To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 2259
2258  |  2260
Subject: 
The Handyboard (was Re: RCX 2.0 -- ideas.)
Newsgroups: 
lugnet.robotics
Date: 
Mon, 4 Jan 1999 18:13:03 GMT
Viewed: 
1441 times
  
Rob Visscher wrote:

Multiple ports are  possible if you buy or build a Handyboard. Check out this
URL.
http://lcs.www.media.mit.edu/groups/el/projects/handy-board/

The Handyboard is, indeed, a very cool way to control robots.  Personally, I am
more than a little impressed by it.  Why didn't LEGO base their RCX unit on it?
Or why not the MIT Programmable Brick?  (It at least had more I/O ports than the
RCX does)  The 6811 microcontroller is, from what I remember from electronics
class, an awesome unit to work with.  It even has a good share of software
development tools available for it.  Ah well... I guess that's water under the
bridge now, as it were.

My *only* beef about the Handyboard is that Fred Martin does not explain how to
convert the bare motherboard into a more LEGO modular unit (with LEGO electric
connectors, and being encased in a "LEGO brick" of sorts).  The Handyboard just
does not lend itself superbly well to incorporation with LEGO's modular bricks
without making substantial cosmetic modifications, the full nature of which may
not be entirely obvious to people who merely purchase a ready-made Handyboard
rather than buying the build-it-yourself kit.  Isn't the point of LEGO to be able
to build, dismantle, and reassemble in whatever way the imagination can dream
up?  I'm not suggesting that the Handyboard be reduced to a LEGO-only device, but
rather that there should be some relatively easy to understand instructions in
how to adapt the board for that kind of use.  There are probably many ways it
could be done, of course, but it'd sure be nice to have specific instructions on
how to do it at least one way.  If there were, I'd almost certainly be snatching
one up right after my next paycheck.

Mark



Message has 2 Replies:
  Re: The Handyboard (was Re: RCX 2.0 -- ideas.)
 
There are two very easy methods of making LEGO compatible 9V connectors. 1. Use Dacta #779897 9V Connecting Leads (3 pieces) @ $12.25. Cut the leads to the appropriate length for your use. Break a male 0.100" strip header (DigiKey #929834-01-36-ND) (...) (25 years ago, 4-Jan-99, to lugnet.robotics)
  Re: The Handyboard (was Re: RCX 2.0 -- ideas.)
 
(...) How about using a few large plates (of the type found as baseplates in small to medium sets), and a few basic bricks, possibly with the addition of glue to keep it all together? Jasper (25 years ago, 23-Jan-99, to lugnet.robotics)

Message is in Reply To:
  Re: RCX 2.0 -- ideas.
 
(...) Multiple ports are possible if you buy or build a Handyboard. Check out this URL. (URL) regards Rob Visscher (25 years ago, 2-Jan-99, to lugnet.robotics)

46 Messages in This Thread:























Entire Thread on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact

This Message and its Replies on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact
    

Custom Search

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR