
 | | 6 servos
|
|
Hi all, I want to build a six legged walking robot using the handyboard. I want to use 6 servo motors for that. I heard that the handyboard can only control 2 servos, but that there is a servo controller board which can control up to 32 servos, (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: 6 servos
|
|
This multiple servos thing is reaching FAQ status, and here is how I plan to deal with it. Scott Edwards Electronics sells a cheap ($30 kit, $45 assembled) servo board that drives 8 servos. You can gang them to get 32 servos or even more. The boards (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | FW: 6 servos
|
|
This would be a very powerful enhancement to the handy-board. It would obviously allow easy communication between the HC11 and PIC boards. Since my application will use 2+ PICs in addition to the Handyboard, it would allow easy networking of all 3 (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Expansion interface status
|
|
Does anyone know the current status of the expansion interface? My poor handy is at capacity for some i/o functions ;-( (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Expansion interface status
|
|
(...) Yes. The current status is "on hold" while I rethink the feature set. I'm considering doing something more like Scott Edward's little servo board for HB expansion: that is, a collection of small, physically detached boards. For servo's, I (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: 6 servos
|
|
(...) Are the digital outputs at 5v high? I think you mentioned on the HB homepage about the serial interface converting RS232 levels at +12 and -12v to TTL levels (5v). I'm not that familiar with the nitty gritty of RS232 so this kinda puzzles me. (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: 6 servos
|
|
(...) There are two types of serial voltages: TTL level and RS-232 level. The HB's serial interface board converts from TTL to RS-232 for communicating with the host computer. The Scott Edwards board accepts TTL levels, so an HB pin can drive it (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | FW: 6 servos
|
|
RS232 is +12 and -12, but most serial ports can work correctly even if the signal is 3 to 5v. I regularly use 3 to 5v level serial signals. If you need to convert low voltage serial to RS232 specs, you can use a chip like Maxim's 232 - see (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | RE: Expansion interface status
|
|
While I welcome the small kits, they introduce interface issues for beginners, especially if there are multiple kits attached simultaneously - seems like this is a problem the expansion board should be solving rather than causing. The value I am (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Expansion interface status
|
|
(...) Build a 68360 in the expander board, that'll get ethernet, and multiple SCI ports. All the IO anyone should ever need. :-). (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: 6 servos
|
|
(...) Just to make sure it wasn't a typo...so, the TTL level is "ative low"? Also. Does the Scott Edwards board have the ability to be connected to a computer? or do you need a "TTL to RS232 converter"? (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | RE: 6 servos
|
|
You can hook it directly to a PC serial port. Here is the note on it: 1.Controls eight hobby (R/C) servos. 2.Opto input takes RS-232, -422,-485, CMOS and TTL. 3.Baud rate configurable for 2400 or 9600. 4.Addressable up to 32 controllers on one port. (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: 6 servos and RS232...
|
|
(...) From memory of my designer engineer days, the EIA RS232 specification quotes something along the lines of: logical level RS-232 level zero or idle -3V to +15V one +3V to -15V The spec gave maximum slew rates for signals and such specifics such (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Expansion interface status
|
|
Do you think Scott Edward would consider selling just the processor? The expansion board could be made to accept Scott's processor or an unprogrammed one if someone had a different application. Which processor does he use anyway? The other thing (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Expansion interface status
|
|
(...) To Fred and others, I've been thinking about this off and on for over a year now, and since I now have parts I'll finally get my HBs into something more than just board status. Robots eat I/O pins for lunch. Sensors eat input pins and (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | PC serial connection
|
|
Hi. I just got my hands on a new HB and I'm using a 100 MHZ DX PC. Hardware-wise, there's a perfect slot for the serial connection on my computer, which is not occupied. I hookes the serial connection to it and tried to download IC using COM port 4 (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Expansion interface status
|
|
Another thought, how about a series of expander boards. I know this could get really ugly, but, maybe Fred, and the normal HB distributors build what they see are appropriate for their customers, and others build what is appropriate for their (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Expansion interface status
|
|
(...) You might want to note that the unexpanded HB is capable of driving a Polaroid sensor. The second motor chip is removed, and lines are plugged into different pins for the BINH and INIT signals, while the ECHO signal goes to the first digital (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: PC serial connection
|
|
(...) COM 2 is used by the modem card. I don't even know tyhough how to make COM 2 point to the slot I want, which is my initial problem anyways ( I need a 25-pin slot for the serial connection). Sincerely, Yoni Garbourg << To succeed, Atificial (...) (30 years ago, 22-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Wish list, or expansion possibilities...
|
|
Hi, I am new to the handyboard area, having spent most of my project time with 68705 series uP's and 80X51's (done hate me.). Just tossing out some possibilities and not trying to down-play any other ideas that have preceeded me.... An expansion (...) (30 years ago, 23-May-96, to lugnet.robotics.handyboard)
|
| |
 | | expansion board
|
|
Hi all, I have not worked with the handy baord much yet but I also feel that it would be nice to have a few more digital i/o ports available. I guess that is short, sweet, and to the point. sherman@plains (30 years ago, 23-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Fuse on motor power cables
|
|
My current robot platform is a hacked toy and does not have ideal motors. I am concerned about toasting my motor driver chips. Can I put a polyswitch fuse in series in the motor lines to protect against this? They don't seem to be polarity (...) (30 years ago, 24-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Fuse on motor power cables
|
|
(...) All system power, incl. motor pwr, already runs through the existing polyswitch. They're not too fast, so I'm not sure if they'll save you. the motor chips do have over-current protection of their own, though it has been known to fail from (...) (30 years ago, 24-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: pcode, libraries for two servos
|
|
(...) Randy, I'm having trouble making the TOC2 work with Pcode_hb, something trashes the output whether I disable IR-Xmit or not. Do I need a new Pcode in order to divert TOC2 to my own use? I'm treating OC2 the same as I treat OC3, but only OC3 (...) (30 years ago, 25-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Polaroid 6500
|
|
Hi, I am trying to install the polaroid 6500. I use the schematics I found with the sonar.c file at this site. It doesn't work, I dont understand the Motor power connection why does it have 4 pins ? One motor only uses 3 pins ? I think the sonar (...) (30 years ago, 26-May-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Greetings! I am currently porting ic version 2.860 to the Amiga. I have completed as11, dlm, and written a pre-processor in ANSI C for use with this. The problem I m now having is with ic (main) There are many files #included that did not come in (...) (30 years ago, 28-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Interfacing PICs and Basic Stamps to Handy
|
|
Since (I think) it is fairly easy to interface the HC11's SPI interface to a PIC/Basic Stamp I & II this is probably easier than creating a custom RS-232 interface. Has anyone done anything like this? Sean R. Cunningham (30 years ago, 28-May-96, to lugnet.robotics.handyboard)
|
| |
 | | missing source files
|
|
Lyle, Make sure you get the pcode-2.81 tar file in the interactive-c directory on cherupakha. -Fred (...) (30 years ago, 28-May-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: 15' max measurement
|
|
(...) I just noticed that the Polaroid Specs say that the transducer pulse current is 2 A. 100mA idle. Since it was mentioned previously that the HB's VR is rated for 1 Amp, how would this affect the sonar? Perhaps whatever is left of the 1A (...) (30 years ago, 28-May-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
(30 years ago, 30-May-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Greetings! I have just built my first Handy-Board.. Works Great!! I can't decide if I will enjoy writing software or building expansions more, I guess I'll just have to do lots of both before I decide. Two questions. My 'bot has it's own 12 volt (...) (30 years ago, 1-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | cherupakha is down
|
|
FTPs to cherupakha are temporarily out. I'm working on it. -F (30 years ago, 1-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
(...) Yes, see the FAQ for a recently added section on the battery charging system. (...) Yes, this is a good idea if you are separately charging the HB's battery. As you correctly surmise, you don't want the two charging circuits contending with (...) (30 years ago, 1-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Relationship between voltage and analog()
|
|
Hello! Would anybody please send me a mail letting me to know the relationship between the output of ananlog() function and the voltage ? For example, if my sensor works under the command "if (analog(0)>47) then ...." What would be the voltage ? Any (...) (30 years ago, 1-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Relationship between voltage and analog()
|
|
(...) The input voltage range is 0 to 5 v, and the output number range is 0 to 255. The relationship is linear, so 2.5v = 128 (for example) (...) to convert from the output # to the voltage, it would be 5v x (output # / 255) so 47 is about 0.92 (...) (30 years ago, 1-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Greetings! (...) Stupid Question.. Where is this faq? Web or FTP? I also couldn't find the file pcode_2.81.tar you mentioned last week. I will be porting IC 3.1, but wouldn't mind doing 2.81 while waiting for the 3.1 source. (...) Yes, The HB nicad (...) (30 years ago, 1-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | cherupakha is up!
|
|
-Fred (30 years ago, 1-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
(...) The FAQ is linked from the main HB web page under the title "the Handy Board FAQ", or directly at: (URL) pcode source is at ftp://cher.media.mit...dist.tar.Z and also (URL) should fix that last link, because you'd never find it unless you knew (...) (30 years ago, 1-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Fred, I have FTP'ed pcode-2.81.dist.tar.Z from cher (thanks for getting it back!) within it were the files foo.s19, pcode_rw.s19, lobo.asm, pcode.asm, and some makefiles.. Cool, but the files required for compiling IC 2.81 that I can't find are (...) (30 years ago, 1-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
(...) There should be more than that in the archive -- here is what I get: 0 Aug 24 1994:50 1994 pcode-2.81-dist 0 Aug 24 1994:41 1994 pcode-2.81-dist/pcode 17563 Sep 29 1993:42 1993 pcode-2.81-dist/pcode/foo.s19 2209 Sep 29 1993:24 1993 (...) (30 years ago, 2-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Help debugging.
|
|
Well, I didn't get far without running into a bug. In the interface/charger serial circuit, I get 17 volts at pin 2 and I get 0 volts on pin 6. The MAX232 chip is oriented to the right, and all the capacitors have their negative stripes on the left (...) (30 years ago, 2-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Help debugging.
|
|
(...) which pin were you using as ground reference? Maybe redo your test using pin 15 of the Maxim as ground. First check the Maxim is getting good power and ground (pin 15 is ground, pin 16 is +5). Then re-check the voltages on pin 2 (should be +9 (...) (30 years ago, 2-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Help debugging.
|
|
Okay - thanks - you were right - I mis-read the ground location and used pin 7 of the MAX232 instead of using pin 7 of J9. The chip is getting 5 volt range, but the negative voltages are in the mid-8 range - is this something to worry about? thanks (...) (30 years ago, 2-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Help debugging.
|
|
(...) No, mid-8's are fine. -F (30 years ago, 2-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | motors
|
|
HI, Can anyone tell me where to get some good motors that are more powerfull than the LEGO 9V motor but can be implemented into the LEGO's? I want to use the LEGO kit with the suspension, front and rear wheel steering and drive, and 4 speed shifting (...) (30 years ago, 3-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Yup, it works.
|
|
Well after much delay, I've finally got my first HandyBoard up and running. (I've got another one in parts, but that is a different story) I can confirm that HBDL.exe does *NOT* work on my 133Mhz Pentium under Windows '95. It does work on my 486/33 (...) (30 years ago, 3-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Yup, it works.
|
|
(...) I really tried hard to make this clear -- can you explain the difficulty you had? (...) Yup, you are right. You are either the first person to notice this, or the first to report it! (...) Quiescent RS-232 levels are -10v, so the minus voltage (...) (30 years ago, 3-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Adapting the LMD18200
|
|
Over the weekend I decided to use the LMD18200 H-Bridge devices for a larger robot I am building. What I did was simply remove the L293 chip and replace it with a 16pin header and some rainbow ribbon cable. Before you decide this is for you, here (...) (30 years ago, 3-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Success, sorta!
|
|
My long-sought goal of bringing in 2 RC signals to the IC3 and IC2 counters, and sending them out via OC3 and OC2 was not achieved. I was never able to get OC2 to work, and I suspect I need new Pcode like what Randy Sargent wrote to use the buzzer (...) (30 years ago, 3-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Yup, it works.
|
|
I didn't have any problems with the LED's - mine came with a short lead and that always went into the square pad. I imagine I missed the C15 and C16 errors (tantalum vs electrolytic) because I bought a kit and just took the parts out of the packages (...) (30 years ago, 4-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Cris, I just built my HB last week, I can offer these comments.. The green power LED should flash while you are loading the board through the serial port. Actually, it's more of a flicker, it's just an indicator of serial activity. As far as the (...) (30 years ago, 4-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: Yup, it works.
|
|
The PWR light isn't really an indicator of power. It's actually hooked up to the 6811's serial transmit line, so it's supposed to flash when the 6811 is talking serial. the BATT light should always blink when the board is first switched on. It also (...) (30 years ago, 4-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | voltage/current monitors
|
|
I'm interested in building a voltage monitor circuit for my robot's 6V battery, and a current monitor circuit for the motors. Is there an easy way to do this, with reasonable accuracy? I'd like to interface both of them to the analog sensors on the (...) (30 years ago, 4-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Re: voltage/current monitors
|
|
(...) Use a voltage divider (two resistors) to map the battery voltage to a 0 - 5v signal for the A/D converter. Depending on how much current your motors draw, you can put a .1 ohm precision resistor in series with the motor and measure the voltage (...) (30 years ago, 4-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | Strange question
|
|
Has anyone here used Electronic Workbench ? I've got a copy but it doesn't have schematics/models for the darlingtons (TIP120, 125, etc) I'm looking for spice models and ideally an symbol library. (yes it is for simulating various power control (...) (30 years ago, 5-Jun-96, to lugnet.robotics.handyboard)
|
| |
 | | encoders??
|
|
Let's see. First, I'd like to put a pair, if possible, of shaft encoders on my robot. (It's annoying not being able to tell how far I've gone!) Anyways, digital inputs 7 and 9 are being used by a 6500 Polaroid sensor and an RC servo. Is it still (...) (30 years ago, 5-Jun-96, to lugnet.robotics.handyboard)
|