To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *4101 (+100)
  Steppers
 
Hi. I was reading through a compilation of emails from the Handy Board Q&A and found a lot of great questions, but no answers to them. I am trying to power some steppers, microsteppers from the RobotStore catalog, with the HB and am not having much (...) (28 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Serial line interrupt
 
(...) to (...) about (...) Hi, you could simply build and Acknowledge routine so that every character sent by the PC could be echoed back by the HandyBoard. It asks a bit more of processing time from the HandyBoard, but at least it's simple to build (...) (28 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Steppers
 
Dear Terri, If the motors turn sparatically, that means the coils are probably not hooked up in the correct order. Try swapping them around and see if anything improves. The motors you are using are the bipolar type. There is a decent way of hooking (...) (28 years ago, 6-Jul-98, to lugnet.robotics.handyboard)
 
  help needed for ir sensors & memory addressing latch
 
Hi all, I am new to robotics and have great difficulty trying to get the near-infra emmiter and detector on the HB to work properly. After studying the schematics, I figured out to activate J7, I should do a bit_set(0x1000,0b01000000) which appears (...) (28 years ago, 7-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Serial line interrupt
 
Hello all, I have also had this problem and would be interested in any resolution. However, on another note has anyone had luck or intruction on how to you the serial code here : (URL) am not sure how this works and any information would be greatly (...) (28 years ago, 7-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Connecting radio module (BiM 418 F)
 
Hello all, I was surprised to see one of my old postings on this list appear again this week. The problem I posed here has been solved, and the results can be found via this page: (URL) Sipke van der Veen (28 years ago, 7-Jul-98, to lugnet.robotics.handyboard)
 
  RE: check_sensors.c
 
Terry, It seems that alot of the problems with this piece of code are syntax errors, you could correct alot of these by looking up the secific syntax in the HB manual and there may or may not be a few things that I would have done differently (...) (28 years ago, 7-Jul-98, to lugnet.robotics.handyboard)
 
  stepper motors: choosing an approach
 
There appears to be much interest in using the handyboard to control stepper motors. Choosing the right approach depends on what you want your robot to do. There are a number of specialized boards for controlling stepper motors, but they are (...) (28 years ago, 7-Jul-98, to lugnet.robotics.handyboard)
 
  Inclinometer for Handyboard
 
Hello, I've been searching, without much luck for a single axis inclinometer with a reasonable settle time and +-30 degree resolution, for less than $50. Anyone have any leads? Thanks, Aaron (28 years ago, 7-Jul-98, to lugnet.robotics.handyboard)
 
  Interrupt Handler for Serial communication
 
Here's a bit of code that will buffer incoming serial information so that no information will be lost when transmitting to the handy board. There are two files: serial_isr.c and serial_isr.asm. You'll need to assemble the .asm file using as11_ic, (...) (28 years ago, 7-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Inclinometer for Handyboard
 
Don't know if home brew is OK for your needs but I found a little while back, a website that had several different homebrew sensors described and a single axis inclinometer was one. try using +robot +inclinometer in the Altavista search engine. The (...) (28 years ago, 8-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Geared Motors
 
Does anyboady have experience using German Made Geared DC Motors made by : FAULHABER. 12V/ 22b40.5 Motors have been salvaged from an old 'Plasmon' Optical-disk-Jukebox I have several of these identical motors that i want to use as main traction (...) (28 years ago, 8-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Inclinometer for Handyboard
 
(...) Why not try building your own by putting a couple of mercury switches on a servo. (28 years ago, 8-Jul-98, to lugnet.robotics.handyboard)
 
  ic help
 
Can someone please shed some light on the commands "peek" and "poke" for Interactive C. For some reason I am having trouble with the syntax. Thank you (28 years ago, 8-Jul-98, to lugnet.robotics.handyboard)
 
  Re: ic help
 
the addresses must be specified in decimal. Justin D. Gullotta.. , Engineer, Rensselaer Polytechnic Institute. (28 years ago, 8-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Inclinometer for Handyboard
 
(...) (URL) has inclinometers.. dunno how much they run however. -d The box said "Requires Windows 95/NT or better"... So I got Unix. Free the Source. Free your Computer... (3 URLs) (28 years ago, 8-Jul-98, to lugnet.robotics.handyboard)
 
  RE: Inclinometer for Handyboard
 
You could use the effect of gravity force and a potentiometer (variable resistant) to create such thing. In fact if you use a joystick mechanism (or quadraphonic double-potentiometer volume control in the old day) in upside down position and have a (...) (28 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
 
  RE: Inclinometer for Handyboard
 
In the previous message, the word 2-dimensional is incorrect. It should be 2-axis (...) (28 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
 
  FW: Inclinometer for Handyboard
 
(...) (28 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
 
  Re: ic help
 
Hi LLya, Actually, descriptions of these functions are described in HB manual, at least mine has. peek() returns integer value for the given location passed in as the parameter. For example: value = peek( 0x200); The peek returns the int. value (...) (28 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Inclinometer for Handyboard
 
greetings everyone, this is a reminder to please NOT send 1MB attachments to the list! In the guidelines I sent you when you were subscribed to the list, I stated a limit of 50 KB (that's kilobytes) for any message. Please remember that your message (...) (28 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
 
  IR, bitmapping
 
I was just wondering if you could get the handyboard to transmit other than just in 125 hz or 100hz. Also...has anyone done anything like making a robot follow another using the ir transmit? Has anyone had any success using shaft encoders to make (...) (28 years ago, 9-Jul-98, to lugnet.robotics.handyboard)
 
  Re: check_sensors.c
 
Hi Joe&David,All, Let me explain what I would like my handyboard to do. Guide a lawnmower by detecting the border of cut and uncut grass. Monitor a row of 16 +or- ir emitter/detector pairs placed about every two inches to report to the motor control (...) (28 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
 
  Sorry: Re: Inclinometer for Handyboard
 
I humbly apologize for the time and bandwidth I forced on everyone with my intended-to-be-small...-and-dirty sketch on the inclinometer. I honestly did not realize the size of the file when I sent it or I'd have found a much better way of doing so. (...) (28 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
 
  External ram
 
Hello all, I have an 68hc11F1 and 32 K of external ram and 32k of flsah. I have the 16 mhz version of the hc11. While having problems to program the flash suggestions from the list where that i probably had a timing problem. So i reduced the (...) (28 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
 
  assembler
 
Hello, can anyone tel me the function of the # in the AS11 assembler, i'm new at assembler programming and get sometimes confused about the usage of the # # means a number, but what's the difference between: ldaa #$1000 and ldaa $1000 Thanks, (28 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
 
  Re: assembler
 
Hi Richard, Sorry for my bad english (normaly i speek german). The 68hc11 has differnt kinds of addressing-modes. 1) LDAA #65 : immediate adress, The value is stored in accumulator 2) LDAA result : direct Adress The value from adress RESULT is (...) (28 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
 
  Re: assembler
 
Hi all, Would be great if messages were sent in plain ASCII... Andre Ramos (28 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
 
  ASM 96
 
Hi, sorry to drift from the point of this mailing list but I have a question for all the 80C196 users out there. Does anyone have ASM 96? I have been searching for it for weeks now, without any luck. The only thing I can find about it is updates to (...) (28 years ago, 10-Jul-98, to lugnet.robotics.handyboard)
 
  Mini SSC
 
Has anyone used their handyboard to talk to Scott Edwards servo controller (the Mini SSC I or II)? I'm about to experiment with this as soon as my 12 servos arrive, and was wondering if anyone could provide any useful insights or code. (28 years ago, 12-Jul-98, to lugnet.robotics.handyboard)
 
  PLAIN TEXT ONLY
 
Dear all, I would like to remind everyone to please attempt to send PLAIN TEXT ONLY messages when you post to the Handy Board mailing list. This is to respect the many of us who have old fashioned text only mail readers, and to save bandwidth in the (...) (28 years ago, 12-Jul-98, to lugnet.robotics.handyboard)
 
  communicating with the Scott Edwards SSC's
 
Hi all, There is a 9600 baud driver for easy control of the Scott Edwards Serial Servo Controller. Please see (URL) and look for the link, "9600 baud serial output." Yours, Fred (28 years ago, 12-Jul-98, to lugnet.robotics.handyboard)
 
  Please advice on the alogorithm
 
Hello, I need some help to go on in my project. The following are the question needed to be answered : 1) Presently, I'm writing a program using Interactive C in my project. The project is involved a robot which has to be mobiled and move from one (...) (28 years ago, 13-Jul-98, to lugnet.robotics.handyboard)
 
  dvice on the algorithm
 
Hello, I need some help to go on in my project. The following are the question needed to be answered : 1) Presently, I'm writing a program using Interactive C in my project. The project is involved a robot which has to be mobiled and move from one (...) (28 years ago, 14-Jul-98, to lugnet.robotics.handyboard)
 
  Please add me to the list
 
Administrator Please add my email to the handyboard list. Thanx Hachemi (28 years ago, 15-Jul-98, to lugnet.robotics.handyboard)
 
  Sumo-Robots
 
Hi all, i´m looking for germany-sumo-robotic fans and builders. Is there any sumo-events in germany ? Have somebody infos about sumo-robots (construction, tip & tricks, etc.) ? Bye Bernd Klein P.S. I know the www-Pages from Bill Harrison, PARTS and (...) (28 years ago, 15-Jul-98, to lugnet.robotics.handyboard)
 
  Request Help on the HD
 
Hi, Currently, I using Seal Lead Acid batteries (1.2Amp hrs) of voltage 12 v to drive my Stepper Motor and photoelectric sensor. stepper motor using 3v and current is 2 Amp. Sensor is using 12v and current is 35mA max. The total sensors used are 7 (...) (28 years ago, 15-Jul-98, to lugnet.robotics.handyboard)
 
  MiniBoard Needed
 
All Anyone has a working miniboard for sale. I need it ASAP. Please Help. ---...--- Hachemi Mechlih URL : www.fanucrobotics.com FANUC Robotics North America, Inc. Email: mechlihx@frc.com 3900 W. Hamlin Road Voice: (248) 377-7755 Rochester Hills, MI (...) (28 years ago, 15-Jul-98, to lugnet.robotics.handyboard)
 
  Config register 0x3c
 
Hello all (especially Fred and other gurus), I have some config register woes I can't resolve, and the mail archives have only got me so far. I had a little electrical "accident" and now when I try to download pcode using HBDL in Win95, the boot (...) (28 years ago, 15-Jul-98, to lugnet.robotics.handyboard)
 
  request help on handyboard
 
hi, Currently, I using Seal Lead Acid batteries (1.2Amp hrs) of voltage 12 v to drive my Stepper Motor and photoelectric sensor. stepper motor using 3v and current is 2 Amp. Sensor is using 12v and current is 35mA max. The total sensors used are 7 (...) (28 years ago, 15-Jul-98, to lugnet.robotics.handyboard)
 
  Re: request help on handyboard
 
---...--- (...) <kfm@gull.me.es.osaka-u.ac.jp>; Lim Jew Huang <limjh@pacific.net.sg>; Dr david Rye <rye@mech.eng.usyd.edu.au> (...) to (...) (28 years ago, 15-Jul-98, to lugnet.robotics.handyboard)
 
  LM20X21A
 
Hello all: Does anyone know how to program a character into Sharp Dot Matrix LCD LM20X21A ? I want to add the greek character, miu ( the one that looks like italized 'u') I will be very grateful if anyone can help me out this. Cheer! Felix Adekola (28 years ago, 15-Jul-98, to lugnet.robotics.handyboard)
 
  Handyboard/RWP without p-code
 
Hi All, I would like to use the Rug Warrior board (similar configuration as the Handyboard) with conventional tools - assembler, C compiler, monitor. No Interactive C or p-code, and I am prepared to run the board in bootstral/expanded modes without (...) (28 years ago, 16-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Handyboard/RWP without p-code
 
Get a copy of icc11 v5.0 or later (from www.imagecraft.com) and use the handyboard library from their site. --Chuck (28 years ago, 16-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Handyboard/RWP without p-code
 
Hi I suggest that you contact ImageCraft. (URL) or info@imagecraft.com They have a C compiler for 68HC11 CPU's that will do what you want, including a library for the HandyBoard (see attached e-mail) ! I have no affiliation with ImageCraft (other (...) (28 years ago, 16-Jul-98, to lugnet.robotics.handyboard)
 
  SPI problems
 
I am trying to connect my Handyboard with a Motorola 68HC11A1FN chip inside with a AD7858L- 12-bit ADC. In my IC code I first write to the DDRD (Port D Data Direction Register) ($1009) and activate SCK(bit4), MOSI(bit3), MISO(bit2). Then I write to (...) (28 years ago, 16-Jul-98, to lugnet.robotics.handyboard)
 
  Simultaneous Control of Multiple Servos
 
I have asked this before and not received much regarding this question. So, here goes again. In building a walking robot, how important is it to control the motion of all legs simultaneously? Seems like that pulsing one at a time creates the (...) (28 years ago, 17-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Simultaneous Control of Multiple Servos
 
You are correct to assume that all legs should be in sync with each other and that all the legs on the ground should be moving at the same rate in the same direction to move straight (sometimes you don't want to move straight!). BUT now think of the (...) (28 years ago, 17-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Simultaneous Control of Multiple Servos
 
I would suggest that just getting a walking robot to walk with coodination and then being able to turn in place and in an arc will be challenging enough to begin with. Just adding enough intelligence to adapt to rough terrain and the change gaits (...) (28 years ago, 17-Jul-98, to lugnet.robotics.handyboard)
 
  RE: Simultaneous Control of Multiple Servos
 
I have included site addresses that I have found useful. (URL) Maker of the Hexapod robot using a buffer of sorts (D-type latches) for simultaneous control. Definitely worth a look, he's put a lot of information into this site. (URL) Creator of (...) (28 years ago, 17-Jul-98, to lugnet.robotics.handyboard)
 
  Gleason Reserch
 
Do you know what is going on with Gleason Research ??. Thay are not responding the e-mail !! Ricardo Barrenechea rbarre@cis.com.ar (28 years ago, 17-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Simultaneous Control of Multiple Servos
 
That's the way I thought it had to be done. What I was considering was routines that moved each leg the same short distance (for straight line walking). Walking would consist of very short increments of movement. Now, this seems like it would move (...) (28 years ago, 17-Jul-98, to lugnet.robotics.handyboard)
 
  Config register 0x3c
 
As no one has any insight into why I'm getting a config register value of 0x3c when downloading pcode, I am into speculation mode. To refresh people's memory: All of DL, DLM, and HBDL refuse to download the pcode to my chip, and HBDL reports that my (...) (28 years ago, 17-Jul-98, to lugnet.robotics.handyboard)
 
  Handy Board Keeps crashing
 
I keep getting errors that there is extra bytes on the stack. I reset the board a couple of times and that does not help. I appreciate any help. Faris (28 years ago, 17-Jul-98, to lugnet.robotics.handyboard)
 
  HB Stress Ability
 
Hello! Does anyone know how much stress can be put on a HB?? I'm into rocketry and thought about putting it in my rocket that I'm building. I was wondering: Will it work while flying in the air with the increaced G-force and high speeds? Thanks! (...) (28 years ago, 17-Jul-98, to lugnet.robotics.handyboard)
 
  Re: LM20X21A
 
(...) Erm... I am just guessing here, but, I don't think it would be unreasonable to suspect that this particular LCD uses the Hitachi LCD chipset that just about every LCD manufacturer utilizes.. and every LCD chip fab'r emulates. HM44780 is it? (...) (28 years ago, 18-Jul-98, to lugnet.robotics.handyboard)
 
  I'm Sorry!
 
Sorry that my last message was sent in HTML format. Hopefully, it will not happen again Phil Hahn (28 years ago, 18-Jul-98, to lugnet.robotics.handyboard)
 
  beta testers wanted for LEGO MindStorms
 
Hi all, LEGO is officially looking for beta testers for their new MindStorms product scheduled to ship this fall. I'm not sure what their selection criteria are, other than that you must live in the States and have Pentium running Windows 95. It's a (...) (28 years ago, 18-Jul-98, to lugnet.robotics.handyboard)
 
  RE: SPI problems
 
Serial libraries are wwriten for Serial port,not for SPI port! Are you needing use the spi like a standard oitput port or like a SPI (synchronus serial port)???? Is the device spi compatiible? If yes, you need the portd to work like a SPI port. if (...) (28 years ago, 19-Jul-98, to lugnet.robotics.handyboard)
 
  Parellel port control
 
Has anybody tried using the "delay function, outportb function and inportb function" that comes with Borland C++ 5.01. I am trying to control a set of LEDs conncted to my printer port using a C++ program. My program woudn't compile. The error is (...) (28 years ago, 19-Jul-98, to lugnet.robotics.handyboard)
 
  (Fwd) Extra HB For Sale
 
Oops! I had my date set incorrect, on my PC. This was sent out on July 19th not June 10th. ------- Forwarded Message Follows ------- From: "Mike Davis" <ipscone@halcyon.com> To: handyboard@media.mit.edu Date sent: Wed, 10 Jun 1998 08:41:19 -0700 (...) (28 years ago, 19-Jul-98, to lugnet.robotics.handyboard)
 
  Comm problems
 
Hi all, I am currently having problems getting my HB to talk with my computer. I am using IC 3.2. Because of time and work pressures I have not been able to play witht my bot for a couple of months. Everything worked fine then. I didn't change (...) (28 years ago, 20-Jul-98, to lugnet.robotics.handyboard)
 
  Another HandyBoard for sale
 
Hi all, I also have a Handyboard for sale, but with a 20x4 display and the IR demodulator. No casing, however. Price is just slightly more at $235, includes shipping. It has a A0 processor. I'm selling it because it's a bit "overpowered" for my (...) (28 years ago, 20-Jul-98, to lugnet.robotics.handyboard)
 
  Need Help to solve the algorithm.
 
Hello, I really need help to solve the alogrithm in using the HD with interactive C program . Presently. I'm constructing a mobile robot to move within a battle field of 5metres by 5metres. In side the battle filed, the "mines" are visible with (...) (28 years ago, 20-Jul-98, to lugnet.robotics.handyboard)
 
  re: paralell port
 
Somebody request some info about paralllel port look in thisd site for an example writing in C (URL) (28 years ago, 20-Jul-98, to lugnet.robotics.handyboard)
 
  Sonar Help!
 
Hi, I am having problems getting my Polaroid sonar to work properly. Following Kent Farnsworth's directions, I have hooked up the sonar: Sonar ====> Handy Board ECHO TIC3 (Top position) V+ TIC3 (Middle) GND TIC3 (Bottom) INIT PIN 9 of 2nd L293DNE (...) (28 years ago, 20-Jul-98, to lugnet.robotics.handyboard)
 
  LCD routines
 
I would like to be able to use the LCD screen on the handy board while using just straight assembly programs. Is there anyone that has some example code, or know where I can look for explanations of how to do this. Thanks, Joe Hoffmann E-Mail (...) (28 years ago, 20-Jul-98, to lugnet.robotics.handyboard)
 
  Re: LCD routines
 
Hello, I have developed a machine code programming system for programming the handyboard. It is similar to the Buffalo routines on the Motorolla 68HC11 chips. It allows a relatively simple way of machine code interaction to the display. The program (...) (28 years ago, 21-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Need Help to solve the algorithm.
 
May I suggest that you get a copy of a paper that Fred Martin wrote (should be on his website, that is where I got it). It talks about the experience of several of his students and their approaches and pitfalls is designing a robot not too (...) (28 years ago, 21-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Sonar Help!
 
In your message you said: (...) what kind of ext batt are you using? are the diodes in series with that? what voltage do you have on the sonar when it's in operation? are the sonar's ground and the HB's ground connected? fred (...) (28 years ago, 21-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Sonar Help!
 
I have tried the official Handy Board Sonar hookup from the Web sie and didn't get very good results. Most of the time, the sonar would produce seemingly random numbers (including negatives). Every once in a while, it would give a constant value of (...) (28 years ago, 21-Jul-98, to lugnet.robotics.handyboard)
 
  RE: Need Help to solve the algorithm.
 
Are you asking for how to do the ded reckoning from counting steps, or how to get the sonar to measure your location relative to nearby walls? Mike Ross ---...--- From: phillip chia[SMTP:philchia@s...et.com.sg] Sent: Monday, July 20, 1998 3:38 AM (...) (28 years ago, 21-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Need Help to solve the algorithm.
 
The paper referred to is at ftp://cherupakha.med...Martin.pdf My personal advise is that you simply *get started*. hook up your motors and start driving your robot around. see what it can do, how it moves. then connect sensors and gain an intuition (...) (28 years ago, 21-Jul-98, to lugnet.robotics.handyboard)
 
  Memory usage
 
I don't have a handy board but am considering getting one. I like what I have seen so far! I have searched the FAQ and the mail list archives but can't find the answer to my question. How much of the 32k does Interactive C take up? OR MORE TO THE (...) (28 years ago, 21-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Memory usage
 
This question how has an answer in the FAQ. Please see: (URL) is the answer now on the FAQ page. Fred How much of the Handy Board's 32K memory is available for user programs running under Interactive C? Here is an approximate breakdown of how (...) (28 years ago, 21-Jul-98, to lugnet.robotics.handyboard)
 
  Recharging a Battery
 
I have a 'sealed rechargeable' Lead-Acid battery. It's specs are 12 volts at 2.0 Ah. It also has a nifty chart on the outside saying: | Charging @ 20 Deg. C | Voltage Regulation | Initial Current | | Standby Use | 13.50-13.80V | No Limit | | Cyclic (...) (28 years ago, 22-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Recharging a Battery
 
(...) That's a Gel Cell I assume (that's what I call them anyway). Depending on how you use your battery, you can charge it one of two ways (listed on the chart on your battery). I choose to charge my Gel Cells (I have a bunch of different types) (...) (28 years ago, 22-Jul-98, to lugnet.robotics.handyboard)
 
  What about Fischertechnik?
 
I assume the Handy Board (HB) can be used with Fischertechnik products and parts. Is this correct? I just ran across Fischertechnik and was wondering if you all have any comments (preferably based on experience) about how this line of products (...) (28 years ago, 22-Jul-98, to lugnet.robotics.handyboard)
 
  PID filter source code
 
Hello all, Is there anyone hwo has information about motion control, and specially about writing a PID filter for the HC11. I want to control a 3-axis machine. The 3 engines all have encoders and i want to write a PID filter where i can control the (...) (28 years ago, 23-Jul-98, to lugnet.robotics.handyboard)
 
  Config register 0x3c trauma
 
You all may recall my problems downloading to my board and receiving a "config register set to 0x3c" error. I am glad to report there was a very simple solution, but it was a nightmare to debug. So allow me to share my wisdom so other unfortunate (...) (28 years ago, 23-Jul-98, to lugnet.robotics.handyboard)
 
  Re: What about Fischertechnik?
 
REF: Fischertechnik as building components for robots Greetings, We considered using Fischertechnik for building our robots but unfortunately, they occupy more or less the same volume as LEGO parts and our robots had to be small (first within a 12 (...) (28 years ago, 23-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Sonar Help!
 
Fred, I decided not to use the external battery for now and try and get the sonar working using the directions on the web page. Instead of connecting the power throught the Motor Power header, I have simple connect V+ and GND to TIC3's PWR and Grnd (...) (28 years ago, 24-Jul-98, to lugnet.robotics.handyboard)
 
  motor power problems
 
Hi, everyone. I recently bought a preassembled handyboard from the Robot Store in Hong Kong, and I'm having trouble with motor power. My robot frame has two motors that can run at 3-4.5V. I was planning to use 5AA Nicads as a power supply for the (...) (28 years ago, 25-Jul-98, to lugnet.robotics.handyboard)
 
  Re: motor power problems
 
in short, the answer is: "you can't use 3 to 4v motors with the Handy Board." basically, these motors are cheap toy motors that are incredibly noisy from an electrical standpoint, plus they want to draw far more current than the Handy Board's motor (...) (28 years ago, 25-Jul-98, to lugnet.robotics.handyboard)
 
  troubleshooting
 
I have a problem assembleing my hanyboard. I am at the stage where i am doing the digital input circuit. Before this I successfully loaded pcode_hb.s19 into the handyboard and the interactive C message appeared. However, before i loaded pcode_hb.s19 (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  Re: troubleshooting
 
In your message you said: (...) good.... (...) yes, this is normal -- before you load pcode_hb.s19, the LCD is just as you describe. (...) d (...) I'm not clear the problem. if you enable "ignore feedback", does it then download properly? if so, (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  RE: fischertechnik
 
First of all, the HandyBoard works fine with fischertechnik. I've been using fischertechnik for a variety of purposes since about 1980. I've also used Lego Technic, although less extensively, for ten years or so. Size/Scale: If you build identically (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  68hc11F1
 
Hello all, Thanks for all the replies that you have send. My board is now working, at 16 mhz with flash and ram. Richard (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  ELMO
 
Hello all, From December 1997 until now I've been working on my Master's project. It consisted of a theoretical part and a practical part. In the practical part I made a little mobile robot using a Handy Board. In the next couple of weeks I will be (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  Re: IR Emmiter and Detector for RW Pro
 
Hi ! You get a fantastic collection of datasheets and component specs at www.questlink.com regards..... Rajaraman. -----Original Message----- From: Javaid Iqbal <javaid@student.unsw.edu.au> To: Handy Board <handyboard@media.mit.edu> Date: Sunday, (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  Re: troubleshooting
 
ok, i finished the digital input circuit and the first time i turned it on both green and red lights stayed illuminated so i checked the orientation of all the chips and they were correct so i removed and reinserted them for good measure. This (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  Various Basic Issues
 
Howdy from Texas. I have set myself the goal of making a robot with the handyboard -- just for the learning of it. Until 2 days ago I had zero knowledge of electronics, although I am teaching myself using some kits and books. I also do not know C (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  Re: motor power problems
 
In a message dated 98-07-24 20:49:35 EDT, you write: << Has anyone had similar problems, and if so how did you solve them? I know there's a way to provide a separate power supply for the motors, but I'd rather not cut traces on the board except as a (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Sumo-Robots
 
look at (URL) for th Dutch sumo-robotics Greetz Emiel ---...--- (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  sonar.c for the handyboard
 
Hello, I have a handyboard and 6500 series poloroid ultrasonic ranging system. I have downloaded the sonar.c programs used to drive the transducer for distance measurements. There appears to be a problem, or atleast I think there is, with it. The (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  IC Floating Point Bug
 
I've been making use of floating point for the first time on the HB and am having problems. The following program demonstrates the kinds of bugs I've been encountering: ----(cut here)---...--- int main() { float a; float b; float c; /* This program (...) (28 years ago, 27-Jul-98, to lugnet.robotics.handyboard)
 
  [Fwd: Various Basic Issues]
 
-- MIME ATTACHMENTS DISCARDED: 1. Content-Type: message/rfc822 Content-Transfer-Encoding: 7bit Content-Disposition: inline Content-Length: 1148 (28 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
 
  FS: Extra HandyBoard for sale
 
I have one extra HandyBoard that I will sell if anyone needs one. It is a fully assembled and tested board with Serial Interface/Charger Board and cases. It has never been used in a project (about 2 months old). I built two of these and find that I (...) (28 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
 
  Re: Various Basic Issues
 
<snip!> (...) I believe it is a subset of striaght C. However, I never learned C: I junped straight into C++ before even getting my HB. However, programming was of no dificulty to me, even thought I only knew C++ (...) IC will work on a computer. I (...) (28 years ago, 28-Jul-98, to lugnet.robotics.handyboard)
 
  Digital In and Analog Out Header
 
Hello All, Just a quick question, On the handyboard there is a socket header for the 7 analog inputs, and 9 digital outputs. There is actually three rows of headers for these inputs. I am enquiring as to what are the three headers for? I am (...) (28 years ago, 28-Jul-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR