 | | Re: Several RCX/Mac Q's
|
|
(...) Several Mac/Mindstorms options are covered at: (URL) use NQC myself, although since I wrote it, I'm somewhat biased. If you are even slightly familiar with C syntax, NQC should be easy to pick up. The Apple IR port can run in two mode- one is (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Machina Speculatrix Reproduction
|
|
Doug Durham wrote in message <005701be6534$358277...nd-pam>... (...) Thanks. I have improved the images that were on the page originally. It should be easier to see things now. (...) creating truly interesting (...) I agree. You can create some very (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | RE: windows CE
|
|
I started working on an RCX library for Pocket Scheme some time ago, but have not had time to finish it. At this point, it will only work with the built-in COM port - but on the Clio it's very easy to plug the IR tower into the "Travel Dock." I do (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Machina Speculatrix Reproduction
|
|
(...) Since an analog circuit can be simulated by a digital computer, I am not sure I see that an analog computer is superior for robot behavior. It may very well be that a *simple* analog circuit is superior to an equally simple digital circuit, (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Several RCX/Mac Q's
|
|
I'd like to thanks everybody who helped me get my rcx up and running on my Mac... I am now using NQC though I will probably order Robolab and/or IC in the near future just for the sake of having them. I've found that NQC/MPW is a little buggy in (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Machina Speculatrix Reproduction
|
|
John, Not to split hairs, but as you say you can only "simulate" an analog circuit on a digital computer. A digital simulation of the simple two circuit non-linear circuit contained in the Machina Speculatrix would be very very very very very very (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: windows CE
|
|
In article <Voyager.99030317455...@qnx.com>, rajackson@qnx.com writes (...) <pedant> 11 bits (1 start, 8 data, 1 odd parity, 1 stop) </pedant> (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Three-wheel Synchro Drive
|
|
(...) Even better, have both wheels powered for "forward" motion (because a single offset wheel will produce some torque then too) and allow them to rotate in opposite directions when turning the mechanism ... I'm not sure I can implement this as I (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | FW: Several RCX/Mac Q's
|
|
this needed sending to the list... # -----Original Message----- # From: rkippenhan@transactor.net # Sent: mercredi 3 mars 1999 18:01 # To: Ken Guest; hchea@ramapo.edu # Subject: RE: Several RCX/Mac Q's # # # ---...--- # ---...--- # # # I'd have to (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | The power of Mindstorms
|
|
My son and I are making experiments to determine the power of the Lego Gear motor (from Mindstorms). One finding has been that the average effect is slightly above 10 Nm measured directly on the axle, so that a Lego motor can lift 1 kg+ without (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Three-wheel Synchro Drive
|
|
(...) But are they the same? The 8422 has smooth tyres, while the RIS has knobby tyres. This image is great for reference, with a summary of all the parts in the RIS: (URL) The smooth tyres from 8422 are great for making a classical car. I have (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: The power of Mindstorms
|
|
In article <F82HpD.9F7@lugnet.com>, Franz-Michael S. Mellbin <fmm@fischer-mellbin.com> writes (...) Some time last year somebody posted a useful chart of diagonal bracing dimensions in steps of 1/3 brick. (3 - 4 - 5 etc) Does anyone have a url or a (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Proximity Temp Logger
|
|
Just posted a pic and NQC code of my latest Torbot mod - the Proximity Temp Logger. Visit (URL) and go to LEGO-> Mindstorms for more. Dave (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | PowerStation
|
|
Hi! I want to build a battery recharging station for my RCX robot. I wounder if that has been done before. My idea is to wire 2 to 3 three 9V rechargeable batteries in parallell. (to produce enough current) then connect them to the battery adapter (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Psion Electronic Organizer
|
|
Did anybody hook up a handyboard to a Psion Electronic Organizer? Maybe via IrDA interface or serial cable? Alf (28 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Psion Electronic Organizer
|
|
(...) I would like to know the same thing of the PalmIII. (...) ---...--- Shoot-to-Win Protect the 2nd Amendment ---...--- (28 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | RCX IR proximity detector
|
|
Hi all, I have gotten quite a few responses to my IRPD for the RCX project. By far most people wanted to know if I had boards/full kits that I could sell. Phew! This is a hobby, and while I don't mind putting together boards and special parts, I'm (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Compiling the compiler
|
|
Thanks Dave, I did however find a version of Bison and Flex to use under windows. I didn't want to install the whole cygwin distribution so I searched and found stand alone versions of that came from DJGPP. I'm still having a few minor (...) (28 years ago, 4-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Precise timing with the Handyboard ?
|
|
Hi, does anybody know how to measure the time between two trigger signals as precise as possible ( around 10 microseconds would be fine.) with the handyboard. Peter -- Dr. Peter Borrmann University of Oldenburg Phone: +49 441 798 3362 (office) (...) (28 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Precise timing with the Handyboard ?
|
|
(...) Use the TIC port 2 or 3. The precision of the reading you'll get is 0.5 us. About a year ago I posted some drivers to make such measurements. Tell me if you want them. cu Tom -- Thomas Hauri ZHW Zuercher Hochschule Winterthur University of (...) (28 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sharp GP2D02 code available
|
|
Thanks Barry, great work. I do have one little question: As I read the data sheet of the GP2D02 ( (URL) ) I saw some timing specifications that i think are not taken care of in your software. Please correct me if I'm wrong. The timing chart shows (...) (28 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Three-wheel Synchro Drive
|
|
Fredrik Glöckner wrote in message ... (...) The hubs are the same, tires different. The knobby tires were used on the motorcycle prior to the 8422. Eric (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Hamamatsu P5587
|
|
Does anybody have the pinouts or spec sheet for the Hamamatsu P5587 optical sensor? Thanks (28 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Big Money, Big Prizes, Who wants it?
|
|
This isn't really a Lego event, but all you roboticists should check it out! Calling All Sumo Robots! FujiSoft International, sponsor of Japan's big Robot Sumo Competition, brings the robotic action to the San Francisco Exploratorium, Tuesday March (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | RE: The power of Mindstorms
|
|
(...) Here is the thread which includes both the table and the URL to a very good site on this information. JT -----Original Message----- From: lugnet.robotics@lugnet.com [mailto:lugnet.robot...ugnet.com] Sent: Wednesday, November 11, 1998 11:52 PM (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Hamamatsu P5587
|
|
I'm not an ASCII artist, so I'll attempt a verbal description. View the P5587 with the emitter/detector side facing you and have two pins on the left and three on the right. In this position pin-1 is in the upper left corner, pin-2 in the lower (...) (28 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Power problems?
|
|
To all: I am currently constructing a Handy Board. Am I currently at the step (with the Handy Board) of testing it with the Interface/Charger board. The tests I performed earlier on the charger worked, and the tests so far with the Handy Board have (...) (28 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | LA Area Robot-Arena competition April 17th, 1999
|
|
Tired of playing by yourself? An informal Robot-Arena competition will be held in the Los Angeles Area on Saturday April 17th 1999. This will be a...er...slightly destructive Lego(TM) on Lego(TM)smashing/sho...g/whatever competition using autonomous (...) (28 years ago, 4-Mar-99, to lugnet.robotics)
|
| |
 | | LA Area Robot-Arena Competition April 17, 1999
|
|
Tired of playing by yourself? An informal Robot-Arena competition will be held in the Los Angeles Area on Saturday April 17th 1999. This will be a...er...slightly destructive Lego(TM) on Lego(TM)smashing/sho...g/whatever competition using autonomous (...) (28 years ago, 4-Mar-99, to lugnet.loc.us.ca.la, lugnet.loc.us.ca.sbe, lugnet.robotics.events, lugnet.robotics.events.robot-arena, lugnet.loc.us.ca.la.lb, lugnet.loc.us.ca.la.pas, lugnet.loc.us.ca.la.sa, lugnet.loc.us.ca.sd, lugnet.loc.us.ca.bak)
|
| |
 | | Could IR ranging sensors be used with Rug Warrior board as well
|
|
Hello all: I have to ask this question: I am using a Rug Warrior Pro board and handyboard. Could the Sharp GP2d02 or the Hamatmtsu P5507 be used on the Rug Warrior as well. More specifically : What are the voltage requirements of these two? What are (...) (28 years ago, 4-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Two servos, one input ?
|
|
Has anyone hooked two servo motors up to one input? I have a project that requires three servos, but two are an identical pulse. I was going to hook those two up as servo_a7 and run a 1000-1200mA current at 6 volts. I'm thinking that will give me (...) (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Compiling the compiler
|
|
(...) What file are you compiling when you get this error? I think the fix is to include "Symbol.h" before the array templates get instantiated, but it is curious that neither Metrowerks nor gcc complain. (...) Yes, a cast should be fine. Offhand, (...) (28 years ago, 5-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: Several RCX/Mac Q's
|
|
(...) I use NQC/MPW in OS 8.5.1 all the time, so I'm pretty sure its not the OS itself that is a problem. What sort of bugs are you seeing? Dave (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Three-wheel Synchro Drive
|
|
(...) Sure, but the original question specifically asked about the tyres, not the hubs. (...) There's one knobby tyre on the 8857 Street Chopper as well: (URL) may be hard to get, but then again, it isn't particulary exciting. IMO, anyway. Fredrik (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Re: several RCX/Mac Q's
|
|
(...) I use NQC/MPW in OS 8.5.1 all the time, so I'm pretty sure its not the OS itself that is a problem. What sort of bugs are you seeing? Dave (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Several RCX/Mac Q's
|
|
(...) NQC/MPW crashed whenever it tried to communicate with the rcx (downloading firmware, programs, etc). But now that I have disabled Virex 5.9, it's working like a gem. Thanks for the help. (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Re: The power of Mindstorms
|
|
Thanks to Peter and Jim for your references, I am sorry to see that my first posting was not accurate. We have studied these excellent pages on how to reinforce Lego structures at an earlier point (and the interesting Math behind it!). However, our (...) (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Could IR ranging sensors be used with Rug Warrior board as we ll
|
|
Hi, I can only speak for the GP2D02: voltage requirement 5 volts very low power range 10cm to 80cm beam width at maximum range is about 1cm 1 input bit and 1 output bit required Cheaper,smaller ,less power, and easier to hook up than sonar I see it (...) (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | pbFORTH enhancements soon
|
|
Thanks to all of the mail I have received, I am going to try to get the next version of pbFORTH out this weekend. Charles Anderson pointed out a rather embarassing flaw in the LCD_SHOW and LCD_HIDE routines, thanks. I have been using Dave Baum's NQC (...) (28 years ago, 5-Mar-99, to lugnet.robotics.rcx.pbforth)
|
| |
 | | Linux, and HB beta binaries: problems getting started
|
|
Handy Board list: I'm trying to get the handy board running under Linux for a robotics class at the University of Colorado. All the devel platforms are Macs but I'd like to use Linux. I'm having problems getting started, even though I've grepped all (...) (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | [Irish News] EB stance on Mindstorms
|
|
Electronics Boutique have changed their stance on their stocking of the extension kits for Mindstorms - they won't be. They will still stock the ris set but nothing else. I wish they'd just make up their bloody minds. ***...*** Ken Guest Credo Group (...) (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Three-wheel Synchro Drive
|
|
I really like the large (bicycle) wheels that came with RIS partly because they are narrow but mostly because they are large diameter. I noticed that the 8857-1 set had two fat tires which look like they are larger diameter than the RIS tires. Is (...) (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Sensor raw score and communication
|
|
you do not need to use VB the spirit OCX is just a com component like any other and can therefore be used with VC++. I also believe that it is fairly straightforward to set the sensor type in order for them to send their info in raw mode. Good luck (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Rolling Ball Inclinometers
|
|
Does anyone know of a place to get cheap rolling ball inclinometers? thanks Michael (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | 3 used HB
|
|
During the last few days I have received more then 40 offers to buy my 3 used HBs. I am almost done selling the HBs according to the criteria of geographical convenience. I am sorry for all the other people that answer to my letter. ---...--- (...) (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Three-wheel Synchro Drive
|
|
On Fri, 5 Mar 1999, it was written: (...) Well, the thing I like about those particular hubs/tires (unless the hubs are interchangeable between different tires I treat them interchangeably) is that they are tall and very thin. John A. Tamplin (...) (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Three-wheel Synchro Drive
|
|
There is an organization that does privately held auctions of batches of lego parts. Not exactly what you wanted, ie. can't get one each of 10 particular parts. But you can get let's say 20 16x1 technic beams, etc. Check out: (URL) vouch for it (...) (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | sale at eToys
|
|
eToys is having a promotion for firsttime customers of $10 off. Use coupon C6993 at checkout, and it runs until March 15th. They also have the fiber optic multiset for 30% off, and this has the fiber optic piece which can make a makeshift rotation (...) (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Linux, and HB beta binaries
|
|
Hi Edward, I am running ic on linux since December. I downloaded the _SOURCE_ from the same location as you I think, (ic-src-unix-2.860-beta.tar.Z) and build the binaries on my system to make sure they will use the libraries I have. You also have to (...) (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Linux, and HB beta binaries
|
|
I've run it on Red Hat (5.2, stock Glibc) and I'm running it now on Slackware (3.6, stock). I haven't had any problems either, but I built it from source as well. (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Rolling Ball Inclinometers
|
|
(...) It's All Electronics. 2 for $1.00. 1.800.826.5432. Page 17. Catalog numbers ATS-1 and ATS-3. No real specs for them, but both are pulls from arcade games. (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: Three-wheel Synchro Drive
|
|
Thanks Dave this looks like a promising lead. This could be useful if people don't consistently run up the prices. Like nearly every auction site I've checked out the items tend to go for more than they can be obtained through normal channels. I was (...) (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Where do I get Sharp GD sensors
|
|
Thanks for the info. I am decided on sharp, because I want to do wall following, now where do I get them. Also, where do I get some code for it, if there are any? Thanks much. (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Three-wheel Synchro Drive
|
|
On Fri, 5 Mar 1999 19:33:45 GMT, lego-robotics@crynwr.com (Jim Thomas) wrote: [Stuff about AucZILLA bids vs. accessory pack prices snipped] AucZILLA is really the premiere internet Lego parts auction. It's the biggest, it's been running the longest, (...) (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Could IR ranging sensors be used with Rug Warrior board as well
|
|
(...) I designed and etched a small adapter board that interfaces three Sharp GPD05 and one GPD02 sensors with RW. It replaces the contact bump switches with the Sharp detectors by driving voltage followers to the level of the resistor ladder used (...) (28 years ago, 5-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Compiling the compiler
|
|
(...) I've checked into this a little further. It comes down to something like the following: void foo(const char *p) { delete p; } On one hand, this is conceptually a violation of "constness" as a caller to foo() wouldn't know that the object (...) (28 years ago, 6-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | Lugnet on Toast.
|
|
Finally made a cut on the DiMill. The machine is great, but I have a program error in the spacing between LUG and NET. Also my toast was a little warped as seen in the movie. I will attempt another cut in the near future. -- Bob Fay The Shop (URL) (28 years ago, 6-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Two servos, one input ?
|
|
(...) Why do you want to have two servos doing exactly the same thing? Why can't you simply mechanically hook up the two things you want to drive the same way to a single servo? (28 years ago, 6-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Rolling Ball Inclinometers
|
|
I recall one of the surplus electronics/mechanics catologs (All Electronics? Herbach&Rademan) were selling them for $0.50 -----Original Message----- From: Michael N Rosenblatt <mr4@andrew.cmu.edu> To: handyboard@media.mit.edu (...) (28 years ago, 6-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | HB v1.2, IC v3.1 and ir functionality
|
|
I'd like to get the ir functionality working on my v1.2 handy board. I am using the 3.1 version of IC from newton labs. See below for the files included with this release. According to The Handy Board Technical Reference" Dated Jan 16, 1997, I must (...) (28 years ago, 6-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Where do I get Sharp GD sensors
|
|
I ordered mine from Acroname Inc. for $19.00. They also have sample code provided by Gary Livick. I haven't connected it to the handyboard as or this time but will be intersted to know how everyone else is doing it. Mine is a model GP2D02. Good Luck (...) (28 years ago, 6-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Idle process
|
|
I am reworking parts of the task scheduler in tm.c, tm.h, et al. I notice, reading the code, that there is an idle process which runs all of the time. There is a note in tm.c; "execi needs pd_idle". It appears to use it to locate the head of the (...) (28 years ago, 7-Mar-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: sale at eToys
|
|
In article <199903070836.AAA289...bcon.com>, Brian Nakata <bnakata@cybcon.com> writes (...) Brian, You may not have read the conditions of use of this group on (URL) but they include the words :- "It is a condition of your use of the discussion (...) (28 years ago, 7-Mar-99, to lugnet.robotics)
|
| |
 | | Fw: sale at eToys DO NOT SEND LARGE ZIPS !!!
|
|
Brian Nakata, Please remember: Not all users on the lego-robotics are working with a palmpilot, so please stop mailing large ZIPs !!! Instead, mail a message to the mailing list saying you have these zips, and that you can send them to everyone (...) (28 years ago, 7-Mar-99, to lugnet.robotics)
|
| |
 | | Ultimate Starter Sets / Add-Ons for Mindstorm? Reprise
|
|
Greetings all, Looking for feedback on the following scenario: No Prior Lego parts No Prior Lego Experience Recently Aquired The folowing Sets: Mindstorm (A Present) ExtremeCreatures - (Purchased - live and learn) RoboSports - (Purchased - live and (...) (28 years ago, 6-Mar-99, to lugnet.robotics)
|
| |
 | | Newbie questions
|
|
Hi, Since I don't have the RIS yet (not available in Australia for a few more weeks), where can I find out what parts are in the add-on packs (similar to this one for the RIS (URL) ? Where can I find S@H on the net ? Do they ship overseas, or anbody (...) (28 years ago, 7-Mar-99, to lugnet.robotics)
|
| |
 | | Electrical Components
|
|
I am looking to purchase a transducer for measuring distance that can be used with the RCX. Seems to me that I have seen discussion on this before. Anyone know where I can make this purchase? (28 years ago, 5-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Ultimate Starter Sets / Add-Ons for Mindstorm? Reprise
|
|
I would go for the Space Shuttle. It's 1.300 pieces with lots of good ideas, useful techinic parts and a few nice extras like the mini-motor and strobe light. (...) ... (...) Play well! Franz-Michael S. Mellbin --- fmm@fischer-mellbin.com (URL) (28 years ago, 7-Mar-99, to lugnet.robotics)
|
| |
 | | More Output ports!
|
|
Hi All - I posed a question a couple of weeks back about using small relays to switch control of outputs in order to use more motors. Since nobody said they had done it, I went ahead and bought some parts from Radio Shack, and built a small (...) (28 years ago, 7-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Ultimate Starter Sets / Add-Ons for Mindstorm? Reprise
|
|
fyi- I've posted inventories of a bunch of older Technic sets at (URL) least this way you can see what you'd be getting with each set. I believe these inventories have been duplicated at www.lugnet.com (along with many others). Dave (...) (28 years ago, 7-Mar-99, to lugnet.robotics)
|
| |
 | | RcxCC for NQC 1.1?
|
|
I just downloaded RcxCC and noticed that it is still using NQC 1.0b4 Was the RcxCC project abandoned? Why it still uses an outdated version of NQC? Are there any other good alternatives to RcxCC for the new NQC? Thanks Laurentino Martins (...) (28 years ago, 7-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | stepper motors
|
|
Hi : I am looking for a stepper motor that works at 7V. I was wondering if any of you have used stepper motors for the handyboard or the Rug Warrior. If so, what model did you use and what was your selection criterion for the motors. Thanks. (28 years ago, 7-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: sale at eToys
|
|
Dear Arsehole (AKA Brian) Thank you very very very much for the binary posting of several large zip files. I was completely uninterested in receiving some nonsense about PalmPilots (perhaps this an appropiate item for a five-knuckle-shuffler such as (...) (28 years ago, 7-Mar-99, to lugnet.robotics)
|
| |
 | | Re: More Output ports!
|
|
I would be interested in seeing what you have done. How do you control the switch, with the third RCX output ? -- SeeYa ! ---...--- Jim ---...--- Hello... Is this thing on ? John Brubaker wrote in message <36e2aace.12707929@l...et.com>... (...) (28 years ago, 7-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Sharp GP2D02 code available
|
|
Hi Barry, I have a GP2D05 from Acroname Inc., Have wired as per instructions black for gnd., green for Vin, Yellow for Vout, and red for Vcc.The pin outs are different than the GP2D02. Then installed the diode and connectors for the handyboard .as (...) (28 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sharp GP2D02 code available
|
|
I just finished sending a question to the mail list but may have my problem fixed? Just from blind luck. I have digital out #7no the expansion board and digital in#15 on the main board and the first of the zeros on on the LCD changes to a one at (...) (28 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: More Output ports!
|
|
Please post all that you have. This is very neat! Thanks, Dan (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Robotic helecopters anyone?
|
|
Just taking a minute away from senior project hell to tell everyone about something we came across while searching for a motor. (URL) A nifty and well-though-out four-corner helicopter, with an attractively bare platform in the center. Too small to (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Idle process
|
|
Hi Lou, the sleep instruction effectively shuts down the CPU until the next interrupt occurs. Thus, the idle process conserves battery power if no task wishes to run. I consider this a worthwile feature. If you can do this without a dedicated idle (...) (28 years ago, 8-Mar-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Ultimate Starter Sets / Add-Ons for Mindstorm? Reprise
|
|
Franz-Michael S. Mellbin wrote in message ... (...) ideas, (...) Hi. I mostly lurk about. And I especially perk my ears up at these "what should I get to bootstrap myself" threads, since I was out of LEGO for the last 15 years, only restarting with (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Re: More Output ports!
|
|
I actually use my RCX to control relays in my large interactive art projects (blasphemy). But I imagine that it would be easy to convert my ideas into a simple way of switching motors. By putting a small relay 5 volt relay (preferably one that locks (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Re: sale at eToys
|
|
I apologize profusely for this. I was trying to send some Palm Pilot software of mine to my work E-mail. I have no idea what happened. I have never posted to this group yet (been lurking since it was started). -----Original Message----- From: Peter (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Sensor raw score and communication
|
|
(...) Benoit Cerrina, Thank you for your information. I have just send an email to Dave Baum regarding how to set the sensor in to the raw mode before I read your mail. Anywhere, I have a few question here where I hope you or other people in this (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Are GP2D02 available in Australia
|
|
Hi all, Can anybody tell me from where I can get GP2D02 in Australia. Sincerely Javaid Iqbal (28 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: Sharp GP2D02 code available
|
|
Terry, Understand that the GP2D05 is a different device than the GP2D02. For the '05' you can set a analog threshold and the digital output read 1 or 0 depending whether the distance is according to this set threshold. The '02' device has a real (...) (28 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Java and 68hc11
|
|
Thanks, I downloaded all, and now i'm trying to make it run. Very, very interesting... ---...--- From: Pierre Deprost <Pierre.Deprost@Advalvas.be> To: Stefano Falconetti <falconetti@sigma.it> Subject: Re: Java and 68hc11 Date: 03 March 1999 22:20 (...) (28 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: Ultimate Starter Sets / Add-Ons for
|
|
# From: kiplingm@javanet.com # Sent: dimanche 7 mars 1999 11:07 # To: lego-robotics@crynwr.com # Subject: Ultimate Starter Sets / Add-Ons for Mind # ---...--- # Greetings all, # Looking for feedback on the following scenario: # # # No Prior Lego (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Re: More Output ports!
|
|
With careful design, you could also use your 3rd (relay control) port for controling a motor in one direction in each state. If you were really desperate you can blast some power out from one of the inputs too :) If you could use an input to control (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Sharp GP2D05?
|
|
I have used the Sharp GP2D05 with the Handy Board and found it to be extremely simple to use. It is easy to control in either IC or in assembly language and easy to adjust for range. There is a tiny potentiometer on the back of the unit that you (...) (28 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: sale at eToys
|
|
Does anyone know which micro motor is in the 6979 set below. (I prefer the 5225 gear motor.) Looks like mostly specialized parts however. E-toys has it for 49.99 for the moment. Is it worth the motor and fiber optic? Canned Description from E-Toys: (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Serial Routines
|
|
Hi, I have the following questions: I want to transmit data by a radio comunication beetween HB and PC (only HB to PC right know) using the pa7 and a one-way wireless link from Conrad Electronics (german electronic reseller). Do i need the pa7_9600 (...) (28 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: sale at eToys
|
|
Who's this idiot who doesn't know how to behave in a mailing list? It took me twenty minutes to download your shit and I pay for online time, you know? -Daniel ps: Brian, sorry for calling you an idiot, but you deserve it. -- Did you check the web (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Robots on the History channel
|
|
If you didn't know, the history channel ran a two-hour special on robots through history. It was pretty damn cool to see some of the _ancient_ automatons. Check your local listings if you get the History channel to see if they are re-airing it (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | 20 X 8 L.C.D driver?
|
|
I have seen questions on the list about using a 20 X 8 instead of a 16 X 4 lcd, I think that the person was told to look on the handy board site for a 20 X 8 driver. has anybody used a 20 X8 lcd and if so how did you do it and could you help me use (...) (28 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | HB & unmanned vehicle system
|
|
Hi, can anyone help me in devolping an unmanned ground vehicle system using a Hand Board? This is my first experience with the HB, in fact, I'm actually buying it (sorry, but may be you can also tell me where to by one by the internet and what to (...) (28 years ago, 8-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Robots on the History channel
|
|
My son and I watched it and it was excellent! He's been a bit frustrated with his Mindstorm set lately and watching the show renewed his determination to master it. I wish I could have taped it but the VCR is on the fritz. I'm hoping thatit runs (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Re: RcxCC for NQC 1.1?
|
|
Can you simply replace the nqcc executable in the RcxCC directory with the new version? (...) (28 years ago, 8-Mar-99, to lugnet.robotics.rcx.nqc)
|
| |
 | | RE: Robots on the History channel
|
|
The history channel has a website. This link will take you to where you can buy the video for $30. Or call 800 408-4842. The program was one of the Time Machine series. (URL) it does not look like it is going to run again in the next few weeks. JT (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Fw: Robots on the History channel
|
|
It was a cool show, but unless you are truly obsessed, I am not sure it is worth $30. Try this. Go to you local library(in the US) and ask for it. If they don't have it, give them the ISBN# and ask them to order it. I think US public library policy (...) (28 years ago, 8-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Lego MindStorm for 10 year-old?
|
|
I dunno, I bought Mindstorms for my 2 year old daughter and she seems to enjoy it... Dethe Elza (URL) you check the web site first?: (URL) (28 years ago, 8-Mar-99, to lugnet.robotics)
|