To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *12001 (+100)
  unsubscribe help
 
I lost my directions on how to unsubscribe and the email address that I send it to could you please help (27 years ago, 10-Jun-99, to lugnet.robotics.handyboard)
 
  Bad Memory ? Help!!!
 
Hi I trie to use the 62256BLP-10, instead of the 62256LP-120. And it didn´t work on the Handy board, but download program on the PC, said that the download was fine "Reboot the board", then I unplugged the Memory Chip, and tha same thing happend. (...) (27 years ago, 10-Jun-99, to lugnet.robotics.handyboard)
 
  Re: A synchro-drive and a CyberDog
 
Mario Ferrari wrote in message ... (...) WOW! (...) feel (...) You're welcome. You've taken it to a whole new level. My bot was so primitive compared to yours. And another thing, my PodRacer bot pulls the string. That is the podracer engines (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Removing red led from light sensor..
 
I think I read someplace that if you remove the red led from the light sensor it works much better. Has any one done this and if so how did it work? (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Trouble getting VB sample prog working
 
Hello, I've been having trouble getting a couple of the various sample VB programs to work (such as the one that can be found on the official Mindstorms site) - every routine call seems to be coughing up this error: "Remember to call Init Comm or (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Blocking IR
 
Before I start trying to do this, does anyone know why the LegOS function write_ir is a blocking function? I'm trying to write an IR detection system but am unable to do so in LegOS because every time I write a byte to the IR port the RCX locks up. (...) (27 years ago, 10-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: A synchro-drive and a CyberDog
 
In lugnet.robotics, Hari Wiguna writes: <snip> (...) Yes, correct. You "drive" it more or less you'd do with a real dog. And when you pull up the leash, it stops. Mario (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: Removing red led from light sensor..
 
(...) Ralph Hempel describes some non-destructive tricks to get better readings from a light sensor. This is the address: (URL) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: Removing red led from light sensor..
 
It is actually easier to just place a beam in front of the sensor. The layout of the hole on the beam will block out the LED adn allow you to just use the sensor. DAN In a message dated 6/10/99 6:42:02 AM Eastern Daylight Time, mario.ferrari@edis.it (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Fw: HOW TO UNSUBSCRIBE
 
-----Original Message----- From: Fred G Martin <fredm@media.mit.edu> To: handyboard@media.mit.edu <handyboard@media.mit.edu> Date: Wednesday, May 12, 1999 7:33 AM Subject: HOW TO UNSUBSCRIBE (...) (27 years ago, 10-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Removing red led from light sensor..
 
Patrick Lawrence <pat@hpnc.com> wrote in message news:FD3pFv.DDF@lugnet.com... (...) Removing the LED makes it work over a wider range (0 to 100), but probably at a slight loss of low light sensitivity. There is an analysis of the subject in the (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  RE: RCX Tower Internals
 
Kekoa wrote... (...) This might be a really simpleminded circuit. As far as I can tell there are a pair of 132's (simple HC logic chips) - one for each direction. They implement direct echo back, which implies that the channel is really only half (...) (27 years ago, 10-Jun-99, to lugnet.robotics.rcx)
 
  IS THERE ANYONE ON THIS LIST FROM ISRAEL???????
 
IS THERE ANYONE ON THIS LIST FROM ISRAEL??????? -- Clay Aucoin (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Robotic Pool Cleaner (Non-Lego Alert!)
 
For all you Hoover robotic vacuum cleaner fans, here's a company making a variety of underwater models to sweep your swimming pool: (URL) This is interesting because, unlike the Hoover model, this one follows a specific pattern to methodically (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  The ULITMATE LEGO Storage containers from Israel!!!!
 
IS THERE ANYONE ON THIS LIST FROM ISRAEL????? I found the perfect sotrage containers for LEGO's. The only problem is that they are manufactured in Israel and distributed very scarce in the U.S. The company name is "ZAG" and the product name of the (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
(...) Wow! 216 cubic feet of LEGOs! -- Did you check the web site first?: (URL) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: Removing red led from light sensor..
 
lego-robotics@crynwr.com wrote in message <5dfe79ce.2490fda6@aol.com>... (...) layout (...) the (...) This is a great idea which works pretty well. I particularly like it because it uses 100% genuine, unmodified Lego(TM) parts, FWIW. The caveat is (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: Removing red led from light sensor..
 
Actually, I heard about this (the beam in front of the red LED) a few months ago and my first reaction was, "Well, given that the problem (as I understand it) is that the red LED bleeds light internally over to the sensing LED side and that causes (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
I recommend RolyKits, which I've found to be extremely useful. They have lots of compartments, they pack up fast, and the pieces don't get scrambled between compartments. They're available at QVC online and other places: (URL) a quick search on (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
oops...I meant inches not feet. thanks for the heads up. -- Clay Aucoin Nick Taylor <lego-robotics@crynwr.com> wrote in message news:375FDA8A.7C7B03...ame.com... (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
Is there anyplace that has a picture of the products? -- Clay Aucoin Jonathan Knudsen <lego-robotics@crynwr.com> wrote in message news:3.0.5.32.199906...net.com... (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
Found pictures of the RolyKit: (URL) exactly what I had in mind. Doesn't that take up a lot of desk space? -- Clay Aucoin Clay Aucoin <caucoin@cruiseshoppes.com> wrote in message news:FD4CEM.DHy@lugnet.com... (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
Yes, QVC has pictures. (...) -- Did you check the web site first?: (URL) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Hi
 
Thursday, 10th day of June, 1999, 12:18 AM, EST. Hi, I recently joined the HB club by buying a pre assemebled HB. I soldered the battery pack terminals to the HB (yes I checked the +ve and -ve terminals). However, when I try to follow the (...) (27 years ago, 10-Jun-99, to lugnet.robotics.handyboard)
 
  RE: Removing red led from light sensor..
 
I have removed the LED from my light sensor. It turns it into a different type of device. It turns it into a passive device rather than an active one. In a pitch black room, with a white piece of paper with black lines on it, the device *with* the (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  RE: The ULITMATE LEGO Storage containers from Israel!!!!
 
An easily available (in the US at any rate) option is fishing tackle boxes. I use a large Plano Box with a well-divided lid, and half a dozen smaller ones inside. Plenty of divisions, (I have practically everything sorted by size, colour etc. - so (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
I have about 8 clear Plano boxes that everyone is talking about, but when those are laid out for easy access, there is virtually no workspace to build. I'm going to have to take some pictures and post them to get the idea across... -- Clay Aucoin (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
I understand your concern about desk space. I build on the floor. What I like about RolyKits is that, when they're closed, you can shake them and turn them upside down without worrying about the parts falling out of their compartments. I don't think (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: Hi
 
Satish: The fact that the red and green leds in the lower left corner do not light up and than shut off after ~1/3 sec. means that your board does not reset and goes into download mode. This is the reason why the downloader states: "Wrong Port or (...) (27 years ago, 10-Jun-99, to lugnet.robotics.handyboard)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
(...) -Unfortunately they're also expensive - US$15 to $40! I got my storage containers at Home Depot. I don't recall the brand, but they're orange plastic with translucent plastic tops, compartmentalized, the compartments are different lengths but (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: RCX Tower Internals
 
(...) I'm pretty sure the echo is not direct, it goes out through the emitters and back into the receiver. This is demonstrated by varying the lighting conditions and/or the baud rate and noting the response. If the echo were direct, you'd receive (...) (27 years ago, 10-Jun-99, to lugnet.robotics.rcx)
 
  Re: Blocking IR
 
(...) Do you mean dir_write? This is a problem with LegOS only. If you want non-blocking writes, comment out (in version 0.1.7 at least): while(dir_tx_state==TX_ACTIVE) ; // FIXME: scheduler integration if(dir_tx_state==TX_OK) return len; // (...) (27 years ago, 10-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: Blocking IR
 
(...) I forgot to mention. At the top of dir_write, you probably want to add: if (dir_tx_state == TX_ACTIVE) return -1; Or something to that effect, so you don't transmit a second message while a first is still transmitting, and so you have a way of (...) (27 years ago, 10-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: Hi
 
I don't know if the code gets corrupted, but the LED's do not do what they are supposed to do in download mode once in a while. Regardless of the lighting of the LED's, I am still able to download the code into my handyboard and keep on 'botting! (...) (27 years ago, 10-Jun-99, to lugnet.robotics.handyboard)
 
  (canceled)
 
 
  Re: Motor Sensor (fwd)
 
(...) What about spinning objects? A spinning object is NOT necesarely forced in circular motion by external force. Try spinning the a wheel, then stop forcing it - it will continue to spin. If you force an object in a point which is not the center (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Rolykits
 
Ok, first time on list, but I became interested in the Rolykits, so I searched and I found them. You can order on-line (is there any any better way?) from: (URL) search for Rolykits and they have two sizes: small and large. And while I was there, I (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: micro motor sometimes stuck
 
(...) does. Use it only for low-torgue applications, and try not to stall it. -- Did you check the web site first?: (URL) (27 years ago, 8-Jun-99, to lugnet.robotics)
 
  Re: Removing red led from light sensor..
 
Jeff Blaine <jblaine@shell2.shore.net> wrote in message news:slrn7lvneh.n11....ore.net... (...) A simulation of the LEGO Light sensor circuit I did in PSpice showed that the sensor wouldn't read down to zero just because the way the LED interacts (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  EEPROM burner
 
I apologize for this to those who mind. It *is* a bit off topic, but I have tried all other avenues available to me with no luck. I'm looking for a person who has an EEPROM burner or the schematic for one (If I had the schematic I would build one (...) (27 years ago, 10-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Robotic Pool Cleaner (Non-Lego Alert!)
 
I got a private reply from Bill Leggett about this device: (...) So it sounds like this thing boils down to some very clever mechanical engineering, but no software or electronics or anything. Still interesting to a robotics fan, but in a different (...) (27 years ago, 10-Jun-99, to lugnet.robotics)
 
  Re: micro motor sometimes stuck
 
(...) Well, I thought the reason that we always attach that pulley-with-rubber- lining thing (See (URL) for "friction pulley") to the micro motor is to avoid stalling the motor -- If the torgue is too high the friction pulley will slip. Apparently (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Re: Memory & Sound Detection
 
Dear Jose, (...) I believe that there is an unload command, with syntax unload <filename> Please verify it. Yours sincerely, Nitin (27 years ago, 11-Jun-99, to lugnet.robotics.handyboard)
 
  Re: micro motor sometimes stuck
 
Wow. I never noticed the rubber in those pulleys before. So you insert the axle just far enough to engage only the rubber lining? It seems that if you put the axle all the way through there is no slippage. (...) -- Did you check the web site first?: (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Re: micro motor sometimes stuck
 
The micro motor doesn't have an axle output, just a standard stud. David Kadansky wrote in message <3760AC13.5079426F@p...ox.com>... (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  (canceled)
 
 
  Lego Mindstorms in China
 
I have heard that M.I.T. students are comming to China to set up a Lego Robotics League. I would like to talk to some of the students in Beijing so that they can give me ideas for projects for the new Mars Pathfinder. I will make a new robot for you (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Sorry for the double posting
 
Hi Todd (or anyone else in charge), I was with Marcus when he wrote the two letters on Mindstorms in China. First he posted one - and got an error message. Later he posted a new one - and got another error message. After that I wanted to re-submit (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Re: micro motor sometimes stuck
 
(...) I recall reading somewhere (but I can't remember where) that the micro- motor has an internal switch to protect it from stall current. If you hold it up to your ear when it's stuck and apply power, you can hear a small click, I think. Haven't (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  Re: Sorry for the double posting
 
(...) Franz-Michael, Do you recall what error message Marcus received when he posted? Also, is it possible that he pressed the 'Esc' key or the browser's 'Stop' button while posting the first message, upon realizing that it was missing his site's (...) (27 years ago, 11-Jun-99, to lugnet.robotics, lugnet.admin.general)
 
  Re: micro motor sometimes stuck
 
(...) The slippage is supposed to occur between the micro motor and the pulley, not the pulley and the axle. The micro motor uses a stud (rather than an axle) as its output, and you insert that stud into the rubber lining. Cheers, Hao-yang Wang (27 years ago, 11-Jun-99, to lugnet.robotics)
 
  adam@hpnc.com
 
I went to helitex today and they has sent out a check yesterday by mail. I should get it monday I think. Also Gary said that it is still not emailing him the orders. Didnt you say you changed the email address to heli212@waymark.net Could you please (...) (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  Thanks ...Re: Removing red led from light sensor..
 
Thanks for all the advice. I got the parts from radio shack and just made a new light sensor today. Now its time to start working with NQC or GORDON'S BRICK PROGRAMMER or somthing. Patrick Lawrence wrote in message ... (...) (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  GORDON'S BRICK PROGRAMMER
 
Just wandering if any one was using GBP? (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  Wheel Setup for the 8880
 
Has anyone came up with a good way to use the wheel assemblies that come with the 8880 with smaller tires (the 68.8 x 40 Q)? -- Clay Aucoin (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  sorry about the message to adam longggg day
 
(27 years ago, 12-Jun-99, to lugnet.robotics)
 
  Re: Wheel Setup for the 8880
 
(...) It is probably not feasible. You may note, however, that the 2x2 round plate with cross axle hole fits into the hole in the white steering gear from 8880. Perhaps this fact can be used for something useful? Let us know if you can get something (...) (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  Re: Wheel Setup for the 8880
 
Yeah but only the posts fit..and not really that good.. (...) -- ---- Clay Aucoin (27 years ago, 12-Jun-99, to lugnet.robotics)
 
  Question about interrupt driven serial port input queue available for testing
 
Hi pals, I downloaded the package for interupt driven serial queue from the website ((URL) I tried to run the demonstration file as instructed. But i didn't understand which communication application should be used for this purpose. Can any one (...) (27 years ago, 12-Jun-99, to lugnet.robotics.handyboard)
 
  Re: GORDON'S BRICK PROGRAMMER
 
(...) Gordon's Brick Programmer is easy to use. You have way more command choices than in Lego Mindstorms and the commands are easier to use. It also does not take as much time making a program on Gordon's Brick Programmer as on Lego Mindstorms. You (...) (27 years ago, 13-Jun-99, to lugnet.robotics)
 
  Precision Resistor?
 
lynneg@dbn.lia.net Hi, I'm trying to build a HandyBoard up from scratch and am having a few problems with certain parts. Very few companies sell the 3.83K presision resistor (R4) or only at an extremely high prices. Would it be possible to replace (...) (27 years ago, 13-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Precision Resistor?
 
I actually used a small 5K POT (precision, multiturn), and tuned the output for 38 KHz. Hope it helps. K.L. McKinnon (...) (27 years ago, 13-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Problems with RCX, ROBOLAB and Macintosh
 
Hallo, I have tried NEW batteries in ir tower and RCX. I have tried to communicate in an absolute dark room with the same results. The ir tower is in near mode and the RCX in reset mode (take out the batteries and switch on the RCX - put the (...) (27 years ago, 6-Jun-99, to lugnet.robotics)
 
  Are there any limitations/restrictions on releasing legOS compiled programs (.srec files)?
 
Are there any limitations/restrictions on releasing legOS compiled programs (.srec files)? I'm aware that legOS itself is MPL (Mozilla Public License), but are the programs that are compiled with it, and contain a portion of it, subject to open (...) (27 years ago, 13-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: Are there any limitations/restrictions on releasing legOS compiled programs (.srec files)?
 
I am not a lawyer, but I have been interested in license issues for some time. Because LegOS is basically a library and not really an OS, and because it is compiled in with the rest of your code, technically speaking you must release code to anyone (...) (27 years ago, 14-Jun-99, to lugnet.robotics.rcx.legos)
 
  Anyone have any luck making a successful floating boat?
 
I was just wondering if anyone has had (or even tried) making a successful floating boat (not using the "Boat Really Floats" pieces)? -- Clay Aucoin (27 years ago, 14-Jun-99, to lugnet.robotics, lugnet.build)
 
  Fw: Problems with RCX, ROBOLAB and Macintosh
 
I've seen this thread going, and going, and going; must be pretty frustrating. It seems like you said at one point that it works fine from a PC, is that right? If so, don't you have to use a serial adapter to connect the IR tower to a Mac? And if (...) (27 years ago, 13-Jun-99, to lugnet.robotics)
 
  Re: Blocking IR
 
Great, I'll try this out tonight. Many Thanks, Phil. (...) (27 years ago, 14-Jun-99, to lugnet.robotics.rcx.legos)
 
  Re: Problems with RCX, ROBOLAB and Macintosh
 
Hallo Will, it can't be the adapter cable which is wrong. With NQC -the very good programming software from Dave Baum- I have no problem to contact the RCX. Downloading the firmware, sending programs, starting programs ... it's okay. Everything (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Re: Anyone have any luck making a successful floating boat?
 
(...) I've considered using empty air tanks from pneumatic LEGO sets as sort of 'pontoons'... my one quick test of this so far was too top-heavy (I only have three air tanks), but it seems like it should work, as long as the floats are far enough (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  serial
 
Hi, I am also having some problems with serial communications. I am trying to send information back and forth between linux and the handyboard. I wrote a simple serial sender for linux and have been trying to send to the handyboard. I have two big (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  RE: The ULITMATE LEGO Storage containers from Israel!!!!
 
(...) I'm in Holland and have to agree with you that these ZAG things are indeed great. Actually the ones (4) I have are a set of drawers on wheels (Roll'n Store, featured at (URL) You can also take them apart completely and reorganize the layers, (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Motorized Cyberslam Cannons
 
-Has anyone come up with a good, _compact_ way to use a motor to trigger Cyberslam cannons? I'm still working on my Lego Mindstorms Ogre project, and it's got six cannons serving as the missile launchers on the back half. Space is kinda tight. -JW (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Re: Anyone have any luck making a successful floating boat?
 
From: Erik Eckhardt <esquared@antispam.jps.net> (...) When I was a kid Lego boats came with a large keel piece which was quite heavy (filled with iron or lead?) and effective at putting the CoG below the water line. I don't know if the current boats (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Re: Wheel Setup for the 8880
 
(...) I don't think I understand what you mean with that. Anyway, if you're interested in making independent front suspension, I have a couple of ideas here: (2 URLs) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  H-bridge
 
Hello, Does anyone know if there is a vendor that sells a H-bridge that is ready to be used for the Handy-board, instead of me having to wire up a National Semiconductor LMD18200. Thanks for your time guys. Juergen Lunkwitz Drexel University (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Motion sensor
 
Hello all, Thank you for all of your kind help in the past. Here is another question that I hope is worthy of your time... I have a motion sensor purchased from Acroname (Eltec, I forget the part number). It works, as I had written a small program (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Motorized Cyberslam Cannons
 
I have a bank of four triggered by cams on an axle. It's 12 studs wide. The axle is driven by a chain drive. I'm using a rotation sensor to control individual firing. Sorry, no digital camera, no photos. (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Re: Lego Network Protocol questions
 
Ralph Hempel wrote in message <000001beb0e4$f9d0df...pro150>... (...) I'll back you up on this as well. I did some experiments using two towers connected to two different PCs, and found that I could send raw bytes from one PC to the other without (...) (27 years ago, 14-Jun-99, to lugnet.robotics.rcx.legos, lugnet.robotics)
 
  IRPD sensors
 
I have gotten some Infrared Proximity Detectors (IRPD), but no instructions for using them with the handyboard. These are set up with an infrared LED on each type of the sensor, and they are intended to give left/right/front detection. The program (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Re: serial
 
Monday, 14th day of June, 1999, 12:32 AM, EST. On similar note, does anybody know how I can set up the baud rate on my Win 95 machine? -Satish. (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Re: IRPD sensors
 
Evan, Who is the supplier (manufacturer) of your board, and what is the part number? Gary Livick (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Lego Network Protocol questions
 
(...) My planned solution for being to able to have constant reception involves a little bit of non-Lego hardware. The IR receiver that comes with the Mindpath IR-50 remote control is completely capable of receiving the IR stream that Lego sends. It (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Re: H-bridge
 
I think that the Robot Store ( www.RobotStore.com ) sells a variety of H-Bridges. I had no problem wiring up my own LMD18200's , however! As a matter of fact, I obtained 2 LMD's for free from the Natinal Semiconductor Website through their sample (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Battery options?
 
I was wondering what are my options for the HB battery. Would it be possible for me to get 2 battery holders each carrying 4 cells each and fill them with regular NiCad cells say, The one's they have at radio shack? Would this be a viable options to (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Battery options?
 
(...) Should work fine. If you use the "Zap" charge mode, make sure the NiCad's are designed to work on fast charging. Some are, some aren't. Also, make sure you buy them and dispose of them as a set. If you start mixing and matching NiCad's, you'll (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Question about interrupt driven serial port input queue available for testing
 
raj, I assume you could use windoze Hyper-terminal. Matt -----Original Message----- From: raj k <robo_helpmate@yahoo.com> To: handyboard@media.mit.edu <handyboard@media.mit.edu> Date: 13 June 1999 00:35 Subject: Question about interrupt driven (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Motorized Cyberslam Cannons
 
(...) There's a "space tank" (the kind your Ogre eats for supper:-) on my web page that uses a motor to trigger a Cyberslam cannon: (URL) wanted a cannon with adjustable elevation, and I fear the design is not as compact as you would like. I'm sure (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  emulegOs ported to Linux/Unix platforms
 
Mark Falco completed the first port of emulegOS to the Linux/Unix platforms. He did the gui with Tcl/Tk, a popular scripting tools available for many platforms including Win and Mac. This version will probably become the *standard* version of (...) (27 years ago, 14-Jun-99, to lugnet.robotics.rcx.legos)
 
  about interrupt driven serial port input queue available for testing
 
Thank you mat for your advice. But i coudn't under stand what should i do with the dial-up that is required for the hiperterminal connection. With out establishing a conection i can't use hyper terminal i guss. Could you please give some detailed (...) (27 years ago, 14-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Anyone have any luck making a successful floating boat?
 
(...) I've been wondering about that too. Any replies? (...) (27 years ago, 15-Jun-99, to lugnet.robotics)
 
  Re: Problems with RCX, ROBOLAB and Macintosh
 
Maybe u should stop using a Mac! : ) Trolltruck (...) (27 years ago, 15-Jun-99, to lugnet.robotics)
 
  Re: The ULITMATE LEGO Storage containers from Israel!!!!
 
I've taken every route that I could possibly take without posting. I've followed the IP for that URL that you gave all the way back to the person who manages the server and I've gotten no response from them yet. As for Home Depot, the manager says (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
 
  Re: Anyone have any luck making a successful floating boat?
 
A few came back. One was to use the pnuematic air tanks, sounds good but: 1. the only way to get them is to buy complete usually expensive) sets. 2. they probably wouldn't allow the boat to go very fast. Another was to put a plastic bag at the (...) (27 years ago, 15-Jun-99, to lugnet.robotics)
 
  (canceled)
 
 
  Re: about interrupt driven serial port input queue available for testing
 
Just configure your Hyper terminal to use dirrect connection to COM 1 or 2 instead of the modem! (...) (27 years ago, 15-Jun-99, to lugnet.robotics.handyboard)
 
  Re: Motorized Cyberslam Cannons
 
Please forgive me for being a dumb-ass, but what is a cyber-slam cannon? Don't think i have seen one? Goblintrain (...) (27 years ago, 15-Jun-99, to lugnet.robotics)
 
  Re: Anyone have any luck making a successful floating boat?
 
test -- Clay Aucoin Clay Aucoin <caucoin@cruiseshoppes.com> wrote in message news:FDCDwy.Axs@lugnet.com... (...) blow up (...) successful (...) (27 years ago, 15-Jun-99, to lugnet.robotics)
 
  Re: Problems with RCX, ROBOLAB and Macintosh
 
Hey, macs are the bomb. Given I have both and am currently on a PC, but without the mac, there would be no windows. MS stole the idea of the GUI from Apple(Who stole the idea from Xerox, who might have stole it from someone else) KGB AgEnT #4 OUT -- (...) (27 years ago, 15-Jun-99, to lugnet.robotics)
 
  Announcement: OnScreen Programming for Legos RCX
 
(URL) readme.txt (ASCII version of web page, note some of the content reads especially better on the web, or using a fixed spaced font): OnScreen Programming version 1.0 for Lego Mindstorms Once installing this system, the Lego Mindstorms RCX can be (...) (27 years ago, 15-Jun-99, to lugnet.robotics.rcx.legos, lugnet.robotics)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR