 | | RE: Mindstorms in 1999
|
|
(...) touch sensors, a light sensor, and another 700+ bricks by just buying the Mindstorms set? Just the motors and sensors alone would cost you the $80 from Pitsco. Its like getting 700 pieces for free. alex -- Did you check the web site first?: (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Borland C++ Builder 3
|
|
I have been trying to install the Spirit OCX on Borland C++ Builder 3 with no success. Does anybody knows how to do this? Thanks Pedro Jorge (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Mindstorms in 1999
|
|
I would be very surprised if the RCX itself was discontinued. Lego can continue to make easy money on that as long as there is demand through Pitsco Dacta sales (at $90? or $120?). In the educational market there is an installed base they can (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Ultimate Project
|
|
(...) I alredy had thought on this as the ultimate project for my CyberMaster (because the strong radio link to the PC). I would put the "brain" in the PC and make the unit wander in the house as if it was an extension to the brain (like the muscles (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: rotation sensors and input limitations
|
|
(...) You've come up with an admirable solution to the problem! Here's another idea, one that works on a general class of problems and doesn't require any sensor input for controlling motor positioning: The general problem class is one where you're (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | MindStorms (My Commands)
|
|
Where are the "My Commands" stored in the MinsStorms "Library"? I would like to back up the file. -- Bob Fay The Shop (URL) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Genetic programming (was "Re: IR camera?")
|
|
(...) Genetic programming in general often exhibits unintended results, namely: 1. Unless you're very careful, it ends up optimizing for the special cases rather than the general class of problem you want to solve. In the above example, you're (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Mindstorms in 1999
|
|
Yes, you can just buy the brick (nothing else). Pitsco part# N979709 for $120US. The specific URL is (URL) Message----- From: Luis Villa [mailto:liv@duke.edu] Sent: Friday, February 12, 1999 10:46 AM To: Rich Thompson Cc: Mark Tarrabain; (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Mindstorms in 1999
|
|
Good point. But if you have many motors, gears, parts, etc. Why pay for mindstorms? My first RCX was from the Mindstorms set, but the other ones have not been...they are from Pitsco. Rich (URL) Message----- From: alex wetmore [mailto:alex@phred.org] (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: NQC v. LegOS / size
|
|
(...) No, they are not in one object file. They are in a single source file, but if you look at the build process it defines a symbol like L_cmpsi3 and compiles/assembles it separately for each function. John A. Tamplin Traveller Information (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Mindstorms in 1999
|
|
(...) Although I know that without such a decision we would not have the RIS & CyberMaster, I'm a bit worried about LEGO thinking it can sell us software bundled with some parts and think we will give them the value they ask for it. I'm thinking in (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Mindstorms in 1999
|
|
(...) Don't sell yourself (and the rest of us) short. 1+% of a product run that large is nothing to sneeze at. Daniel "Dan'l" Miller Senior, School of Aeronautics and danielmi@ecn.purdue.edu Astronautics, Purdue, Indiana "Stadtluft macht frei." - (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Mindstorms in 1999
|
|
There are a lot of people on this list talking about why Lego isn't gearing the RCX towards adults. Why not institute a large letter campaign or email campaign to Lego requesting this? It worked for Star Trek in the 60s, why not the RCX in the 90s? (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Teacher in UK needs s'ware
|
|
Hi I wonder if anyone there can help a brand new novice- in fact I have just received 12 RCXs today. I teach at school and we are going to introduce the Lego eqpt to teach our 12-yr olds control tech. My problem is this. We received all 12 RCXs (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Mindstorms in 1999
|
|
Joao, (...) [Paul Curtis] Ahh, well. I notice that there are differences in prices everywhere. It just so happens that the post-Christmas sales in tke UK have provoked a slide in the price of some Lego sets. For those of you Lego enthusiasts in the (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Expansion sets
|
|
(...) That's it, yes :) (...) Ah-ha! (...) 2* RIS + 1 * 9725 = 2 RCX with 3 motors each, and a few extra sensors too. Jasper (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | lego-combat
|
|
is there any groups or offical rules for lego combat? build a bot, drop it in a ring with another bot, and see which one survives. is there any kind of group or anyone trying to start up an offical league? i'm in Dallas, Texas and i'm thinking of (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Mindstorms in 1999
|
|
Tim McSweeney wrote, (...) in the states? Does anyone know what "neat" Lego pieces will be in the Mars Explorer expansion? Extreme Creature comes with the fibre light system and Robosports with a motor. What about Mars Explorer? I've not been able (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: lego-combat
|
|
Dallas has one of the largest robotics clubs in the nation. They allow lego bots or any other kind of robot. The current contest doesn't include combat, but it does have some interesting challenges, including retrieving cans. (...) -- Did you check (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: rotation sensors and input limitations
|
|
(...) Another possible error is slippage of the belt (aside from when you want it to slip at end-of-travel). I haven't played with belts & pulleys much because when I did at first I found slippage to be a problem. Am I missing something or are you (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: lego-combat
|
|
(...) Jay, Check out Robot Arena, an autonomous robotic combat event using LEGO MindStorms: (URL) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | Re: rotation sensors and input limitations
|
|
(...) Well, it does have the limitation that you can't have a lot of torque on the "switcher" shaft, but for some applications that may not be a big problem. It all depends: 1. how much torque do you need to rotate the switcher shaft, and 2. how (...) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | New newsgroups lugnet.robotics.events & lugnet.robotics.events.robot-arena
|
|
[Followups set to lugnet.robotics.even...bot-arena] (...) Both of these groups have just been created. Here are their brief charters: CHARTER/PURPOSE ===...=== lugnet.robotics.events (group and hierarchy): Organized events, competitions, (...) (28 years ago, 13-Feb-99, to lugnet.announce, lugnet.robotics, lugnet.robotics.events, lugnet.robotics.events.robot-arena)
|
| |
 | | aargh!
|
|
I feel like an idiot, but I can't make a simple program using the RIS programming environment. I have a platform that should be able to detect the edge of a surface it's running on, but I can't build the program to drive it. Now I have first-hand (...) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | Re: new mind storm camera
|
|
(...) Check these cameras out: (URL) you check the web site first?: (URL) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Genetic programming (was "Re: IR camera?")
|
|
Of course the chief problem with genetic algorithms is that they take a tremendous amount of time to converge on an interesting solution. Actually the problem isn't so much the time as the number trials. Consider this: You need to have enough genes (...) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Mindstorms in 1999
|
|
(...) I just picked up the extreme creatures expansion set yesterday. The fiber optics effect is cool, but you sure don't get much for $59. It looks like it costs < $10 to produce. -- Doug -- Did you check the web site first?: (URL) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | An untested idea...
|
|
Hi all! We all try to get more functions out of the CyberMaster or Mindstorms, so what about this: Back in the _very_ old days of radio controlled airplanes, You didn't have a lot of channels in the radio - just one. One solution to get more (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: new mind storm camera
|
|
In a message dated 2/12/99 11:30:12 PM Eastern Standard Time, doug@knowpeace.com writes: << >your better getting a net cam and using that because you can use >that for a lot more things than the lego one coming out. Check these cameras out: >> And (...) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Mindstorms in 1999
|
|
(...) Exactly. With over a %, we're probably the largest gathering they're gonna find anywhere outside Legoland designers that can have all they want :) Jasper (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Mindstorms in 1999
|
|
(...) Didn't it take Star Trek 30 years tho? I'd hate to have to wait another 30 years :) Jasper (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Mindstorms in 1999
|
|
(...) Yeah. If you really want that piece, get the Space Shuttle. Easily better valuie for money than an expansion pack, even if it is 3* the price :) Jasper (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | firm0309.lgo anyone please?
|
|
Thanks to all who responded so quickly to my request for help Can anyone offer further help by sending me a copy of firm0309.lgo please TIA Gareth -- Did you check the web site first?: (URL) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Mindstorms in 1999
|
|
(...) It's available near me for 60 UKP ($100) ... I'm still trying to decide whether I need it :-) Stuart -- Did you check the web site first?: (URL) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Mindstorms in 1999
|
|
Tim McSweeney wrote, (...) in the states? Does anyone know what "neat" Lego pieces will be in the Mars Explorer expansion? Extreme Creature comes with the fibre light system and Robosports with a motor. What about Mars Explorer? I've not been able (...) (28 years ago, 12-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Genetic programming (was "Re: IR camera?")
|
|
(...) I think that is worthy of a few sigfiles, don't you? Jasper (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Mindstorms in 1999
|
|
(...) Go for it, if you either want to have a _very_ cool model to display, or if you like the gearbox design - it's rather cool. Also, you ghet two motors, one oldstyle technic, one mini, and a FOS element that apparently can be used as a makeshift (...) (28 years ago, 13-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Mindstorms in 1999 + My Two Cents!
|
|
I couldn't agree more! They don't know what's going on without some kind of investigation method. If they're lazy, they look only at sales figures (Not a bad method with the RIS!) But I agree that they would be VERY interested in knowing the average (...) (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | Test Please disregard
|
|
-- Did you check the web site first?: (URL) (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Test Please disregard
|
|
Please don't send test mail to the list. Send a test message to lego-robotics-help@crynwr.com. (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | Re: IR camera?
|
|
Actually, you don't need true line of sight from the RCX to the tower. The IR light is sufficiently strong enough that reflections from walls, etc. can still control the RCX and vice versa. (Try this with the RCXCC "joystick" utility.) As for the (...) (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | legOS development release imminent / C++
|
|
Hello everyone, there'll be a new development release shortly. This will probably be less stable than 0.1.6. I've been working on and integrating contributions for many different features: - automatic generation of API documentation with doxygen - (...) (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | Re: legOS development release imminent / C++
|
|
(...) These don't look exactly the same to me, but without the definition of Sensor, its hard to say... Cheers, Ben. -- (URL) grandfather once told me that there are two kinds of people: those who work and those who take the credit. He told me to (...) (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | RE: legOS development release imminent / C++
|
|
Ben, (...) I think you'll find the destructor for Sensor effectively encapsulates ds_passive(). -- Paul. -- Did you check the web site first?: (URL) (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | Re: IR camera?
|
|
Good point, I also had the brief idea to construct something like a IR-mirror which scatters the IR but with only 2 motors the mechanics become a nightmare. I looked into the palm III and its actually more difficult than initially thought: Lego is (...) (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Robotics sub-groups
|
|
(...) Well, I want the resolution that's most beneficial to the individual projects and most enjoyable for participants. Fine resolution is good as long as it lives up to the promise of providing for more focused discussions but bad if it is so fine (...) (28 years ago, 14-Feb-99, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | RCX Assembler programing
|
|
I'm using the RCX together with the Spirit OCX and VB 5. But it seems to me as the Spirit OCX has the comfort of machine language and the flexibility of standard basic. So I would like to have a more powerful and flexible tool for the programming ( (...) (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | Re: An untested idea...
|
|
This sounds like an old Lionel(sp?) train's forward-neutral-reverse switch. Anders Isaksson wrote in message ... (...) (28 years ago, 14-Feb-99, to lugnet.robotics)
|
| |
 | | Sensors
|
|
I am gathering parts to make sensors and was wondering if anyone has a good source for small microswitches ( for tuch sensors) and also LED lights 9 to 12 volt. Thanks in Advance Jim Clark ---...--- This message was sent from Bess.Net, a filtered (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors
|
|
I found every thing I needed as far as the light sensors at Radio Shack. I don't know where you're located, but here in California, Fry's Electronics is the place to go. You can get everything you need from parts, boards, and the junk food to eat (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors
|
|
The best source I can think of is the old family VCR. It has MANY momentary switches and probably 5 or more LED's in the front panel. There are two infra-red photosensors and a two sided infra-red LED on a post in the tape drive area. Good Luck! :-> (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Robotics sub-groups
|
|
(...) I agree with your gut- go with one group at first. I suspect it will be a relatively quiet group anyway. Dave (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | Re: RCX Assembler programing
|
|
Actually, you'll need a Hitachi H8 assembler. I think there is reasonable support for Hitachi H8 in the gnu assembler. Unfortunately I can't remember if the assembler is in its own distribution package, or part of binutils. Dave (...) reply to: (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors
|
|
(...) I found a GREAT source for small switches is inside an old mouse (um, computer mouse, NOT the rodent). I took apart several different brands of mice, and while they had different ways to measure movement, they all used the same type of (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: RCX Assembler programing
|
|
=>From: dbaum@spambgoneenteract.com (Dave Baum) =>... =>Actually, you'll need a Hitachi H8 assembler. I think there is reasonable =>support for Hitachi H8 in the gnu assembler. Unfortunately I can't =>remember if the assembler is in its own (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Test Please disregard
|
|
Russell Nelson wrote in message <19990214033619.2640...wr.com>... (...) it's a little late to ask them that.... m. (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: RCX Assembler programing
|
|
Hi Stefan, the h8 toolsuite will suit you fine, the GNU assembler has good support for the h8. You can use legOS without any problem at all - just provide something called "main", and you're all set. Ciao, Markus. (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | LEGO UK supplementary catalogue
|
|
I've put scans from the LEGO UK supplementary catalogue at: (URL) address for ordering your own copy is also there. It may take until tomorrow for the page to be visible outside the Demon domain. If there is sufficiant demand I could put the (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Robotics sub-groups
|
|
(...) As the creator? of HFORTH, I would LOVE to have a gruop focused on it. As it stands I am up to my eyeballs in paying consulting work and my family, and barely have enough time to keep development going. Markus has done a great job on LegOS and (...) (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | Re: LEGO UK supplementary catalogue
|
|
In article <199902151348.IAA206...gnet.com>, lego-robotics@crynwr.com had their 2d worth... (...) Er, Mozza, old bean, either these images were scanned at 10dpi or they are a bit broken. Regards, Dave Ryder. (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: LEGO UK supplementary catalogue
|
|
(...) Doh! (The one time I relied on local testing only)... Looks like I went a bit daft and forgot to put ftp into binary mode after uploading the html files. All fixed now. Thanks. -- Mozza maurice@mozza.demon.co.uk (URL) Spam! Join CAUCE! == (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: LEGO UK supplementary catalogue
|
|
(...) That would be nice... :-) Laurentino Martins [mailto:lau@mail.telepac.pt] [(URL) you check the web site first?: (URL) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: LEGO UK supplementary catalogue
|
|
In article <199902151508.KAA267...gnet.com>, lego-robotics@crynwr.com had their 2d worth... (...) Yeah, that's great thanks. - Very useful as I haven't bought any 1999 sets yet, and don't have any immediate plans to either, Not much good Technic (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors via VCR
|
|
Don't forget the motor from the VCR. I'm using my old VCR's motor to power the grabber-claw of my robot. (...) -- Did you check the web site first?: (URL) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: IR camera?
|
|
(...) True. However, in your case, you'd have evolved altruism. Still, the point was that 'purpose' is a perception overlaid on the system by humans. (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Micromotors
|
|
Micromotors. I don't have any of them, but they're available in the slim European Lego Service catalog. Are they useful for robotics? Mario (URL) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | datalog in legOS
|
|
I'm sure this has been discussed before, but I can't seem to find it in the archives- how can I write to the datalog in legOS? Thanks in advance. Luis ###...### "They call the faithful to their knees to hear the softly spoken magic spell:" "There's (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: LEGO UK supplementary catalogue
|
|
(...) I don't know if it's available in the US (probably is), my international catalogue is at home. The 'tank' is a cannon from the Competition sets - the plunger things gets pushed into the barrel and is fired by pulling the lever on top backwards (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Robotics sub-groups
|
|
(...) Ralph, which makes the most sense for the group name? Ending it in .h8hforth or .hforth or .forth? How narrow or wide of a scope is most suitable to the project? I gather from your source that the "h8" component is derived directly from (...) (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | Re: LEGO UK supplementary catalogue
|
|
In article <F77Dzy.11C@lugnet.com>, Dave Ryder <daver@ansuz.demon.co.uk> writes (...) Erm - as html interpreters ignore CR and LF, you can leave it in binary all the time. (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Robotics sub-groups
|
|
This is just my opinion, but I don't think that the creation of separate groups for legos or h8forth would be a good idea right now. Although a dedicated group to discuss alternative firmware is a good idea, I think overspecializing it right now (...) (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | Re: Mindstorms in 1999
|
|
(...) The trekkers were ground-breaking. Steve (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Robotics sub-groups
|
|
I also think that RcxCC can perfectly live in the nqc group. One suggestion: it might be good to have a more general announcement group such that e.g. new releases of RcxCC can also be announced to people that are not yet using nqc. Something like (...) (28 years ago, 15-Feb-99, to lugnet.admin.general, lugnet.robotics)
|
| |
 | | Re: LEGO UK supplementary catalogue
|
|
(...) SNIP (...) I found the tank to an old super-soaker squirt gun works ok, there are hose connections on the 'cap' to the bottle and once you split the casing it seperates out nicely. -- Did you check the web site first?: (URL) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Micromotors
|
|
I use micromotors when weight is a real factor. They are very slow and quite noisey. Also are not real powerful. But when space is short, they will do the job. Bob Fay rfay@we.mediaone.net The Shop (URL) Ferrari wrote in message ... (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | Bot Kit
|
|
Hi I am using the Bot Kit interface to program my RCX's Excellent piece of software but.......a funny thing happens when I go to the test panel to read sensor values. The first few times all is OK - sensible answers but then the values appear to (...) (28 years ago, 15-Feb-99, to lugnet.robotics)
|
| |
 | | More Outputs for the RCX
|
|
Hi All - I've been thinking of possibilities for more outputs on the RCX. This may have been covered already, but how about a few miniature relays driven by one output which would then switch power between the other 2 outputs and 4 different motors. (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: IR camera?
|
|
(...) Aren't the religious discussions on this list supposed to be confined to the ten commandments of LEGO? -- Did you check the web site first?: (URL) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors
|
|
(...) I ordered a "sensor & motor" pack from Gleason Research, and it came with 4 touch switches. Two of these were simply keys from a computer keyboard. Looks like they will work just fine. So old computers may be a source for a large number of (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: datalog in legOS
|
|
There is no datalog in LegOS. Remember it does not use the lego firmware. It's a replacement of the firmware. Instead you have the full 32KB for whatever purpose you could imagine. Use it as a big array to store your data and send it with the (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors
|
|
(...) Beware. Little to no keybards actually include separate switches. Most keyboards available today use two sheets of plastic with electrical pathways on them, whioch are connected beneath the keys when pressed. Older ones often have a PCB with (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Micromotors
|
|
Thanks Bob. I'll get my hands on. Mario (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors
|
|
(...) Old PCs with very klicky keyboards generally used ALPS-brand key switches. IBM keyboards are the classic brand here, but I've had NEC keyboards of the same design, and the old Northgate Omnikeys also used ALPS switches. You are correct though, (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: datalog in legOS
|
|
(...) Of course. (...) dir_write- THAT's what I was looking for. Thanks... Luis -- Did you check the web site first?: (URL) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Robotics sub-groups
|
|
Hi Todd, I've received several requests to set up a dedicated legOS mailing list. A while ago, you suggested setting up a subgroup, and I'd like to take you up on your offer. Could you create something on the lines of lugnet.robotics.legOS? Thanks, (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Recommended Add-On Sets?
|
|
I know this has been posted before but, can anyone suggest some add-on kits, spares, technic kits to enhance the basic Midstorms starter kit? Sources and phone numbers would be a great help. I've got the Dacta catalog if you need to reference (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) I'm in the process of writing a web page on that very subject - it'll probably still be a couple of days away, but should at least be a starting point. Stuart -- Did you check the web site first?: (URL) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Recommended Add-On Sets?
|
|
# I know this has been posted before but, can anyone suggest # some add-on # kits, spares, technic kits to enhance the basic Midstorms starter kit? # # # Sources and phone numbers would be a great help. I've got the Dacta # catalog if you need to (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors
|
|
(...) Jasper - for newer keyboards this is true - but your probably showing your age here :) Most of the early keyboards were discrete switches (Apple, Dec, IBM) It was after a while that the 'film' switches became available. I've had 1,000s of the (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) You can try: (URL) for a UK version of the supplementary catalogue. I do have an international version too, but it doesn't cover USA. Personally, I would recommend some pneumatics and some of the cannons from the competition sets (for fun). -- (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) I purchased the RIS and the Robosports expansion kit, and then ordered the following to fill it out: Lego Dacta 800/362-4308 ===...=== 2x N979891 9V Angle Sensor 2x N779945 Differentials 2x N779932 Black Plates 2x N779876 Large Turntables 2x (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | preliminary legOS API documentation
|
|
Hello, legOS API documentation is in the works. The documentation generator I intend to use, doxygen, supports HTML, LaTeX and manpage generation from javadoc and QT style comments. I've made a preliminary version of the resulting documentation (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: More Outputs for the RCX
|
|
Hi John, I have a mecanical version of this on my website, with pictures. CU Bert Visit my site on Lego, Robot's and Visual Basic at (URL) bericht----- Van: John Brubaker <photoman@novagate.com> Aan: lego-robotics@crynwr.com (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
(...) Hmm, just been thinking about this. You could have a shaft that was free to move back and forth along it axis. On the end of this you would have a series of N spokes. Each spoke ends with a free to move wheel (the axis of the wheel is arranged (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: More Outputs for the RCX
|
|
Bert - Yes, this is what I had in mind, only I would like to implement an electronic version using small relays. Thanks for the the excellent tips and resources on your Web site! I looked at your Visual Basic information when I was getting started (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sensors
|
|
(...) Possibly, but I know about that. I was referring mainly to the types of keyboard commonly seen in dump/second-hand shops today. Because, face it, if you have them already, you know about it, and if you don't have them, that's where you'd go to (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) If you don't have at least 50 #16 beams, you're gonna wish you had more... the lately demised XXL building set is a good deal, especially on clearance. Plenty of beams. Not so much gears, but a lot of long beams, and a huge amount of really (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
I get my spares from Lego in UK - there is no postage chards to Ireland. I also but dacta/mindsorms (sensors, etc.) from the Commotion Group in the UK. They ahave been excellent suppliers - you can order by CC or they will send you a proform invoice (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) The 779928/779927 Beams packages from Lego Dacta come with 4 each of the #16, #12, #10, #8, and #6 beams as well as 8x #4 and 16x #2 beams. At least in what I have done so far, I wind up needing as many of the #12 beams as I do the #16 beams. (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Recommended Add-On Sets?
|
|
(...) Anybody in the know of U.S. sources for the cannons (either in sets or sold separately as in the supplementary catalog listed above)? -- Did you check the web site first?: (URL) (28 years ago, 17-Feb-99, to lugnet.robotics)
|