To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3601 (+100)
  RE: Multitasking (fwd)
 
Does your while loop have a break(); statement. I have an idea that this may be necessary in some situations. -----Original Message----- From: MAR ERICSON [SMTP:mar@cooper.edu] Sent: Monday, 6 April 1998 8:46 To: Handy Board mailing list Subject: (...) (29 years ago, 11-Apr-98, to lugnet.robotics.handyboard)
 
  Smooth PWM in IC 3.1?
 
I apologize for asking a question I think I've seen answered, but I can't find it in the mail archives. Is it possible to use Julian Skidmore's smooth PWM routines with Newton Labs' commercial IC 3.1? Since they use a different version of pcode.s19 (...) (29 years ago, 11-Apr-98, to lugnet.robotics.handyboard)
 
  Re: SPI?
 
(...) What Hacker said, but also, there's a 2x4 female SPI header on the HB just above the power jack that allows you to hook up other serial devices to the HB (like other HB's, memory, etc.) It's shown in the HB Tech. Reference and there are (...) (29 years ago, 11-Apr-98, to lugnet.robotics.handyboard)
 
  Re: SPI?
 
(...) this is correct... (...) but this is not. the Handy Board communicates with the desktop computer using the SCI: serial communications interface. The SPI is for high speed (up to 1 megabaud) sychronous (i.e., separate clock signal) transfer to (...) (29 years ago, 11-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Smooth PWM in IC 3.1?
 
(...) Yes, it is possible. It must be, 'cause I've been doing it. You simply need to download Julian's pcode_hb.s19 (rename your other one first) and put it in the IC31\libs directory (or whatever you call it). IC 3.1 ought to automatically load it (...) (29 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
 
  Rere: Smooth PWM in IC 3.1?
 
At 08:17 PM 4/11/98 -0600, I wrote: <snip> (...) <snip> Correction: You'll also need Julian's lib_hb.c to go with it. Again, rename your current version first so you don't overwrite it. Put the new one in the libs directory where the old one was, (...) (29 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
 
  16 digital outputs as Fred suggested
 
Hi guys, I needed 16 digital outputs for my handyboard, so I put up a very simple expansion board the way Fred suggested in his handboard FAQ: I connected two more hc374 with their d-inputs to LCD-display's data bus (d0 - d7). Then I connected the (...) (29 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
 
  RE: Multitasking (fwd)
 
I duno... I fergot. Sorry. :( It was a long time ago (milage-wise). I didn't use that method of mutitaking anymore and I didn't save the old code. But, I don't think so, I can't imagine that would be my style. I would set a global variable from (...) (29 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
 
  >1A adapter?
 
Hello folks, I am currently using the HB to control a robot tethered to a PC (via the serial/charger board), as I'm using genetic algorithms to evolve controllers. The robot pulls about an amp (with motors, servo, sonar etc.), and I'm running it off (...) (29 years ago, 12-Apr-98, to lugnet.robotics.handyboard)
 
  Analog Encoders
 
Hi, when I compile fencdr0.asm, I get "xxxjunk.c"(68): Warning --- Value Truncated "xxxjunk.c"(70): Warning --- Value Truncated "xxxjunk.c"(68): Warning --- Value Truncated "xxxjunk.c"(70): Warning --- Value Truncated Does everyone else get this (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Vector V2x Compass
 
Hello: I have a V2x compass and I was trying to hook it into my handyboard using Tom Brusehaver's .icb, .c and instructions as described in the contributed section. I have also grounded the M/S pin on the compass. The EOC pin is sent to the HB thru (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help - Cannot download!
 
try using DL.EXE (part of the Interactive C distribution) after following the serial port options directions given the FAQ (under downloading problems). fred In your message you said: (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Re: 16 digital outputs as Fred suggested
 
1. please read the Appendix B documentation in (URL) explains this in more detail than the FAQ. 2. you must the even-numbered Yx signals for output latches. Since Y6 is taken (by the on-board latch for the motor drivers), you're left with Y0, Y2, (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Vector V2x Compass
 
Hi Armeen, I have the same problem as you. I thought my HB was faulty or it doesn't work with the 68hc11E processor I use or something. So what I did was: I wrote a very simple IC-Routine. You have to load this program with "load v2x.c" and call the (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Servo Routines
 
Question. I've been playin with the servo routines available from the HB page. One thing I've noticed. The servo's seem to chatter a lot. Is this normal. A routine that does nothing but loop, read the knob and output a value based on the knob to the (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  re-download problem
 
I forgot to unload the program that I was running on my handyboard before I quit out of ic. and it won't let me putting the board on bootstrap mode. as soon as I power up the board, it starts running the last program. can anyone tell me how to clear (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Servo Routines
 
can you ascertain whether the knob is returning the same value every time through the loop? i wasn't clear if "even when the knob is not changing" meant just that you weren't turning the knob, or whether you were sure it was always producing the (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Servo Routines
 
When I see the servo chatter, the knob is returning the same value. In fact I can just set a constant unchanging value without using the knob and get the chatter. I've tried this on two HB's and get the same results. The servos are small Futabas. (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Re: re-download problem
 
Hold down the START button while powering on. This will prevent the board from running main(). Fred In your message you said: (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Re: re-download problem
 
Try turning off the board and holding down the start button while re-powering the board. Hope it works for you. Terry P. Gathright ---...--- (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Are the codes proprietary
 
Hi: I was wonderig if the codes such as analog(), digital(), process() etc are proprietary. If not how can I see the C/assembly version of them. I need them to learn how Motorola 68hc11 assembly works and also I am a bit curious. Any help would be (...) (29 years ago, 13-Apr-98, to lugnet.robotics.handyboard)
 
  Are these codes proprietary
 
Hi: I was wonderig if the codes such as analog(), digital(), process() etc are proprietary. If not how can I see the C/assembly version of them. I need them to learn how Motorola 68hc11 assembly works and also I am a bit curious. Any help would be (...) (29 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
 
  Are these codes proprietary
 
Hi: I was wonderig if the codes such as analog(), digital(), process() etc are proprietary. If not how can I see the C/assembly version of them. I need them to learn how Motorola 68hc11 assembly works and also I am a bit curious. Any help would be (...) (29 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
 
  Re: analog encoders
 
(...) Mar, I ran into these warnings when I was modifying sencdr0.asm. They do in fact show a bug in the assembly code, but it's harmless. If you like gory details, here they are: Near the beginning, the file defines these constants: BASE EQU $1000 (...) (29 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
 
  AS11_IC
 
Hi to all ! Help, where can I get the AS11_IC for PCs (to produce *.icb files) ? Thanks for all response. (29 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
 
  Big adapters?
 
Hello all, I'll just briefly restate my earlier questions for ease of responding: 1. Why are we encouraged not to use big adapters (>1A) for the HB? Is it because of the charging circuit, or does it fry the board? 2. Can I plug a big adapter into (...) (29 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Servo Routines
 
I have noticed in my experiments that the HB servo routines don't interact well with the LCD. In order to get them to work reliably in my Handyboard library I redesigned the way the LCD driver worked. Unfortunately for you that library was built for (...) (29 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Servo Routines
 
Hi all, Futaba servo's chatter when the pulses are not updated quickly enough. At best, this produces a slight buzz, at worst they 'hunt and seek' their position a tiny bit. I don't know how fast the HB routines update the pulse, but standard (...) (29 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Big adapters?
 
In your message you said: (...) because if you put it into zap mode, you'll fry your batteries -- unless you've switched to a much higher amperage pack. (...) no, because you can't send that much current down the RJ11 cable. unless your robot draws (...) (29 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
 
  Re: AS11_IC
 
it's there in the software section: (URL) your message you said: (...) (29 years ago, 14-Apr-98, to lugnet.robotics.handyboard)
 
  downloading
 
Hey. I just got a couple more handyboards and both of them had exactly no power in them. Ive let one charge for about 12 hours and then tried to use the Initialization app on it and it wont synchronize with the board. Does anybody know what im doing (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  ack
 
Nevermind my last message. I had a phone cable that was dodge. Out of curiousity...Is anyone on this list familiar enough with C to make a program that you could input wheel diameter and wheel base along with the weight of the robot and reference (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  Handyboard simulator
 
Hey, I was wondering whether anyone knew of a Handyboard simulator. I am working on a group project where each person develops code in C using IC for the Handyboard. The problem is that we have only one handyboard and thus only one person is able to (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  Problems connecting 2 Handy Boards
 
Hello everybody, We tried to link two Handy Board, via the RJ11 computer connectors, in order to make them communicate with the code we found at (URL) . But, when we plugged the cable, the Handy Boards began to smoke next to these connectors. Does (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  RE: Problems connecting 2 Handy Boards
 
-----Original Message----- De: Ecole Louis de Broglie - Promotion 1999 <promo99@ecole-debroglie.fr> Para: handyboard@media.mit.edu <handyboard@media.mit.edu> Fecha: Miércoles 15 de Abril de 1998 06:27 Asunto: Problems connecting 2 Handy Boards (...) (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  How work the downloader?
 
I'm still problems with two boards. I'm still can download code , but never "boot". That code work in all others board.I can't make run off course, IC. My answer is : The downloader check every byte it download to the board from the memory??? Or (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Problems connecting 2 Handy Boards
 
The code found at (URL) was intended for connecting a Handy Board to the host PC. It is possible to connect two Handy Boards, but you must use a NETWORK style RJ11 cable, rather than the usual TELEPHONE style RJ11. See the FAQ, under entry "The R11 (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  64K RAM?
 
Hello, I wonder if anyone knows if I can expand the Handyboard's memory to the maximum of 64KB simply be wiring in a 128kb SRAM (A16 unused so it becomes 64kb) with D0-D7 to the data bus as usual and A0-A14 to the existing RAM socket and A15 from (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  Re: 64K RAM?
 
This is a common question, so I went ahead and put an answer in the FAQ. Take a look at: (URL) what it now says: ---...--- IS IT POSSIBLE TO EXPAND THE HANDY BOARD'S MEMORY TO 64K? Actually, this is hard to do. Here's why: 1.There is a compromise in (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  Handyboard simulator
 
Hello, I was wondering whether anyone knew of a Handyboard simulator. I am working on a group project where each person develops code in C using IC for the Handyboard. The problem is that we have only one handyboard and thus only one person is able (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  mem command &...
 
1. The freeware version of IC had a command ('mem' if me recollection is correct) that returned the amount of free memory in the HB, but that command doesn't seem to be available in the most recent commercial version. is there some other command (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  Miniboard, ICC11, and printf
 
I have a miniboard and I am using the free version of ICC to program it. I did replace the standard crt.s with the one for the miniboard, but I am unable to get printf to work. Actually, I am unable to download programs that use printf. The sample (...) (29 years ago, 15-Apr-98, to lugnet.robotics.handyboard)
 
  Where to buy Speedwire ?
 
I am looking for a place to buy "Speedwire" as mentioned in Mobile Robots Inspiration to Implementation book. Thank you, -Pandit (29 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
 
  HandyBoard Buffalo V1.0
 
Hello All, Some time back I sent a message to the HandyBoard list to enquire if anyone had a machine code programming monitor operating system for the HandyBoard, similar to the Buffalo Monitor on Motorolla's EVB boards. (The Buffalo system allows (...) (29 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
 
  HandyBoard Buffalo V1.0 - Update
 
Hello again, Fred G. Martin had informed me that I forgot the assembly code for the Buffalo monitor. It is now on the page, (URL) BUF_HB.TXT Charles Hacker School of Engineering Griffith University - Gold Coast PMB 50 Gold Coast Mail Centre (...) (29 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
 
  Using Port D of the Handy Board
 
Hello everybody, A few month ago, someone told us that we can use port D as an ouput. But, we've just read on the Handy Board FAQ that it was not possible. So, where is the truth ??? Help, help, help !!!!!!! We need 8 ouputs (and also 8 inputs) to (...) (29 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Using Port D of the Handy Board
 
In your message you said: (...) ve just read on the Handy Board FAQ that it was not possible. So, where is the truth ??? where in the FAQ does it say that it's NOT possible? If you look at the link (URL) explains how to use Port D as outputs. (...) (...) (29 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
 
  Writing in port D of the Handy Board
 
Hello, We've just read the Web page "Additional Digital Inputs & Outputs for the Handy or Finger Board" at (URL) we don't know how to write in the port D (ie D0..7 ) in order to have more digital outputs. Please could you tell us how to do ??? (...) (29 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
 
  polaroid sonar problems
 
We continue to progress on our first robot here at Northwestern but have run into a problem with our sonars. We have run out of solutions to try and would appreciate any help from people experienced with the polaroid sonar modules. Our sonar is (...) (29 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
 
  ds1233
 
Help: I am short one ds1233 for my freshman engineering class. Is there anyway to jumper around this part. I understand that it is in the circuit to prevent the cpu from losing it's mind on low voltage. I would be willing to put up with reloading (...) (29 years ago, 16-Apr-98, to lugnet.robotics.handyboard)
 
  Re: polaroid sonar problems
 
Hi all if anyone has problems using the 6500 series for distances below 35cm by using the binh signal I have a possible solution to the problem. We also expierienced problems using the sensors for distances between 15cm and 40cm. We finally found (...) (29 years ago, 17-Apr-98, to lugnet.robotics.handyboard)
 
  questions on optical encoders
 
Hi, everyone Hi, i am currently doing a thesis topic "Micromouse project". And, I am going to purchase an small optical encoder to measure the speed, acceleration and distance that my mice has taken. My mice is driven by a DC motor, so the opti. (...) (29 years ago, 18-Apr-98, to lugnet.robotics.handyboard)
 
  Re: questions on optical encoders
 
On Sat, 18 Apr 1998, Paul wrote: Might I suggest taking a look at US Digital's optical encoders? (URL) have some low cost variants that we used and were very pleased with. I am looking at the data sheet for a "SP-16" <snip> (...) It is 1.78" in (...) (29 years ago, 18-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Optical Encoders(thanks)
 
Thanks Daniel & David for your help. (29 years ago, 19-Apr-98, to lugnet.robotics.handyboard)
 
  FW: Optical Encoders
 
I sent to this to Paul personally . . . there may be general interest. (...) (29 years ago, 20-Apr-98, to lugnet.robotics.handyboard)
 
  encoders
 
I haven't had a chance to experiment with this yet, but it look like a something that might work. Have you check out any mice, some of them have two encoders on them. they are small, low power and cheap. I plan to experiment with them this summer, (...) (29 years ago, 20-Apr-98, to lugnet.robotics.handyboard)
 
  Help encoders with quadrature outputs
 
Hello, I am curently trying to use encoders with quadratures outputs If someone has already developped a program for such encoders I would be very interested in. A 8 bits counters can also be connected to this encoders. If someone has already (...) (29 years ago, 20-Apr-98, to lugnet.robotics.handyboard)
 
  loading files with IC
 
Howdy from the world of program failure... please consider this scenario: 1. let's say I write a series of functions, put them in a file, and download the file to my HB. Now I write a program that uses the previously downloaded functions, and (...) (29 years ago, 20-Apr-98, to lugnet.robotics.handyboard)
 
  newby
 
Hi. I teach 8th grade science and I am very interested in adding Robotics to our curriculum in the fall. I have been following with keen interest, the listserv on the handyboard. Could somebody tell me, where I can obtain reading materials to help (...) (29 years ago, 20-Apr-98, to lugnet.robotics.handyboard)
 
  Class functions from C++ to C
 
I'm using A-Life techniques to control a simple robot. The program I'm using was initially written by my A-Life professor in C++, and as I use IC, I need to bring it over to C. I'm having difficulties as it calls a class (bots) from a C++ library (...) (29 years ago, 20-Apr-98, to lugnet.robotics.handyboard)
 
  Serial Communication: HB -> Win95
 
I am using the serial_putchar() and serial_getchar() communication routines on the HandyBoard, and everything is working fine from the PC to the HB. However, I am having trouble getting the HB to send data back to the PC. Here is main() on the HB: (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Class functions from C++ to C
 
Hi Kate you could use some precompiler to convert C++ to C. I think that the GNU C++ compilers have such a precompiler. (At least the older ones do.) Tom krasing@iastate.edu schrieb: (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Help!!! Polaroid problem!
 
I am trying to use one of the Polaroid 6500 kits from Wirz with my senior design project. It doesn't exactly use a handyboard, but our microcontroller is virtually identical at the lowest level. The problem is when we attach the device to the scope, (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  is IC compatible with the MC68HC11F1
 
hi from France, I already have a handy-board running with a 11A1 chip and I plan to adapt the circuit for a 11F1 chip, with the same memory map. Does someone have any experience about running IC with this chip? Will it work with the pcode_hb.s19 (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Help!! Polaroid problem!!!
 
I am trying to use one of the Polaroid 6500 kits from Wirz with my senior design project. It doesn't exactly use a handyboard, but our microcontroller is virtually identical at the lowest level. The problem is when we attach the device to the scope, (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Are you using a pullup resistor on the ECHO pin? If not that is your problem. The ECHO output is an open collector driver which requires an 4.7 K pull-up resistor between the output and Vcc. The pull-up is necessary for connecting the module to a (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Handy board help
 
I am interested in using the Handy Board, but I have a few questions about it first. Please help. :) I noticed the Handy Board supports 4 motors but I am interested in using stepper motors with it. Is this possible? If so what modifications would be (...) (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  tsl1301 or 1401
 
Has anyone tried to use one of the TI tsl1301 or 1401 linear sensors with the HB. I ended up with a few but am having a tough time trying to figure out what the data sheets are trying to tell me. Not real clear (to me). Bruce A. Moore (29 years ago, 21-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Why does it seem like everyone except me needs a pullup resistor and perhaps a capacitor somewhere to operate the Polaroid? I've never had any problems without any of these components. ??? The first time I connected the sensor, it worked perfectly. (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  To Prof. Fred Martin: Neat!
 
Hi, I saw your robot at the Trinity fire fighting contest last Sunday. It was neat, and very animate. I was curious to know if you had figured out why it did what it did during your first run (?). And, what type of sensor were you using on the rear (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  IR Transmit ?!? HELP
 
I recently assembled a Handy Board, everything is perfect except for the IR Transmitter. The IR Tx LED does not light. It is not the LED itself because I replaced it. I can't seem to figre out what's wrong. Please help. Thank You Peter Eacmen (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: IR Transmit ?!? HELP
 
(...) Did you follow the instructions in the HB Assembly debug? at (URL) says: Output Stage If LED9R fails to light after the poke command is issued, trace the following progression of signals. Please refer to the infrared output schematic: * 6811 (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  PWM and encoder
 
Hi, i have some questions about PWM and encoder. I made following tests: 1) Speed : motor(0,100) my encoder count f.e. 20clicks / per second 2) Speed: motor(0,50) my encoder count f.e. 15clicks / per second 3) Speed: motor(0,40) my encoder count (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Digitial input problem
 
Hi all, i have built a handyboard. It works fine. But on Digital PIN 9 "PAI" i got allways high level (1) during test via "hptest.c". I think i haven´t any soldering problems. That´s wrong ??? bernd klein (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
well....I might be the way you are powering the sensors ??? Maybe luck ???? :)))))) Actually I don't why you don't need any of those supporting parts. A short question ...For what range are you using the sensors (are you using the binh signal) ?? We (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  IC stack problem
 
Hello everybody, Is something wrong with this code or is it IC? { int a[4][4], i; for (i=0; i<4; i++) { a[i][i]=i; } } When I type this at the IC prompt it complains: Downloading 79 bytes (addresses C200-C24E): 79 loaded COMPILER ERROR!: 2 extra (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
The reason you don't need a pull up resistor for the Handy Board is because the Handy Board has built in 47k pull up resistors on the digital inputs! -----Original Message----- From: MAR ERICSON <mar@cooper.edu> To: Darkman <lroska@cyberus.ca> Cc: (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: PWM and encoder
 
The nonlinearity has to due with the characteristics of your motor. You will find that a single step of power at the low end has a greater effect on the speed than a single step at the high end, as the motor approaches its top speed. The (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Handy board help
 
You can build a stepper motor controller on a separate circuit board, then remove the motor control IC's off the handy board and use the output signals to control your stepper. Will have to write a program to run it. you will need a min of 4 outputs (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: loading files with IC
 
In fact, that's weird.. I can't answer to that. To me, I'm pretty sure that IC would have gave me an error, like when I try to load a C program without having loaded the ICB containing the special function used by this C program. For example, i (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: IC stack problem
 
(...) The funny thing is, it doesn't complain about arrays smaller than 4x4. All values are stored correctly for an array of size 3x3. What's this 'magic' number 4 then? Jan Sipke van der veen (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Serial Communication: HB -> Win95
 
To answer my own question, at least partially, here is a Win95 Host program to communicate (single bytes) with the HandyBoard over a serial line: /* Win95 Visual C++ Host Code to talk to HandyBoard */ #include <conio.h> // _outp, _inp #include (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
When it first worked for me, I used the HB NiCd. I grounded binh and it worked. I used binh to measure like 7 inches and it worked fine too. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: PWM and encoder
 
The 100, 50, 40, etc. are not really "speeds". They are power. It is related to the average voltage level of your output. Speed depends on the torque and characteristics of your motor. You can hold on the the wheel and still drive the motor at 100. (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: PWM and encoder
 
Well, actually, it's not power either. Power is V * I. Sorry, it's actually the voltage. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
oh yeah? Well, what about the capcitor, huh? ;) ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of Science and Art (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  A few questions....
 
First I want everyone to know two things. First I am new to this list. Second, I have moderate knowledge of electronics.... Until about a few weeks ago, I had been working with Basic Stamps 1 and 2. After looking at all the information about (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Trinity College contest report
 
Hi all, first, the URL: (URL) went to last weekend's Fire-Fighting Robot Contest at Trinity College, along with my colleague Steve Ocko, who had built a cute robot based on our network-cricket technology (see (URL) for more on that). We spent about (...) (29 years ago, 22-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
(...) residual noise? It was my understanding that the Polaroid module used pulse time differentials to relay distance information. One need only look at the difference in time, between the leading edge of the init pulse, and the leading edge of the (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Re: PWM and encoder
 
(...) Are you using the "smooth" PWM motor routines? Note also, that a DC motor does not change velocity linearly with an increase in current unless it is under load. This was a recently asked question on the list. Maybe grepping the digest for (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Generally the capacitor is the problem :-) The capacitor in the original note is there to pull BINH true* to allow the sensor to detect things that are closer than 18". Generally, when you include it, unless the design of the system holding the (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  examples
 
I was wondering if anyone out there could send me some very basic, easy to understand programs that could help me figure out how to use sonar modules. Thanks, Richard (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Hey, I just wanted to thank everybody for there help with this, it did turn out to be the pull up resistor problem, I feel like a moron. We used the handyboardy sonar interfacing schematic when we wired it up and failed to realize that we aren't (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  A Few Questions
 
First I want everyone to know two things. First I am new to this list. Second, I have moderate knowledge of electronics.... Until about a few weeks ago, I had been working with Basic Stamps 1 and 2. After looking at all the information about (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Stepper motor help
 
I am planning on using stepper motors w/ a handy board and will be powering them separately from the rest of the board. What type of motor should I use? I have seen 6 and 12 volt motors availble, if anyone can recommend which to use I would (...) (29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  subscribe
 
(29 years ago, 23-Apr-98, to lugnet.robotics.handyboard)
 
  Re: IC stack problem
 
Dear Jan-Sipke, Two-dimensional arrays are not implemented in the freeware IC 2.8 -- sorry. I just tested and your code works fine with IC 3.1/3.2. -- Randy ---...--- (...) (29 years ago, 24-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Handy board help
 
Hi For a relatively simple solution you may want to look at (URL) have connected and run steppers using this method. It does not get the best from the motors but it will let you experiment easily. (29 years ago, 24-Apr-98, to lugnet.robotics.handyboard)
 
  Smooth PWM routines for IC 3.1/3.2
 
Thanks to Julian Skidmore and Scott Seaton, we have a version of pcode and libraries for IC 3.1/3.2 which implement Julian's "smooth pwm" routines for the MIT Handyboard. To grab these, please go to the following address: (...) (29 years ago, 25-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Handy board help
 
(...) Thanks for this excellent article on driving stepper motors from the Handboard. One little yet very important question: when you say "the common wires need to be connected to the motor positive supply" what exact handyboard pinout are you (...) (29 years ago, 25-Apr-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR