 | | Re: MindStorms at Robot Store (Hacking Lego Compatible Parts)
|
|
Brett, We do a lot with robotics at the elementary and jr. high level.Having kids build their own sensors adds a lot to the experience - their labor is free. Please keep us on your e-mail list. Thanks, Tom (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | moving in a straight line with two motors?
|
|
Hi, One of the first things I ran into when making a mobile 'bot using one motor for each of two drive wheels was the mismatch in their speed. Needless to say, it's a nice way to make curved path. Not what I want. So I've got one of those nifty (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | The winner of mux startup contest
|
|
The winner for now is Paul Haas. He suggested using a channel that had an impossible value. So I scaled three of the channels for about 0 to 91 and forced one channel to be 100 all the time. The fix and better explaination are on the page now: (URL) (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | (no subject)
|
|
Hi all, Ok now i know how to charge my NiCad batteries i have laying around. Thanks to Brett and Scott for the info. I have been doing my sums to try and work out the series resistor i need to charge a 2Amp NiCad at C/10, but my figures dont seem (...) (28 years ago, 13-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | encoder
|
|
hi, I need to know what is really the 'processing time' that used in encoder especially used when a pulse is actually being recorded. I load the file "encoder.lis" into the standard lib file. I'm using a optical encoder which is a slotted wheel. (...) (28 years ago, 13-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
G'Day My 3 cents (Canadian, Eh). The most elegant solution I have seen to this problem I believe came from an old Milton Bradly 'Big Trak', in which the designers used a magnetic clutch. The idea is simple , getting the forces involved to balance (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
Ah-Oh... Magnets in close proximity to the RCX brick may not be a wise idea. On just about all of my mobile bots, the motors are immediately adjacent to the RCX brick. Just my 2 cents (US, of course!) Carl -----Original Message----- From: Giesen, (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
Giesen, Oliver writes: > Basically you get two large pulleys (or bars) and mount two magnets opposite > each other on the same side, one pulley has the two north poles facing out > and one has the two south poles facing out, when the two pulleys are (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
I might be able to use this solution for another problem. My wheeled bots have a strong tendency to go in whichever direction is necessary to run into sleeping cats. Straight line, pull to right, pull to left -- as long as there's a sleeping cat in (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
Carl G. Schaefer, Jr. writes: > Ah-Oh... > > Magnets in close proximity to the RCX brick may not be a wise idea. On just > about all of my mobile bots, the motors are immediately adjacent to the RCX > brick. The RCX has no magnetism-sensitive parts, (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) <snip> (...) Hey, sounds like goal right up there with the Mindstorms commercials - shoving all the plates off the dinner table, snapping pictures of women in the shower, etc. Great to see the big problems being solved on this list....:-> (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) So _that's_ what they mean by a "pussy magnet"! (Sorry, sorry, I just couldn't resist). Cheers, Ben. (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
Uhh --- that was a stupid comment, wasn't it? How do the Lego guys guard (or shield) against the possibility of the motor magnets disrupting the electronics or memory onboard the RCX? Carl (with a very red, I-can't -believe-I'm-an-engineer, face) (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Tim, Instead of using the differential for angle sensors, why not use it to allow a single motor to drive both wheels? Then a single angle sensor coupled with a motor could drive the steering mechanism. This setup would be very similar to a radio (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) At one point, in the distant past, I saw plans for a gear box that used either 2 or 3 differentials, I do not remember which. 2 motors were used, 1 to drive both axles, one for steering. axle1 == motor1 + motor2 axle2 == motor1 - motor2 With (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Direct Motor driver
|
|
Thanks to the fine people who figured the memory mapped motor I/O address to be 0xf000 and who determined the controlling bitmaps, I wrote a native motor driver today. See (URL) missing for a V0.1 kernel release: - task switcher IRQ reassignment (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
-----Original Message----- From: Eric Brandwine [SMTP:ericb@mitre.org] Sent: Friday, November 13, 1998 8:39 AM To: John Scott Kjellman Cc: lego-robotics@crynwr.com Subject: Re: moving in a straight line with two motors? <snip> (...) I don't think it (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: your mail
|
|
(...) 3 Watts is correct. Look at the resistor on the HB charger board. It's pretty hefty too. -Scott (28 years ago, 13-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
From: John Scott Kjellman <jkjellman@ameritech.net> (...) The main downside with this approach is that you can't turn on axis (so your vehicle will no longer have a turning radius of 0). When I first got the mindstorms I thought that it would be (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | how to adapt a voltage signal?
|
|
greetings to all i dont know if it has been asked before, but im trying to use son extra ADCs on my handyboard, trouble is they have a 0 to 5V range (analogue) but im trying to adapt the signals in the ranges of 0 to 50 volts, how do i make them (...) (28 years ago, 13-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) eh> -----Original Message----- (...) eh> I don't think it works that way. Will hooking 2 motors to the same power eh> source provide twice as much power? I think the limiting factor is the eh> current from the power source, not the number of (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) There needs to be a link to this somewhere: Peter Phillips pointed out a long while back (my messages from him are dated Sep 21) that the specs to the chip are here: (...) drivers. I don't know if he told the rest of the list about this, if (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Buy online in UK
|
|
I am looking for a place to buy the Logo Robotics Construction Kit, and I have found great online stores in the US, but I believe UK will be cheaper for me being in europe. Any good, reliable, online stores to recommend? thank you, Simen Svale (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Op een zekere dag, te weten Fri, 13 Nov 1998 17:21:08 GMT, klom lego-robotics@crynwr.com (Alex Wetmore) in het toetsenbord en schreef ons: (...) But you don't have to drive two weels. When you make one wheel for steering (thus making a (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) Aha. For those that can't be bothered to look, maximum output is 600 mA. It also tells us what the bits at 0xf000 do: 10: forwards 01: backwards 11: short (i.e. brake) 00: off (i.e. freewheel) Cheers, Ben. (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) The problem with this is that you now have a car-style turning radius (determined by front wheel deflection and traction) instead of a tank-style turning radius (essentially zero). Daniel "Dan'l" Miller Senior, School of Aeronautics and (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
I believe you are thinking of Leo Dorst's adder/subtractor. I had been eyeing this myself for use with mindstorms, since it would seem to solve the "differing motor RPM phenomena" problem. (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Homebrew sensors?
|
|
I've been brainstorming for a while about what could be done with a kludge. I'm more into the whoosh-bang side of engineering than the beep-zap, so I don't know if it would work... A few years ago, Estes (the model rocket people) made a "rocket (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) kp> There needs to be a link to this somewhere: kp> Peter Phillips pointed out a long while back (my messages from him are kp> dated Sep 21) that the specs to the chip are here: (...) kp> drivers. OK, 500mA per driver. Which, if the rest of my (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) This all depends. The table you gave (presumably from the date sheet), said: (...) Now, Lego uses Off to mean Brake and Float to Off ... (...) Well, you can set the motor to "float" and you do coast. (...) Please explain why there is (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: how to adapt a voltage signal?
|
|
You could use resistors to make a 1/10 voltage divider. If you need high input impeadance, you could build an Op-Amp circuit to divide the voltage by 10. Most ADC chips have a pin that is the reference voltage for the high end of the scale--set this (...) (28 years ago, 13-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) Hm. So I just reviewed the data sheet again, and it seems that there is indeed a significant current when the motor is shorted. That sucks. -Kekoa (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
Daniel Miller wrote in message ... (...) Daniel, I could not help but notice that you are into rockets. If so, then whoosh-bang is not the way to go. I think bang-whoosh makes a much better rocket since it should have a loud ignition, then a (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | FT639 and Lynxmotion IRPD
|
|
Has anybody try to interface a FT639 to a Handy Board ? Has anybody try to interface a Lynxmotion IRPD kit to a Handy Board ? (28 years ago, 13-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Homebrew sensors?
|
|
There is a single channel sound sensor on my web page: (URL) was really designed for picking up loud noises like claps. What you want would require two mics and a circuit that would take the difference between the sound levels. Better yet it should (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | The IR beacon, was Re: Homebrew sensors?
|
|
(...) The light sensor is directional without a tunnel. I use the IR tower as a beacon. I've got a perl script that listens for RCX messages. Here's the normal sequence of events: 1. RCX sends the message 2 "Turn on your beacon, so I can find you" (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | RE: coasting moters in nqcc
|
|
Hello all, In reading about moving in a straight line tread there was an issue related to the motor being off, on, or float. If off sets into brake mode and float does really turn them off. I thought that using float for time that the motors are (...) (28 years ago, 13-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
(...) I was thinking of something that sensed amplitude, not frequency. (Like the light sensor, which sees brightness, not color.) Of course, whatever you want for yourself is best. :) I know the logic of taking two sensors and differentiating to (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
(...) Unfortunately the bang comes with the whoosh, often leading to a rapid unplanned dissasembly. Witness the recent destruction of Delta III #1, caused by a 4hz roll oscillation, or the Titan IV that ended in a BFRC due to a clog in its wacky (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | RE: Homebrew sensors?
|
|
Why would you need an array to do that? You could do it with three variables: var1 = starting angle var2 = highest amplitude encountered so far var3 = angle of highest amplitude The algorithm goes something like this (in pseudo-C): var1 = (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | MindStorms on NT / trouble posting to the list
|
|
I'm posting this question on behalf of peterbag@microsoft.com. Please direct replies to that address... Peter asks, Help! I am considering purchasing a MindStorms kit tonight, but I want to make sure it will run under WindowsNT. Has anyone done (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Alex Wetmore wrote in message <008601be0f2a$01b821...ft.com>... (...) This would give you a good turning radius. However, it would take the bot a long time to turn. (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Ardjan Besse wrote in message <364c7d42.4532817@lu...et.com>... (...) "Straight" is a relative term. For example, while the alignment might be 0straight, the wheels might not provide the bot with the ability to travel in a straight line. I believe (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) 1) You've been playing too much Carmageddon. 2) Control theory is relatively new (it paces the development of computers). There are quite a few good textbooks available, but a professor is a much greater help. Familiarity with calculus and (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Daniel Miller wrote in message ... (...) What? (...) This is all fine and well, but I was thinking about something a little less complex. The RCX doesn't have the power to perform image processing and sophisticated feedback control. What I was (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re:
|
|
Hi everyone, The mistake you make in your calculation is that in your calculation you take the entire 15V for the resistor and this leaves no voltage for charging your NiCad. Do the same thing again and deduct your NiCad voltage from the 15V you (...) (28 years ago, 14-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Cybermaster protocol?
|
|
Does anybody have information on the basic Cybermaster packet protocol handy? How does it differ from the 55 ff 00 D ~D D ~D C ~C format of the RCX? -Kekoa (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) Believe it or not, I've been working on exactly this problem for the last few days. I built an angle sensor using a 500K potentiometer wired directly to an RCX input port. (Lego's angle sensor doesn't have sufficient angular resolution unless (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
(...) So's Michael - he's proposing a notch filter so you get the amplitude at a particular frequency, which may be better for a seeking application. Cheers, Ben. (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) I think making the pendulum longer should cure this... (...) Possibly making it heavier will cure this... Cheers, Ben. (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
In article <Pine.GSO.3.96.98111...129.6050E- 100000@expert.cc.purdue.edu>, Daniel Miller <danielmi@expert.cc.purdue.e du> writes (...) Ah. A jet engine expert. It always puzzled me how the hot air knows it is supposed to go out of the hole at the (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Homebrew sensors?
|
|
does pressure difference make any sense?..:-) Selçuk (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: NiCd Charger
|
|
Russ: In a message dated 98-11-13 04:48:38 EST, you write: << ... power rating of resistor = 15Volts * 200mA = 3Watts Series resistor needed = 75 Ohms @ 3 Watts. ---...--- ------- The 75 Ohms bit seems reasonable to me but 3Watts must be way to (...) (28 years ago, 14-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
---...--- (...) attached. (...) is (...) is (...) sheet (...) I expect that the "motor is shorted" state is achieved by turning on either both high-side drive FET's or both low-side drive FET's, and niether of these combinations would provide a high (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Cybermaster protocol?
|
|
(...) If I'm not mistaken, Peter Ljungstrand has compiled this information at (URL) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Mindstorms meeting in Boston
|
|
Hey -- any Boston area people should come to the Construction Site tomorrow (Nov 15) from 7-9 for a Mindstorms show-n-tell/get-together. Details (such as there are) on lugnet in lugnet.loc.us.ma.bos (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | How to receive messages from the CuberMaster unit?
|
|
I'm currently using Dave Baum's NQC on a Linux system with CyberMaster (thanks to Peter Ljungstrand's adaption), and am very happy with that. However, I often find myself in the position where I want to transfer data from the CyberMaster mobile unit (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) Image processing? Proportional control pushes back proportional to deflection (i.e. it simulates a spring). Derivative control pushes back proportional to rate of deflection (i.e. it simulates dynamic friction). Integral control pushes back (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
(...) Perhaps you're asking too much of them. Try toning down the pendulum; that is, give it some length below the hinge point as well. As long as it's still top-heavy you're still technically an inverted pendulum, and the added mass below the pivot (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Monitoring household power consumption
|
|
Hi all, I found an interesting article by Don Lancaster in May 1998 issue of the magazine, Electronics Now. Maxim makes a chip (MAX125) that will convert accurately four channels of analog data to 13 bits accuracy, plus talk about a device for $79 (...) (28 years ago, 14-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Alex Wetmore wrote in message (...) If you are thinking pneumatics and mindstorms, you might check out an electric pneumatic switch (made in Lego) at (URL) it is interesting to note that the piston of a fully charged and extended cylinder will (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
-- ===...=== Don Forth ( Klaatu ) email: dforth@caro.net Home Page: (URL) Brandwine wrote in message ... (...) Check out - (URL) has an example of a treaded vehicle that uses this type of system one motor for forward and backward motion and one for (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | RE: moving in a straight line with two motors?
|
|
Carl G. Schaefer, Jr. <lego-robotics@crynwr.com> wrote (...) By making sure the magnets are not strong enough to do those things. Which isn't hard - it takes a very strong magnet to interfere with solid state electronics. It's only magnetic media (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Request for Books on Robotics
|
|
Could people please recomend some books about lego robots, using the handyboard or other controllers, or more general textbooks on the topic of educational robots? Thank you, Rachel Arens (28 years ago, 14-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
Tim, I used a quick and dirty technique to create steering maps for a robotic car when I was an undergrad at RPI and it sounds like you've got all the ingredients you'd need to do the same thing. Essentially you need to tow a trailer behind your (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Online ordering available
|
|
(...) The discount is the time you have to wait........ Is it not scarce? Do they not have them in stock? Soooooo, they discount the waiting period......... Sorry, I am just being silly..... (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: MindStorms on NT / trouble posting to the list
|
|
I've been running the MindStorms software under NT, and I haven't had any trouble at all. I don't think that NT is formally supported by LEGO, but its been just fine for me! -----Original Message----- From: Eric Eilebrecht <ericeil@microsoft.com> (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | Re: MindStorms on NT
|
|
(...) I'm not using the LEGO software anymore since I discovered nqc, but I remember it was very slow on a P120, taking 100% CPU all the time. Typing (sleep-times, filenames...) also didn't work the way it should, it was very slow and didn't display (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | RE: MindStorms on NT / trouble posting to the list
|
|
I have been using NT with mindstorms for two weeks now, and I have yet to find a problem with it. bradley green (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | No discount? (was Re: Online ordering available
|
|
(...) Well, it may or may not be scarce. I have in the last two days been to the Learningsmith in Cherry Creek Mall, Denver CO, and the Learningsmith in Woodland Mall, Kentwood/GR, MI, and both of these fine establishments have at least 3 of the (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | Spirit.OCX & Starting a Program
|
|
If I want to start a program using spirt.ocx do I use StartTask (number) ? I've been trying to use this with no luck. And would appreciate some help with this. (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Spirit.OCX & Starting a Program
|
|
I don't use spirit.ocx - I work directly with the bytecodes, but I think this info is true for spirit.ocx as well... The number in StartTask(number) refers to a task within a program (each program can have multiple tasks). Typically, you would use (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | Real-time communication or just download programs?
|
|
Hi, I am thinking about buying the Mindstorms kit, but I was wondering if you can just download programs to execute in the brick, or if you can control it at runtime from the computer? I am interested in using it with things like genetic algorithms, (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Spirit.OCX & Starting a Program
|
|
If you use the .BeginOfTask Method and pass in the number 0 you will start the program the same way as if you started a program with the Run button on the RCX. ---...--- (...) ? (...) help with this. (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Real-time communication or just download programs?
|
|
If you use the Spirit OCX you can do either autonomous programs or ones that interact with your pc. ---...--- (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
so do you still have a big track ? Mine is unfortunately missing a wheel : ( Jason@Inphotek.com Giesen, Oliver <lego-robotics@crynwr.com> wrote in article <E10BAC791F2ED2119D9...th.com>... (...) (28 years ago, 14-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Real-time communication or just download programs?
|
|
In message <364F3A6C.783218B6@erols.com>, Garrett Snider <gsnider@erols.com> writes (...) Both - and both together I think! I have been experimenting with my recently acquired CyberMaster which is similar to the Mindstorms only it can support less (...) (28 years ago, 15-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Spirit.OCX & Starting a Program
|
|
(...) Is it possible to do this from within a running program? What I read implied to me that the SelectProgram() would stop the current program so it wouldn't be running to issue the StartTask(). It would sure be nice to have a movement program (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Spirit.OCX & Starting a Program
|
|
(...) As far as I know, you can't set and start a different program from within another program. Execution stops when you switch programs, so the following start task instruction will never get reached. Maybe Dave meant that you can switch programs (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re : Moving in a straight line
|
|
Hi All I have read with some amusement all the traffic on this subject. I have a home brew lego robot with two shaft encoders - by comapring the counts of "clicks" or rotations just speed up or slow down one set of wheels. Depending how straight you (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Broken Board (SPI??)
|
|
Hi, I'm using the Polaroid 6500 ranging board with the sonar routines on the HB web site. When I call the sonar on one HB it returns -1 but when I try it on another HB it works fine. So it isn't the sensor. Could anyone tell me which conections on (...) (28 years ago, 16-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | (no subject)
|
|
Hi! all, I charged my handyboard for two days. Any problem iam going to get. Please respond me quickly as i had to do my project. thank u. Madhu (28 years ago, 16-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Spirit.OCX & Starting a Program
|
|
(...) Yep, that's exactly what I meant. Dave (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | How to download firmware file (non-Windows approach?)
|
|
Is there any way to download the firmware without using the Windows RCX software? If so, please provide instructions. Why? I would like to get away from using a windows machine ASAP. It looks like there are plenty of development tools etc. But I (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re: How to download firmware file (non-Windows approach?)
|
|
I asked the wrong question earlier. I *do* want to use a windows machine. I *do not* want to use the Legos RCX windows software. So, is there any windows shareware that will allow me to download the firmware file? Thanks, billq (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | use robot invention system without cd in drive ?
|
|
hi all, as a beginner, i find it _VERY_ annoying that it is not possible to copy the software from cd to disk and to install and run it from there. anyone knows a way how to load the entire cd to disk and to install and run from there (i got plenty (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | CM package
|
|
In a previous post I wrote that Cybermaster comes in a cardbox box instead of the alu/plastic case depicted in the catalog. This was based on observations in the Netherlands. This weekend however, I noticed that the set *does* come in an aluminium (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re: moving in a straight line with two motors?
|
|
What about a gyrocompass in a mobile robot? May work for orientation but eats batteries. Eric Brok Visit LEGO ON MY MIND: (URL) Control section: (URL) section: (URL) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re: How to download firmware file (non-Windows approach?)
|
|
lego-robotics@crynwr.com wrote in message <852566BE.002B8A23.0...am.com>... (...) It's a feature of Mind Control. Copy the firmware file on your cd-rom into the Mind Control directory before doing this. LEGO on my mind Mindstorms/Mind Control (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | RE: WindowsNT
|
|
Hi (...) sure it will run under WindowsNT. (...) There is one bug in the RCX programming graphical interface : you cannot enter names for saving programs or naming custom commands (a small keybaord problem I guess). But it's very boring since you (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | motor port problem
|
|
hi, i really need help urgently. Currently, I running my robot using 2 DC motor on port 2 & 3. I used external power supply to the L293D (pin 8). I did not cut the trace. I used Alkaline battery 12V recharagable . when I run my robot, it is running (...) (28 years ago, 16-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | correct procedure when downloading pcode_hb.s19
|
|
hi I am at present building a handyboard from Fred's assembly manual, however it appears I might have a problem. I have connected the serial interface board to the handyboard. The hb is placed into bootstrap mode by holding down the stop button. The (...) (28 years ago, 16-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: MindStorms on NT
|
|
(...) I've been using Lego Robotics since it's release date (oct. 3 I think) with NT and have had no problems yet. -Ang (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re: The IR beacon, was Re: Homebrew sensors?
|
|
(...) And if you mounted some sort of plug on the front of your robot it could mate with a matching socket when it entered the garage and wait there until its batteries were recharged! (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Spirit.OCX & Starting a Program
|
|
(...) Doesn't the mysterious opcode d2 allow you to do that? Or am I missing something? }}Date: Sun, 25 Oct 1998 15:35:08 -0800 (PST) }}From: Kekoa Proudfoot <kekoa@Graphics.Stanford.EDU> }}To: Lego Robotics <lego-robotics@crynwr.com> }}Subject: Re: (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re: CM package
|
|
Neither in Portugal. Our comes with a cardbox box also :-( Laurentino Martins (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | RE: WindowsNT
|
|
(...) Actually sometimes it does work, but you can't see what you are typing, only after you press enter or <ok> you can see what you typed. (...) You can't do that using the LEGO software anyway. nqc on the other hand works great with NT. Erik. (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re: Request for Books on Robotics
|
|
Mobile Robots: From Inspiration to Implementation by Joseph L. Jones, Anita M. Flynn; As its title suggests, this book convers everything you need to know to build a mobile robot. They discuss the design of their brain (a MC68HC11 design that looks (...) (28 years ago, 16-Nov-98, to lugnet.robotics.handyboard)
|
| |
 | | RCX software / design sharing
|
|
Time for a question that has probably already been answered (just not all at once ;-) I have been playing with my Mindstorms for about a week now and am growing impatient with the RCX software that ships with the unit. I know there are many things (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|
| |
 | | Re: The IR beacon, was Re: Homebrew sensors?
|
|
(...) ph> I think that the light sensor is read once every 3 milliseconds. When you ph> think you're reading the light sensor, you're really getting the last ph> sample. Anyone want to verify that? Dunno about the bit level, but the Official Lego (...) (28 years ago, 16-Nov-98, to lugnet.robotics)
|