| |
It's a good thing somebody sent me this one.... Thanks J1.
The Enfield model shop orders it's pieces from the stores of the production
runs. While it was possible to have a custom run made for a large (20+ K8's.
A K8 is approximately a 2'x 1'x 1' box) order, we had to pay for the production
run necessary to do this and that was always cost prohibitive. In general we
ordered bircks out of the stores in multiples of K3s, K5s, and K6s and K8s.
(Size is in multiples of 2. (2)K3s make a K5, (2)K6s make a K8. We did have
the ability to order from more than just our molding hall in Enfield, but those
ocean going ships are very very very slow.
There is no pre-packaging of out bricks and the quality standards are not quite
as high since our bricks were never packaged. Once in a very very rare time
you would get a mixed color brick and more often you would see partial mold
bricks where there was not enough plastic to fill the mold. From the little I
understand about the consumer affairs, their brick stock has had more quality
control.
doubt my knowledge, visit my site to see me skinnyier and younger.
http://www.skypoint.com/~jkelly69/Modelwal.htm
Thanks
-john
x-lego model builder (now retired)
In lugnet.dear-lego, Gary R. Istok writes:
>
>
> Ray Sanders wrote:
>
> > Gary,
> >
> > This sounds oh-so-similar to a question I asked here...
> >
> > http://www.lugnet.com/technic/?n=686
> >
> > Ray
> >
> > Gary Istok wrote:
> > >
> > >
> > > If but it were so simple!
> > >
> > > There is one thing I don't understand about TLC. That is the "consumer • spare parts
> > > inventory" versus the "model shop inventory". I would love to know the • procedures
> > > involved for maintaining these two. Here are some questions for a TLC • person:
> > >
> > > Is the model shop inventory tracked at all?
> > > How does the two different inventories compare.
> > > And how do they get additional parts.
> > > What determines that a light blue 2x4 brick only goes to the model shop, • and not to
> > > the consumer spare parts inventory (since no known LEGO set has this • piece)?
> > > How will LEGO Direct Bulk Sales inventory be obtained?
> > > How will it be maintained?
> > > Will production runs be made to satisfy bulk sales?
> > >
> > > Inquiring minds want to know!
> > >
> > > Gary Istok
> >
> > --
> > mailto:rsanders@svic.net
> > Experienced Macintosh developer seeks telecomuting position.
> > If you have such an opening, please contact me.
>
> Thanks Ray, I must have missed your reply.
> It certainly makes you wonder how they handle the two processes.
>
> Gary Istok
|
|
Message has 3 Replies:
 | | Re: Model Shop Inventories
|
| ---...--- (...) production (...) Given the above, would it not be possible for someone at the model shop to hire some kid to do special orders out of the bulk, thus to defer the cost of parts ordered by the model shop? Seems like a (please don't (...) (24 years ago, 20-Jun-99, to lugnet.dear-lego, lugnet.general)
| | | Re: Model Shop Inventories
|
| Does that mean there are still K8s of light blue bricks and plates laying around there that we might talk them out of? ;-) I say that because there are all SORTS of pieces at LLC in light blue that never came in a production set, and aren't used in (...) (24 years ago, 18-Feb-00, to lugnet.dear-lego, lugnet.general)
|
Message is in Reply To:
54 Messages in This Thread:
 
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
