To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 26014 (-100)
  Re: Game Boy + LEGO = Robot
 
(...) Hi Philo, Yes they are, give or take, the same. However, the Charmed Labs ones have Lego axle holes! Danny (URL) (20 years ago, 28-May-06, to lugnet.robotics, FTX)
 
  Re: Game Boy + LEGO = Robot
 
(...) Have also a look to these: (URL) (same wheels?) shawn to me by Bernard Catt. Philo (20 years ago, 28-May-06, to lugnet.robotics)
 
  Re: Problem with RCX
 
(...) I agree - and furthermore, whilst a dead short might well cause a battery leak (when the batteries get hot, the contents can expand and rupture the cell) - it's kinda unusual for a battery leak to cause a dead short - the corrosive gunk inside (...) (20 years ago, 28-May-06, to lugnet.robotics)
 
  Re: Problem with RCX
 
(...) The dead short could have caused the batteries to leak. That's probably the only way to get batteries to leak in only a week. (20 years ago, 28-May-06, to lugnet.robotics)
 
  Re: Game Boy + LEGO = Robot
 
(...) Ahh, between the two articles; yours and the one on Charmed Labs, I learned a lot about this technology. THANK YOU e p.s. yes those Omni Wheels are very cool! (20 years ago, 27-May-06, to lugnet.robotics, FTX)
 
  Re: Game Boy + LEGO = Robot
 
(...) Eric, I came across this some time ago, and even thought about seriously as a controller, although quids in its a bit pricy to buy the device and a GBA if you havent already got one just to use this. I have just dusted off a page I have on it (...) (20 years ago, 27-May-06, to lugnet.robotics, FTX)
 
  Game Boy + LEGO = Robot
 
A friend pointed this out to me. (URL) e (20 years ago, 27-May-06, to lugnet.robotics, FTX)
 
  Problem with RCX
 
I have a 2.0 RCX that is only about 6 months old. I had just put a new set of batteries in it the other day and it was working fine. I had not used it for about a week and then tried it out and it was completely dead. I opened up the battery box and (...) (20 years ago, 26-May-06, to lugnet.robotics)
 
  Re: NXT Line Follower
 
(...) Good question. I never tried it that way... and now the bot is in pieces for my next idea... (20 years ago, 26-May-06, to lugnet.robotics)
 
  RE: NXT Line Follower
 
Just wondering whether the same (unmodified) program will also work when you set the robot to follow in the opposite direction. It appears that you're following the outer edge of the line and I was wondering about the performance when following the (...) (20 years ago, 26-May-06, to lugnet.robotics)
 
  NXT Line Follower
 
All, I have posted pics and video of my NXT Line Follower. (URL) (20 years ago, 26-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
Hello John, (...) I have played with this command, it seems that only the low nibble of paramater is useful. The interval range goes from 12.5ms for 0 to 3s for 0xf. Interval seems to be roughly proportional to the square of the parameter. I have (...) (20 years ago, 24-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) Excellent! Thanks for the update, and it's great to know this is availible within the HW. I wish NXT-G had access, but... well, either it eventually will, or LEGO has specificly included goodies in the FW just for 3rd party environments. (...) (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) I can confirm that the 0x2, 0x41, 0x0 "off" command does, indeed, turn off the clicking sound that you can hear coming from the US sensor. I can also confirm that the 0x2, 0x40, 0xNN "set measurement interval" command does set the measurement (...) (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) ; us_off.nbc ; ---...--- variable declarations ---...--- dseg segment ;------- definitions ------- TCommLSWrite struct Result sbyte Port byte Buffer byte[] ReturnLen byte TCommLSWrite ends ;------- declarations ------- thePort byte 0 // port 1 (...) (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) OK, verification done, the voltage is correctly switched to 5V with the touch sensor. I probably programmed a wrong port# ! But clearly the 5V is enough to power the US transducers (probably with reduced range) Philo (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) OK, and since I'm one of the few... I sent up a stationary NXT with an US sensor, and a "target" NXT with an US sensor as well, pointed directly at each other. Furthermore I had the "target" move back and forth to vary the range slightly. I (...) (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) I'm not sure yet; I admit to not being even remotely a "hardware guy", which is why I keep doing all this SW testing :-). (...) Another odd feature is that the ping frequency seems to change with both what you define the sensor as well as (...) (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) Sorry Brian, you are right! my ageing ear was not able to get the much weaker "ping" at first. My interpretation (to be confimed) is that the US sensor goes on working even if not configured, but some sensor modes don't provide the 9V supply (...) (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) Agreed... perhaps surprisingly, based on dozens of hours of testing, with 1) sumo bots with a ring of sonars on all sides 2) Lego bots with two sonars on the front, we found no discernable problem. This is an anecdotal report, but the (...) (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) Within the same room - is unlikely to be a problem - but think about two Sumo bots trying to find each other or two robots doing some kind of cooperative tasks in a contest or something...not likely to be so easy I think. (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) I'm not positive of that. If the US sensor is plugged in to a powered NXT, I can detect a clicking from it - I presume it's on. Regardless of what sensor I define the port as, this clicking continues. This is what I was basing my "can't turn (...) (20 years ago, 21-May-06, to lugnet.robotics)
 
  External power supply for NXT
 
Hi all, You'll find (URL) here> detailed building instructions for a replacement battery plate that adds an external power jack to the NXT. (URL) Enjoy, Philo (20 years ago, 21-May-06, to lugnet.robotics, FTX)
 
  Re: Ultrasonic sensor interactions
 
Hello Brian, (...) That's easy to do in NBC, and not hard with NXT-G: to shut off the US sensor, just "use" another sensor type on the same port. Here is a sample program that switches the US sensor on/off with NXT enter button. (URL) If the sensor (...) (20 years ago, 21-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
I've heard of one possible answer, though don't know if it is feasible on the NXT. If the robot software sends timed pings, regardless of time of flight, they will be returned with the same delay between them. So if you send two pings 73 msecs (...) (20 years ago, 21-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) I was the one that mentioned that I couldn't find a way from the SW I have to turn the US sensor off. That said, I don't think it's time yet to worry about intractable problems: A hundred of us or so have been playing with this stuff for a (...) (20 years ago, 21-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) Wow! That's a lot lower than I'd have expected - at that frequency there is a good risk of harmonics from normal sound interfering with it. (...) Right - 350 meters per second is pretty slow by computer standards. (...) (Not to mention things (...) (20 years ago, 21-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) The device operates at 40kHz, the transmit and receive piezo devices are only resonant at that frequency. Even though the measurement period is short (time from transmit to time to receive) it is necessary to wait quite a while for the sound (...) (20 years ago, 21-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) The 'Aloha' protocol was the predecessor of this. (...) Someone earlier told us that the thing runs all the time and can't even be shut off. That being the case, I think we're pretty much doomed. (...) Yes - but the relatively low frequency at (...) (20 years ago, 21-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) How about a single computer that was Bluetooth accessable. The server could act as a "lockable" resource that a NXT could acquire prior to doing the US detection. Then the NXTs don't need to know about each other, just the main server (and it (...) (20 years ago, 21-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
The problem here is the management of a single shared resource, i.e. the air through which the ultrasonic signals travel. The lack of a Bluetooth broadcast mechanism makes the implementation of a conventional resource locking system difficult, but (...) (20 years ago, 21-May-06, to lugnet.robotics, FTX)
 
  Re: Ultrasonic sensor interactions
 
(...) This is a great idea except for one very important item: there is no such thing as a broadcast message (ie: a message sent to everyone) using Bluetooth. So for any such system to work, each robot has to know about every other robot, and send (...) (20 years ago, 21-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) The problem with that is that both NXT machines may be listening. Neither hears anything - so both decide to emit a ping - and they still interfere with each other. The nasty part is that even if you can detect that an interference happened, (...) (20 years ago, 20-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) A better alternative would be to develop protocols in which the NXT controllers use their communications to tell each other what they are about to do. If you can sent a message that says "I'm about to do an ultrasound 'ping' - so you'd better (...) (20 years ago, 20-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) Very feasible... IF you could turn the US sensor off. As near as I can determine, the US sensor, when connected, is never off: it is always emitting a series of "pings" (you can actually hear a "click" from the sensor if you are really close). (...) (20 years ago, 20-May-06, to lugnet.robotics)
 
  BrickFest Bulletin: Mindstorms/Technic Contests and Events, Space Contests, Castle Contest and..
 
(URL) Mindstorms/Technic Events BrickFest 2006 is fast approaching! This year, the Technic and Mindstorms Theme coordinators are pleased to announce 5 competitions. The competitions will be spread across the 3 days of BrickFest. The planned (...) (20 years ago, 20-May-06, to lugnet.events.brickfest, lugnet.events, lugnet.robotics, lugnet.robotics.events, lugnet.space, lugnet.castle, lugnet.general, lugnet.announce, lugnet.build.contests, FTX) !! 
 
  Re: Ultrasonic sensor interactions
 
Hi Tim, (...) it should be possible to use the ultrasonic sensor itself for that, there is a command to listen in on other sensors for that purpose. Jürgen (20 years ago, 20-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) How feasible would it be to set up some sort of time-sharing communications over Bluetooth to allocate time slots when each of the robots in an area would be allowed to use their ultrasonic sensors? -Tim (20 years ago, 20-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) In a word, multiple ultrasonic sensors can be a problem. This is a general problem and not specific to Lego ultrasonic sensors. Pulses emitted by "the other sensor" can arrive at just the wrong moment, creating a false range reading. Clever (...) (20 years ago, 19-May-06, to lugnet.robotics)
 
  Re: RCX Virus?
 
(...) But (critically) not ALL of the stuff! (...) What I suggested was that your rechargable batteries are at the end of their lifespan. Buy a set of regular NON-RECHARGEABLE batteries and see if everything works OK then. If it does then toss out (...) (20 years ago, 19-May-06, to lugnet.robotics)
 
  Re: RCX Virus? - battery output and RCX performance
 
(...) I think that NiMH should be up to the task at that power level (difference between NiMH and NiCd occur at much higher discharge rate). But maybe there is one or more dead cell that cant't hold its charge? Since NiMH provide 7.2V instead of 9V, (...) (20 years ago, 19-May-06, to lugnet.robotics)
 
  Re: RCX Virus? - battery output and RCX performance
 
(...) The Lego geared motors can pull about 250 mA when stalled, and close to that when heavily loaded. So for three motors, that may be more current than your batteries can deliver. Rechargeable batteries, esp NiMH, don't deliver the same peak (...) (20 years ago, 19-May-06, to lugnet.robotics)
 
  Ultrasonic sensor interactions
 
Can someone from the MDP comment on how multiple robots using the ultrasonic sensor interact. It is possible to use this sensor reliably when one or more other robots nearby are using theirs? -Tim (20 years ago, 19-May-06, to lugnet.robotics)
 
  Re: RCX Virus?
 
ok, I finally got to trying some of the stuff you recommended. I recharged the batteries and tried downloading the firmware. It can run the whole program without the motors being plugged in. It can even run the program with all motors plugged in but (...) (20 years ago, 19-May-06, to lugnet.robotics)
 
  Re: Thoughts
 
Hi Andrew, (...) there are actually 3 I/O lines on each sensor port: - 1 legacy sensor A/D with appropriate power supply on the same line. - 2 digital I/O lines, one of which can also be configured as analog in. The remaining lines are 2 GND pins (...) (20 years ago, 19-May-06, to lugnet.robotics)
 
  Re: Thoughts
 
(...) That's correct. In fact, the only completely digital sensor in the NXT set is the ultrasonic sensor. -- David Schilling (20 years ago, 18-May-06, to lugnet.robotics)
 
  Thoughts
 
While sitting in an incredibly boring IB Spanish I class this afternoon (no teacher=no work=no progress=boredom=idle thoughts), I had an idea. It may have been said already in the flood of NXT-based messages which crossed my inbox several months (...) (20 years ago, 18-May-06, to lugnet.robotics)
 
  Re: Lego Research- Please Help!
 
Glad to help... I have an interest, also, in how to use these types of products to create interest in the math/science subjects. There is so much information on the Internet and from organizations like FIRST/FLL... good luck. Jim -- View this (...) (20 years ago, 18-May-06, to lugnet.robotics)
 
  Re: RCX Virus?
 
(...) The original firmware is a very stable piece of software. The only moment that we ever had serious problems with it was linked to our robot GASTON while being used in the same room with a 10 desktop Mindstorms robotics course. Some parasite IR (...) (21 years ago, 16-May-06, to lugnet.robotics)
 
  Re: RCX Virus?
 
(...) I use rechargeable batteries too but I use Rayovac Renewals, Manganese Alkaline which have a full-charge open-circuit voltage of 1.55 and a fairly linear discharge curve (sloping downward, of course). I don't use NiMH rechargeables because (...) (21 years ago, 16-May-06, to lugnet.robotics)
 
  Re: RCX Virus?
 
Hello Jonathan, (...) No, it is extremely improbable! Here is the only "virus" for RCX I know: (URL) it requires some cooperation so that it can spread! (...) I don't think so. Did you have very heavy load on all three motor outputs? if so, there is (...) (21 years ago, 16-May-06, to lugnet.robotics)
 
  Re: RCX Virus?
 
(...) Some more info about the problem: My RCX is 2.0 and I bought it 4-5 years ago. It's been on the shelf for a while (2-3 months) and I've always used rechargeable batteries. The ones I'm using now are 2000mA NiMH. I installed the firmware both (...) (21 years ago, 16-May-06, to lugnet.robotics)
 
  Re: RCX Virus?
 
(...) I seem to remember that as well, but it was in either Java or Ultimate Robolab IMS. What language/firmware are you using? (21 years ago, 16-May-06, to lugnet.robotics)
 
  Re: RCX Virus?
 
(...) I think it is very doubtful. I have not heard of any actual evidence of an RCX virus. What software are you using? How old is the RCX? Are you using a Ver. 1.0 with A/C input? Are you using an external power transformer? Can you borrow another (...) (21 years ago, 16-May-06, to lugnet.robotics)
 
  RCX Virus?
 
I think I heard about something like this a while back. I recently built a "CNC Milling Machine" out of Lego. It's my first attempt so it's very rudimentary and doesn't look that nice. Once I made a small program to see how the machine worked, I (...) (21 years ago, 15-May-06, to lugnet.robotics)
 
  Re: A Beautiful Machine prototype and perhaps a challenge/idea
 
<snip!> (...) Oddly it seems almost all of my pneumatic ciruits end up doing that... or at least dropping to a state where they won't complete the motions and blow a hose when the pressure caps... I'd love to get an afternnon of Kevin's time some (...) (21 years ago, 15-May-06, to lugnet.robotics)
 
  Re: Great Ball Contraption
 
(...) Thanks for comments. I really appreciate the good reviews. I'm not sure about how large this sub-niche is, but I wanted to try and capture much of what is going on around the internet regarding this topic. I've already had a few hundred (...) (21 years ago, 13-May-06, to lugnet.robotics)
 
  Re: Great Ball Contraption
 
(...) Dave, In recognition of this contribution, I have written a quick review of it on OrionRobots - (URL) tell me what you make of it. --- Danny Staple OrionRobots (21 years ago, 13-May-06, to lugnet.robotics)
 
  Re: A Beautiful Machine prototype and perhaps a challenge/idea
 
(...) In the interests of full disclosure, my original plans were to use pneumatics. But seeing as I didn't have any, I had to use something else. It was in an email exchange with Cary Clark some time ago that he mentioned that a "low-tech, (...) (21 years ago, 13-May-06, to lugnet.robotics)
 
  Re: A Beautiful Machine prototype and perhaps a challenge/idea
 
In lugnet.robotics, Rafe Donahue wrote: [snip] (...) [snip] (...) [snip] How about a machine that can be turned on in more than one way and it turns itself off according to which on method is chosen? Dennis (21 years ago, 12-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) Glup, I had not notice it, you are right. The NXT RJ12 plug has printed the letters BN, but I have not found the manufacturer, I will continue searching. Best regards Gustavo Lugnet 566 (21 years ago, 12-May-06, to lugnet.robotics)
 
  Re: A Beautiful Machine prototype and perhaps a challenge/idea
 
(...) Very nice machine, I especially appreciated the windup motor trick (always wanted to do something with them, preferably odd and interesting!) Philo (21 years ago, 12-May-06, to lugnet.robotics)
 
  Re: A Beautiful Machine prototype and perhaps a challenge/idea
 
(...) Gee, I thought Bill Gates invented that? -Rob www.brickmodder.net (21 years ago, 12-May-06, to lugnet.robotics)
 
  Re: A Beautiful Machine prototype and perhaps a challenge/idea
 
(...) Turning itself off is a feature? ;oP I've spent a lot of time making pneumatic circuits that accidntally shut themselves off..... LOL! Very nice! Kevin (21 years ago, 12-May-06, to lugnet.robotics)
 
  Re: A Beautiful Machine prototype and perhaps a challenge/idea
 
(...) Very nifty! Another way would be to have a second switch that is on except when the scissors are at the bottom, and wire it in parallel with the activation switch. Sorta like how they get car windscreen wipers to always go back to the right (...) (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: NXT to NXT communication?
 
(...) Sounds like it's a firmware block though, so hopefully it can be overcome with "NxtOS" or whatever in future. ROSCO (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: A Beautiful Machine prototype and perhaps a challenge/idea
 
(...) <snip> (...) <snip> It is slightly more complicated than that. In order to make it go up slow enough to be interesting, I had to gear down the speed of the motor. As such I go from 8 teeth (I think) on the motor to the big 40 (?) teeth on the (...) (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: A Beautiful Machine prototype and perhaps a challenge/idea
 
(...) Very interesting, if a rather disturbing implementation. I had heard of the conecpt, but not seen those vids. The prosthetic is just a big creepy. (...) I like your version, first its more cute and friendly, and secondly you can see the (...) (21 years ago, 11-May-06, to lugnet.robotics)
 
  A Beautiful Machine prototype and perhaps a challenge/idea
 
Computer scientists might know of Claude E. Shannon, considered the father of digital communication. He is also less well known for his Most Beautiful Machine, a machine that, when turned on, simply turns itself off. (A version can be viewed online (...) (21 years ago, 11-May-06, to lugnet.robotics)  
 
  Re: NXT to NXT communication?
 
(...) Hmmm... Speaking of SDK, based on a preliminary version of the Hardware SDK documentation the NXT is not capable of being both a master and a slave at the same time so a network of NXTs is limited to one master and three slaves and that's it. (...) (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) Actually, I think if you look closely at the NXT connectors and the DEC ones, you will find the latch offset to the wrong side. There are many of us that have been looking for these connectors for some time now, and it seems all the existing (...) (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
Hi, the connector name is RJ-12 DEC 6P6C key it is usually used in telephony. You can find this in the link below. (URL) I found the crimping tool here (URL) this helps. Best regards Gustavo Santiago de Chile (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) Yep, I can confirm (finally, now that it's past May 1). It is a modified RJ12 connector (RJ-12 is 6 wire phone cord connector). The wiring and the jack size is the same, but the little lock piece that sticks up on the connectors is offset and (...) (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) Thanks Philo! It looks like a lot of detailed and patient work, but I believe I could ruin a few before I got the hang of it. And the RJ11 phone cables are cheap these days. Thanks for the link. Todd (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) My understanding from reading some of the posts that the connector NXT uses is a non-standard RJ-esque connector. It is not RJ11 or RJ45 but some new connector. Not an electrical engineer myself, I do not know if this connector is even (...) (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: PHOTOS POSTED Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) snip (...) Here's links to the photo scans of the pamphlet: (URL) show the cable (URL) Page one of the pamphlet (URL) Page two of the pamphlet (URL) Page three of the pamphlet (URL) Page four of the pamphlet Todd (21 years ago, 11-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) Alas, I've only seen the phone ones. I used one through a turntable with the RCX cables, but of course that's only two wires. (Actually I used all four wires and basically sent two RCX cables through the one "detangler"). I would imagine they (...) (21 years ago, 10-May-06, to lugnet.robotics)
 
  Re: NXT newsgroup needed
 
(...) As I've been one of the lucky few who have had the opportunity to play with the NXT as part of the MDP, I can tell you that these two are vastly different beasts. I've found the hardware, software, even building techniques to be significantly (...) (21 years ago, 10-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) A very flexible solution... with the only problem that it is a bit bulky. (...) Oh... nice little devices you make me discover! They would be wonderful through a technic turntable. But all of these gizmos I've seen on the web have only 4 (...) (21 years ago, 10-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) I’ll throw one more suggestion on top of that. Take a standard LEGO cable, cut it in half, and put a standard adaptor on the end (such as a RJ11). One LEGO cable can be used to produce two adaptor cables. From there you can create all the (...) (21 years ago, 10-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) If you want one at once... do it yourself ;o) ((URL) - not for the fainthearted!!!) Philo (21 years ago, 10-May-06, to lugnet.robotics)
 
  Re: NXT newsgroup needed
 
(...) Thanks, John. You've described things well. I'm holding off on creating a new group for a few reasons. One is: when more information comes to light about the NXT, it may become apparent that 'RCX' is a good place for discussion of it. (Heh, At (...) (21 years ago, 9-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) That might be because they would be manufactured by a third party... BTW, official LEGO MINDSTORMS NXT add-ons are listed here, as well as on the legoeducation website. (URL) (21 years ago, 9-May-06, to lugnet.robotics, lugnet.robotics.rcx)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) It's just got to be a matter of time before they sell this individually or in small groups of 3, 5 or a dozen, right? Todd (21 years ago, 9-May-06, to lugnet.robotics)
 
  Re: Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
(...) The converter cables have been publicly known for a while. However, they are still unavailable for individual purchase from LEGO Education, unlike the rechargeable battery which is available to purchase separately. (21 years ago, 9-May-06, to lugnet.robotics)
 
  Lego Education Pamphlet indicates a NXT to old style brick adapter cable
 
NXT Fans, In my new position at Indian River Community College I work with faculty in technical education and have joined the Robotics club. We are excited by the upcoming release of Mindstorms NXT, and I have personnally ordered my own set already. (...) (21 years ago, 9-May-06, to lugnet.robotics)  
 
  Re: NXTway
 
(...) I didn't try. Probably not well since it is quite unstable. (...) No, it's a simple on/off. The great improvement is that the contact occurs at half stroke, you don't have to push hard as with RCX touch sensors. Philo (21 years ago, 9-May-06, to lugnet.robotics)
 
  Re: NXTway
 
Very cute. I like how it fell over. How does it go on unlevel surfaces ? Now im off to build a self leveling touch sensor. Does the NXT have on/off touch sensors like the RCX or variable (analogue) sensors like a playstation controller? Steve (21 years ago, 9-May-06, to lugnet.robotics, FTX)
 
  Re: My NXT MOC
 
(...) part??? Seems an awfully high price to pay for this little guy. ;) Dave Hurley www.greatballcontraption.com (21 years ago, 9-May-06, to lugnet.robotics)
 
  NXTway
 
You liked the (URL) original>... You loved (URL) Steve's adaptation>... You'll enjoy the sequel: (URL) NXTway>! (URL) Philo (21 years ago, 8-May-06, to lugnet.announce.moc, lugnet.robotics, FTX)  
 
  Re: My NXT MOC
 
(...) As construction part, yes. But there is also a new tyre, the 55976 Tyre 56 x 26 Balloon. Good sticky rubber, but a bit soft for heavy robots. There are also a few existing parts that were not common such as (URL) (21 years ago, 8-May-06, to lugnet.robotics)
 
  Re: NXT memory limits
 
In article <IyrsyD.1qIr@lugnet.com>, Tim Byrne <sultan@KILL-the- SPAM.locehilios.com> wrote (...) Bluetooth is up to it, typical use is to connect a hands-free headset to a mobile phone. Stereo headphones are now available for listening to music (...) (21 years ago, 5-May-06, to lugnet.robotics)
 
  Re: My NXT MOC
 
(...) the only new piece in the NXT? (21 years ago, 8-May-06, to lugnet.robotics)
 
  Re: My NXT MOC
 
(...) I confirm, part# is written on the piece just below corner hole. Better be shortsighted or have a good magnifier... Philo (21 years ago, 8-May-06, to lugnet.robotics)
 
  Re: My NXT MOC
 
(...) The part # is 55615 - not sure if it is official though... Anyone else? (21 years ago, 8-May-06, to lugnet.robotics)
 
  Re: My NXT MOC
 
"John Barnes" <barnes@sensors.com> wrote in message news:Iyx488.1qHC@lugnet.com... (...) part ID? I can hardly wait until we get an official element list for the NXT. Cheers ... Geoffrey Hyde (21 years ago, 8-May-06, to lugnet.robotics)
 
  Re: My NXT MOC
 
(...) As for hints, here are some thoughts: -I found I had to break from the mindset of expecting to make connections that were either parallel or perpendicular to others. With this new approach, there are more options. - I think that the previous (...) (21 years ago, 8-May-06, to lugnet.robotics)
 
  Re: My NXT MOC
 
(...) (URL) (21 years ago, 7-May-06, to lugnet.robotics)
 
  Re: My NXT MOC
 
"Dave Astolfo" <dastolfo1@cogeco.ca> wrote in message news:IywC2s.1o0F@lugnet.com... (...) Can you give new studless technic builders any hints or tips that might help them on their way? I'd also appreciate it if anyone has photos of this new (...) (21 years ago, 7-May-06, to lugnet.robotics)
 
  Jamocklaquat to make another public appearance
 
Eric Sophie's rather cool Multi-RCX Lego Mindstorms robot Jamocklaquat is currently being exhibited at The Cathedral Arts Festival in the Grace Church Van Vorst in New Jersey until June 2nd 2006. There are pictures, and an in-depth story at (2 URLs) (...) (21 years ago, 7-May-06, to lugnet.robotics.events, lugnet.robotics, lugnet.announce, FTX)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR