To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *47269 (-100)
  motor command question
 
Why would two motors, set to turn and with unlimited chosen for time out, only turn a couple of times and stop. this motor command is the only command in the program. patty (19 years ago, 3-Dec-07, to lugnet.robotics.nxt)
 
  Re: NXT compatible bluetooth adapters
 
Besides, there's an according list on the official LEGO MINDSTORMS NXT site: (URL) certainly not complete, though, but a starting point (and they may be interested in the results of this discussion as well). As for BlueSoleil, I could not get it (...) (19 years ago, 3-Dec-07, to lugnet.robotics)
 
  Re: NXT compatible bluetooth adapters
 
I bought the Kensington 33085 and have had that working fine on 3 different PCs. I also bought a no-name bluetooth adapter that uses the BlueSoliel software. I was able to get that one working on the PCs as well. The Kensington, bought for about $50 (...) (19 years ago, 3-Dec-07, to lugnet.robotics)
 
  Re: NXT compatible bluetooth adapters
 
I bought one of those "no name" adapters (with Bluesoleil software) $10 (Australian). Of course, plug and no-go. Then I found this: (URL) working now. The adapter has been identified as "ISSC USB Bluetooth Device". (...) (19 years ago, 3-Dec-07, to lugnet.robotics)
 
  Re: Nxc and Mindsensors stuff
 
(...) Thank you! But it worked only after firmware upgrade (to version 1.05) and using original NXT flat cables (Mindsensors flat cables are very poor quality). -- alf (19 years ago, 30-Nov-07, to lugnet.robotics.nxt)
 
  Re: recharging NXT battery block with DC adapter?
 
My NXT Charger came with my battery. The output of the charger is 10.8 volts, 700 ma 8W. I would just buy the Lego charger. After reaching a full charge, the charger goes into a trickle charge mode. "Pavel Petrovic" <pavel.petrovic@gmail.com> wrote (...) (19 years ago, 30-Nov-07, to lugnet.robotics.nxt)
 
  Re: recharging NXT battery block with DC adapter?
 
(...) Whew! I was going to put my question in past tense ("Does this mean that I should have or shouldn't have used the train controller plug ...") but it seemed better to be a fool after doing something not dumb than after doing something dumb! (...) (19 years ago, 30-Nov-07, to lugnet.robotics.nxt)
 
  Re: recharging NXT battery block with DC adapter?
 
(...) You should. The NXT battery expects the same wallwart as the train controller and RCX. Philo (19 years ago, 30-Nov-07, to lugnet.robotics.nxt)
 
  Re: recharging NXT battery block with DC adapter?
 
(...) Brian, So, does this mean that I should or I shouldn't use the train controller plug thingy that I use for the trains and my RCX? Rafe (19 years ago, 30-Nov-07, to lugnet.robotics.nxt)
 
  Re: recharging NXT battery block with DC adapter?
 
(...) I'd say a bad idea, since it's supposed to be supplied with 9-12V *AC* (not DC) power. Like the RCX 1.0, it might work under a DC supply... but that's not what it was designed for. (19 years ago, 30-Nov-07, to lugnet.robotics.nxt)
 
  recharging NXT battery block with DC adapter?
 
Hi, Can anybody confirm whether recharging a NXT battery block using 9V or 12V DC adapter is a bad or good idea, please? Seems that LEGO published HW schematics for the brick, but not for the battery block... Pavel. (19 years ago, 30-Nov-07, to lugnet.robotics.nxt)
 
  NXT Power Programming book
 
As a convinced fan of graphical both programming environments : ROBOLAB and NI NXT toolkit, I would like to share with you how much I appreciate the tremendous work John Hansen has done in the development of BricxCC and more recently in his new book (...) (19 years ago, 28-Nov-07, to lugnet.robotics)
 
  Re: Nxc and Mindsensors stuff
 
(...) Well, I use Linux so I completely skipped the part about NXT-G in the docs and I missed the reference to the light sensor. Anyway, that is sort of what I tried (I changed the original program so many times I am not sure). But probably I missed (...) (19 years ago, 27-Nov-07, to lugnet.robotics.nxt)
 
  Re: Nxc and Mindsensors stuff
 
(...) I do not have the mindsensors DROD-Nx sensor but I have read the documentation from their website. It says that the sensor is an analog sensor which you can read using the standard NXT-G light sensor block. That means you need to configure the (...) (19 years ago, 27-Nov-07, to lugnet.robotics.nxt)
 
  Re: Nxc and Mindsensors stuff
 
(...) To use the DIST-Nx sensor from mindsensors.com you can use the code at this url: (URL) sure you initialize the sensor using the correct type and properly energize it after you configure the port as a lowspeed port. The sample program is setup (...) (19 years ago, 27-Nov-07, to lugnet.robotics.nxt)
 
  Re: Nxc and Mindsensors stuff
 
Il giorno 12-nov-2007, alle ore 16:59, GiP ha scritto: (...) Hi, I finally got my mindsensors stuff (including a DIST-Nx) and am still figuring out how to use them with NXC. It seems we need only two functions: - a "do a full initialization" one: (...) (19 years ago, 26-Nov-07, to lugnet.robotics.nxt)
 
  RE: RoboLab
 
Tom. I just read your website. Very Interesting work Just my 2 cents. I'm sure there are more input from the guru out there though. --Elizabeth -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...ugnet.com] On Behalf Of (...) (19 years ago, 25-Nov-07, to lugnet.robotics.rcx.robolab)
 
  RE: RoboLab
 
[--] "...Are you suggesting I purchase ROBOLABT 2.9 upgrade from my RoboLab 2.5.4B? Tom, but you must be aware of the risk of using an obsolete product. Honestly though, 2.9.4 is SO solid for most of the rather sophisticated algorithms already for (...) (19 years ago, 25-Nov-07, to lugnet.robotics.rcx.robolab)
 
  Looking for VisionCenter Examples
 
I will be developing a program that distills a real time image into a aesthetic number using frequency & spatial filtering, quantitative, morphology and pattern matching through the VisionCenter. My reference work will be to use known masterpieces (...) (19 years ago, 25-Nov-07, to lugnet.robotics.vc)
 
  Re: RoboLab
 
(...) Thank you Elizabeth, I am moving towards using LabView with a patch to allow me to run my RCX robot. I am concentrating on RoboLab 2.5.4B and the RCX. (URL) I have a few questions: Are you suggesting I purchase ROBOLAB™ 2.9 upgrade from my (...) (19 years ago, 25-Nov-07, to lugnet.robotics.rcx.robolab)
 
  RE: RoboLab
 
You need purchase a copy from legoeducation.com, then download the latest 2.9.4 patch from legoengineering.com (unless legoeducation has already had the patch from their website). The 2.9.X is a gigantic improvement from 2.5. I still do not agree (...) (19 years ago, 20-Nov-07, to lugnet.robotics.rcx.robolab)
 
  RoboLab
 
Is anyone looking at these posts? I think I am out of the loop. (URL) seems to be the place to go. Where does one go for fascinating RoboLab programing? (19 years ago, 20-Nov-07, to lugnet.robotics.rcx.robolab)
 
  Re: BricxCC etc vs. MS Robotics Studio
 
Dear list, I tried to look this up a little on the (URL) site but could not find it easily: could you please tell me where I can find information or user feedback about use of the MSRS with the RCX? Is it a reasonable choice for fast prototyping and (...) (19 years ago, 19-Nov-07, to lugnet.robotics)
 
  Re: Nxc and Mindsensors stuff
 
(...) Actually, I have them. But it didn't help, I tried to use the I2C functions and the usual SetSensorType but I cannot get a meaningful number, maybe I am doing something wrong. Does anyone have an example of a NXC program that read a (...) (19 years ago, 19-Nov-07, to lugnet.robotics.nxt)
 
  Re: Displaying multiple variables
 
(...) There's also Steve Hassenplug's Display Number block (find it here (URL) along with some other NXT-G goodies). I use this all the time to display values for debugging. John (19 years ago, 19-Nov-07, to lugnet.robotics.nxt)
 
  Re: Nxc and Mindsensors stuff
 
It seems you don't have the latest NXC*.h header files (found in source release of NXC, not in the binary releases), as well as the latest NXC_Guide.pdf describing I2C functions. alf Il giorno 12-nov-2007, alle ore 16:59, GiP ha scritto: (...) -- (...) (19 years ago, 18-Nov-07, to lugnet.robotics.nxt)
 
  Re: Displaying multiple variables
 
(...) Nice. Thanks very much. When I get to my computer, I'm going to check to see how I missed the "Clear Screen" checkbox. (19 years ago, 17-Nov-07, to lugnet.robotics.nxt)
 
  Re: Displaying multiple variables
 
(...) There are lots of ways to display such information on the NXT LCD. The easiest is probably to draw one number, and then use a second Display block to draw a second number - just uncheck the "clear screen" checkbox on the second Display block. (...) (19 years ago, 17-Nov-07, to lugnet.robotics.nxt)
 
  Displaying multiple variables
 
Yesterday, I had a student who wished to display two numeric variables on the screen. We ended up multiplying the first by 1000 then adding the second. This we displayed and read as a packed variable with two shifted values. How can we do this more (...) (19 years ago, 17-Nov-07, to lugnet.robotics.nxt)
 
  Format of the NXT-G program files?
 
Hi, Am I correct that there are no utilities for inspecting the NXT-G programs created with the RoboLab for NXT? I mean: printing the programs created in NXT-G in some human-readable format? Any documentation about the binary format anywhere? (...) (19 years ago, 8-Nov-07, to lugnet.robotics.nxt)
 
  Nxc and Mindsensors stuff
 
Hi, we just bought some sensors from mindsensor.com but I cannot find any info on how to use them with nxc. I have seen that b33 has two new API but there is no "generic" info on how to use them and the mindsensor.com site has no info or sample (...) (19 years ago, 12-Nov-07, to lugnet.robotics.nxt)
 
  NXT Sumo - NXTize it all!
 
Some of us here in Indiana and surrounding areas recently got together for a "just for fun" sumo event. We didn't keep score, and in fact the goal was to use stock LEGO models as much as possible. We started out with making five copies of the #8275 (...) (19 years ago, 12-Nov-07, to lugnet.technic, lugnet.robotics)
 
  Resetting TachoCount in LCP
 
Hi, I'm wondering how to reset a tachometer via the Lego Communication Protocol. Of the three tachometer readings, TachomCount, BlockTacho and RotationCount, I can only see how to reset the latter two using ResetMotorPosition (Bluetooth Developer (...) (19 years ago, 10-Nov-07, to lugnet.robotics.nxt)
 
  NXT Software Version 1.1
 
It looks like we will be purchasing an NXT when we visit Carlsbad Thanksgiving week. Now comes the question of software. The computer where we do most programming is a Vista Home Premium eMachine desktop. The computer where we play most is an XP (...) (19 years ago, 9-Nov-07, to lugnet.robotics)
 
  Installing LeJOS on Linux (Fedora Core 6)
 
My sysadmin is trying to install LeJOS for me on our Linux servers. He's having a problem detailed in what I'm posting below. Does anyone have any ideas on what's going wrong? Thanks, Peter Copied message: ***...*** I am trying to build on a fedora (...) (19 years ago, 8-Nov-07, to lugnet.robotics.nxt)
 
  BricxCC release 3.3.7.17
 
I posted a new official BricxCC release yesterday: 3.3.7.17. This release includes substantially improved help content for NBC and NXC as well as a built-in NBC compiler (beta 33). If you've been using the latest test release there isn't much new (...) (19 years ago, 6-Nov-07, to lugnet.robotics, lugnet.robotics.nxt)
 
  Re: Datalogging with the NXT
 
(...) :) I know. I have the book. What I was specificly asking about was logging roller coasters or other such rides. One of the early datalogs I did was to monitor the light level near a window along with the sound level for three days. You could (...) (19 years ago, 31-Oct-07, to lugnet.robotics)
 
  Re: Datalogging with the NXT
 
(...) There are step-by-step instructions for using the data logging feature of the NXT for measuring light level and similar experiments in the Extreme NXT book. The book also shows how to import the text data files to spreadsheet programs. You can (...) (19 years ago, 31-Oct-07, to lugnet.robotics)
 
  RE: Datalogging with the NXT
 
(...) There was a TV show on the Discovery Channel or one of the other science channels a couple of years back on exactly this topic. It was one of the "kids do science things" type of show. They used some other logging device. Unfortunately I have (...) (19 years ago, 31-Oct-07, to lugnet.robotics)
 
  Datalogging with the NXT
 
OK, I've got to admit that this isn't exactly "robotics". In fact, it must be about the smallest "robot" I've ever made, in that it was really just the NXT and a single sensor, with a few 3L pins and a studless beam to secure the sensor. But the (...) (19 years ago, 31-Oct-07, to lugnet.robotics)  
 
  NXT robot that does Wii bowling
 
No, this isn't mine. I just happened across it today: (URL) (19 years ago, 30-Oct-07, to lugnet.robotics)
 
  Re: Replenishing NXT Educational sets
 
(...) I wondered about that. My search arguments weren't good enough to reveal the right Bricklink part number. Thank you very much! (19 years ago, 26-Oct-07, to lugnet.robotics.nxt)
 
  Re: Replenishing NXT Educational sets
 
(...) Bricklink does not have the same part number for this piece as Peeron/LDRAW. Use this part number: (URL) You will find hundreds for sale. (19 years ago, 26-Oct-07, to lugnet.robotics.nxt)
 
  Replenishing NXT Educational sets
 
The Edu Set has two 1x13 Technic Beams, (URL) The models presented in all the curriculum materials are absolutely dependent on these 1x13 beams. Bottom line, a missing 1x13 beam causes students a lot of grief, consternation, discouragement, (...) (19 years ago, 25-Oct-07, to lugnet.robotics.nxt)
 
  Re: nbc gives error for SendRemoteString
 
(...) This is caused by a typo bug in the NXTDefs.h header that I accidentally introduced in beta 32. If you are running on a Windows box you can download a pre-release of beta 33 from the test_release.zip on the BricxCC page. I will have beta 33 up (...) (19 years ago, 25-Oct-07, to lugnet.robotics.nxt)
 
  Four-stroke pneumatic pump
 
Here is my last creation, a four-stroke pneumatic compressor. (URL) only special parts are the small pumps and the crankshaft pieces. This compressor can also be build up partly. I mean you can use one or two pumps instead of four. Depending on the (...) (19 years ago, 25-Oct-07, to lugnet.robotics, lugnet.announce) ! 
 
  nbc gives error for SendRemoteString
 
Hi, has there been an undocumented change in the last nbc? I have some programs that use SendRemoteString and I cannot compile them any more (they compile with older versions). This minimal prog: ---...--- task main() { string out; out="String"; (...) (19 years ago, 23-Oct-07, to lugnet.robotics.nxt)
 
  Walker useing new leg design
 
After a few long weeks of tinkering, I think Ive settled on a final design that I would like to display at the (URL) Toronto Hobby show.> (URL) This is a six leg walker, that uses the leg design of (URL) Theo Jansen> After seeing his video (URL) (...) (19 years ago, 19-Oct-07, to lugnet.technic, lugnet.org.ca.rtltoronto, lugnet.robotics, lugnet.announce.moc, FTX) !! 
 
  Re: Source Code Changes in NXT Firmware Version 1.05
 
(...) The changes between 1.03 and 1.04 are far more extensive than the changes from 1.04 and 1.05, if you lump the support for ADPCM compression into a single change (which involves c_sound.c, d_sound.c, d_sound.h, d_sound.r, d_sound_adpcm.r, and (...) (19 years ago, 18-Oct-07, to lugnet.robotics, lugnet.robotics.nxt)
 
  Source Code Changes in NXT Firmware Version 1.05
 
I haven't seen it previously mentioned but the open source firmware for version 1.05 is downloadable from the LEGO Mindstorms web site. I did a WINDIFF on the various source files to see what has changed in this release. I then manually examined the (...) (19 years ago, 17-Oct-07, to lugnet.robotics, lugnet.robotics.nxt)
 
  Re: Powering 9v Trains using the NXT
 
(...) Are you using the NXT on batteries alone, or using the Li-ion battery pack so you can plug the NXT into a wall for more consistant power? (...) As others have noted, this has worked well with the RCX. It's essentially how the GBC trains are (...) (19 years ago, 17-Oct-07, to lugnet.robotics, lugnet.org.us.ulug)
 
  Re: Powering 9v Trains using the NXT
 
(...) I'm not sure if there's a better way, and I haven't tried it with an NXT, but I've had good luck with option 2 using an RCX. I isolated the track by putting a bit of clear tape over the ends that connect to the other track sections. -Elroy (19 years ago, 17-Oct-07, to lugnet.robotics, lugnet.org.us.ulug)
 
  Powering 9v Trains using the NXT
 
To all, I would like to find a way (simple way that is) to power our LTC 9v trains using both the standard LEGO 9v train modulator and the NXT. We have attempted the following: 1- Power the train simply using the NXT and the converter cables. Too (...) (19 years ago, 17-Oct-07, to lugnet.robotics, lugnet.org.us.ulug)
 
  Ultrasonic sensor calibration settings
 
Hi, Has anyone tried using the standard NXT Ultrasonic sensor calibration settings? I've been doing a little work on the leJOS i2c interface and although I can read both the factory default values and the current settings I do not seem to be able to (...) (19 years ago, 17-Oct-07, to lugnet.robotics.nxt.nxthacking)
 
  Re: ARM Assembly Language Programming on NXT?
 
Hi T.C. (...) aha. I just programmed some startup and interrupt wrapper code (the rest is C), so I didn't get into the higher reaches of macros etc. Jürgen (19 years ago, 16-Oct-07, to lugnet.robotics.nxt.nxthacking)
 
  Re: ARM Assembly Language Programming on NXT?
 
(...) Sorry, I found a more recent version, but it's still missing some parts on the ARM architecture: (URL) also found the following Intro guide (which is better than nothing): (URL) (19 years ago, 16-Oct-07, to lugnet.robotics.nxt.nxthacking)
 
  Re: ARM Assembly Language Programming on NXT?
 
Hi Juergen, Thanks for replying. (...) Thanks for the info. My goal is to run and debug ARM assembly language programs executing in RAM. I was not familiar with the NXT, so currently I'm looking at the on-board capabilities. I realized after some (...) (19 years ago, 16-Oct-07, to lugnet.robotics.nxt.nxthacking)
 
  Re: Prime number generator
 
(...) SetUserDisplay hooks up the display to whatever source you specify and until you tell it to hook up to a different source it will continue to display the value of that source until the program ends. The first time that your NQC code enters the (...) (19 years ago, 15-Oct-07, to lugnet.robotics)
 
  (In)compatibility of RC Trains and Power-Functions
 
I am trying to determine whether there is any compatibility between the RC trains infrared remote-control protocol and the Power-Functions infrared-protocol. Does anybody know definitely whether a Power-Functions transmitter has any effect on an (...) (19 years ago, 14-Oct-07, to lugnet.trains, lugnet.robotics, lugnet.technic)
 
  Re: ARM Assembly Language Programming on NXT?
 
Hi T.C., (...) I have an AT91SAM7S-EK here, it has 4 LEDs and 4 touch buttons. It should also be fairly easy to write a driver for one of the serial ports (polling would suffice for a start). On the NXT the only I/O that is easy to use with the (...) (19 years ago, 14-Oct-07, to lugnet.robotics.nxt.nxthacking)
 
  Prime number generator
 
I've been trying to write a prime number generator in NQC by way of exercise to improve my programming skills, but I've run into some unexpected trouble. I have two sets of code that are virtually identical, one in NQC and the other in plain C. The (...) (19 years ago, 13-Oct-07, to lugnet.robotics)
 
  NXT Power Programming
 
I’d like to officially announce that Variant Press will soon publish my new book, NXT Power Programming. It should be available November 7th. You can pre-order it now at Amazon.com or Variant Press. I hope everyone who purchases a copy of NXT Power (...) (19 years ago, 11-Oct-07, to lugnet.announce, lugnet.robotics, lugnet.robotics.nxt) ! 
 
  Re: Mindstorms NXT 1.1
 
(...) Thanks Matthias, I did read that discussion; but I hadn't realized the people who said they called actually received it for free. My understanding was that they were in countries were it's listed as "not available yet" (such as Germany or (...) (19 years ago, 10-Oct-07, to lugnet.robotics.nxt)
 
  Re: Mindstorms NXT 1.1
 
Thanks Philo, I should have thought to check nxtasy on the subject. Looks like there are a lot of improvements; but then again what interests me most is full support of my computer, which the current software doesn't provide. A patch, in short. On (...) (19 years ago, 10-Oct-07, to lugnet.robotics.nxt)
 
  Re: Mindstorms NXT 1.1
 
There has been an according post on THE NXT STEP one week ago ((URL) a lot of comments of users there state that they have received it free of charge. I also do not understand why it is not available in Germany - that's ludicrous for an (...) (19 years ago, 10-Oct-07, to lugnet.robotics.nxt)
 
  Re: Power Functions presentation
 
(...) I did it, I'll try to update my page with some internal photos. (...) The battery box delivers power through power lines (used by IR receiver) if the switch is not in neutral position, and C1 C2 whose polarity depends on switch position (and (...) (19 years ago, 10-Oct-07, to lugnet.robotics.nxt, lugnet.technic)
 
  Re: Mindstorms NXT 1.1
 
(...) You are not alone thinking that: (URL) there are indeed a lot of improvements: (URL) (19 years ago, 10-Oct-07, to lugnet.robotics.nxt, FTX)
 
  Re: Power Functions presentation
 
"Philippe Hurbain" <philohome@free.fr> wrote in message news:JpHqA1.FM@lugnet.com... (...) built internally? Your page seemed to suggest that someone had actually taken them apart, but there was no more information on there. Apart from the obvious (...) (19 years ago, 10-Oct-07, to lugnet.robotics.nxt, lugnet.technic)
 
  Mindstorms NXT 1.1
 
Hi, I don't think I've seen it here yet, but apparently LEGO is finally releasing version 1.1 of the NXT software. It will be available on Shop@Home: (URL) So far it seems it's not available in all countries yet, but a phone call might work. To me (...) (19 years ago, 9-Oct-07, to lugnet.robotics.nxt, FTX)
 
  robo soccer
 
I wonder if there is anyone who has experience with the following book: RoboCup 2002: Robot Soccer World Cup VI (Lecture Notes in Computer Science) I have a group of students are working on robosoccer game using nxt with RobotC. Recommendation? (19 years ago, 9-Oct-07, to lugnet.robotics.nxt)
 
  Re: The Future of Trains
 
(...) You are right, the main limitation probably comes from wall wart... You are essentially right for the 0.7A current (though it is not hard limit, rather a safety one). Philo (19 years ago, 9-Oct-07, to lugnet.lego, lugnet.robotics.nxt, lugnet.trains)
 
  Re: ARM Assembly Language Programming on NXT?
 
(...) Thanks for the tip. I glanced at (URL) previously but I must've missed it thinking it's Java based. (...) Are you referring to the default NXT firmware or the LEJOS NXJ/OSEK firmware? (...) You're right, I've come across several ARM-based SBC (...) (19 years ago, 9-Oct-07, to lugnet.robotics.nxt.nxthacking)
 
  Re: ARM Assembly Language Programming on NXT?
 
(...) Thanks Dick for intruducing LEJOS OSEK, When we develolped LEJOS OSEK, Prof. Mizuno wrote several GCC assembly code to port TOPPERS OSEK (an open source OSEK OS) to NXT. Whole assembly code(*.S) is stored in lejos_osek\toppers_o...1sam7s-gnu (...) (19 years ago, 9-Oct-07, to lugnet.robotics.nxt.nxthacking)
 
  Re: The Future of Trains
 
(...) The Australian LEGO wall wart is marked 10V @ 7VA on the secondary. I don't recall all the stuff I learnt about the relationship between VA and W, but that seems to me to indicate about 0.7A. I believe this generally reduces as load increases, (...) (19 years ago, 8-Oct-07, to lugnet.lego, lugnet.robotics.nxt, lugnet.trains)
 
  Re: The Future of Trains
 
(...) At BayLTC we usually run four train motors on one loop using stock Controller with a 1.2 amp wall wart. Bruce (19 years ago, 8-Oct-07, to lugnet.lego, lugnet.robotics.nxt, lugnet.trains)
 
  Re: The Future of Trains
 
(...) The linear regulator inside is a 1.5A version if I remember well, but I may be wrong. Cross posted to lugnet.trains trying to get train guru opinion... Philo (19 years ago, 8-Oct-07, to lugnet.lego, lugnet.robotics.nxt, lugnet.trains)
 
  RE: ARM Assembly Language Programming on NXT?
 
Do a Google on "LEJOS OSEK". I believe this is a solution that has taken the base "OS" from the NXJ JAVA byte code interpreter as the basis for programming the NXT using GCC C++. I assume if you can use the GCC C/C++ tools with the NXT then you (...) (19 years ago, 8-Oct-07, to lugnet.robotics.nxt.nxthacking)
 
  Re: The Future of Trains
 
(...) Philo kindly corrected me, pointing out that the NXT outputs are regulated down to 1 A, so you couldn't run a dual-truck train all the way to stall. You could still get a good bit of the way there, however. Does anyone know what the peak (...) (19 years ago, 8-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Re: The Future of Trains
 
(...) Ah, thank you - so running two stalled train motors would exceed the NXT output, but running one train motor up to a stall conditions should be fine. Out of curiosity, along with the output limitations on the NXT (1 A) and RCX (500 mA), does (...) (19 years ago, 8-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Re: The Future of Trains
 
(...) Some precisions here: - NXT stall current is 2A but only for a short time: internal thermal protection will trip at a current much lower than that (exact value depends on temperature and overload duration). A practical value is about 1A - NXT (...) (19 years ago, 8-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  ARM Assembly Language Programming on NXT?
 
Hi, I just stumbled on this newsgroup/website while searching for kits for teaching Assembly Language programming to undergraduate students in Comp. Science in an interesting (interactive) manner. I'm primarily interested in the ARM instruction set. (...) (19 years ago, 8-Oct-07, to lugnet.robotics.nxt.nxthacking)
 
  Re: The Future of Trains
 
(...) So it sounds like a single loop should be no problem under most situations, since I'm not sure I've heard of anyone running three motors on a single train (there's the same issue with how much amperage a power regulator can push). (...) It (...) (19 years ago, 8-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Re: The Future of Trains
 
(...) Stalled, the train motor pulls 950 mA, while the stall current of the NXT motor is a whopping 2 Amps. So a single NXT motor output should easily handle a twin-engine train loaded to the point where it stalls the engine(s)... there's the matter (...) (19 years ago, 7-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Re: The Future of Trains
 
(...) Fair enough, but clearly the idea has sparked some interest, so I'm sure I'll see it get put into use at some point. (...) The ports may be able to pour out power, as you say, but I'd say it's equally well established that large trains with (...) (19 years ago, 7-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Re: The Future of Trains
 
(...) As Ross mentioned, I was focused more on the "future" of trains, and if it's going to be done in LEGO, it looks like it will be done without conductive track. (...) Absolutely, but you could do better. Run a single loop off a single output, (...) (19 years ago, 6-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Power Functions presentation
 
I have updated my website with a presentation of the new Power Functions system, including: # Overview of Power Functions range # Description of working # Comparison with older 9V mini-motors # LDraw and LeoCAD part files (URL) motors comparison (...) (19 years ago, 6-Oct-07, to lugnet.announce, lugnet.technic, lugnet.robotics, lugnet.trains) !! 
 
  Re: The Future of Trains
 
(...) I believe the options being discussed were in relation to the use of non-metal track, which is all that will be produced by LEGO in the foreseeable future. ROSCO (19 years ago, 6-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Re: The Future of Trains
 
(...) Oh, for shame, Brian. Letting me think up an option that you passed right over (and a really cool one at that). With the legacy converter cables, you could power the _track_ with an NXT. Hook the track up as if it was a motor, using the (...) (19 years ago, 6-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Re: The Future of Trains
 
(...) Not exactly, that I know of, *yet*... The biggest problem in running a train would be hiding the NXT - I saw only one good solution to hiding the RCX in a boxcar, and the NXT is bigger, as are the motors. You could use an old motor (or even a (...) (19 years ago, 6-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Re: The Future of Trains
 
In lugnet.lego, Scott Wardlaw wrote: <snip> (...) <snip> Has anyone adapted two NXT units to drive a train yet? One NXT as a controller talks bluetooth to the other NXT that drives the train. The NXT that drives the train could be either attached to (...) (19 years ago, 5-Oct-07, to lugnet.lego, lugnet.robotics.nxt)
 
  Re: Wonderful design tidbits PDF - anybody else impressed?
 
(...) Don't let Brian's and Philo's understatements lead you to believe that this book, a collection of hundreds of ultra-high quality photos arranged in a stunningly simple succession of nearly uniform page layouts, is anything but the finest (...) (19 years ago, 5-Oct-07, to lugnet.technic, lugnet.robotics)
 
  Re: Wonderful design tidbits PDF - anybody else impressed?
 
(...) I am impressed. This "book" is simply delightful. Many useful tips, wonderful presentation... Highly recommanded! Philo (19 years ago, 5-Oct-07, to lugnet.technic, lugnet.robotics)
 
  RoboFest Hawaii
 
The Second Annual RoboFest Hawaii robotics competition and engineering fair will be held on Saturday, November 17 from 10:00 am to 2:00 pm at the University of Hawaii at Hilo Gym. RoboFest Hawaii is a high-technology and engineering fair thinly (...) (19 years ago, 2-Oct-07, to lugnet.robotics)
 
  Re: Cirque des Sciences
 
(...) (19 years ago, 29-Sep-07, to lugnet.robotics)
 
  STriDER 2.0 -- tripedal robot
 
This robot walks on three legs, but not in the way you'd expect: (URL) (19 years ago, 25-Sep-07, to lugnet.robotics, lugnet.technic)
 
  eZCIRCUITS #2 Is Available
 
Hi All, I've just posted another eZCIRCUITS to my blog (URL). This application will show how to build a Bumper Sensor-Switch with the help of the LEGO NXT for mobile robots and mechatronics platforms. Enjoy!!! Don W. (19 years ago, 22-Sep-07, to lugnet.robotics.nxt)
 
  Re: New pbLua Beta13o - Now with FLASH Writing!
 
(...) Hi Ralph, WOW, great work!!! It works perfectly... Some additional notes and documentation about storing Lua programs at flash memory is available at: (URL) for your excellent support Christian (19 years ago, 20-Sep-07, to lugnet.robotics.nxt)
 
  Cirque des Sciences
 
For those who want to meet our robot team, sharing older and more recent robot creations "life", you are invited to the Luxembourg "Cirque des Sciences" ((URL) that will happen this weekend. There will be GASTON, Erik's xy-plotter, (...) (19 years ago, 20-Sep-07, to lugnet.robotics)
 
  Re: Any Good Fan Instructions Using Only One NXT Set?
 
(...) Thanks Matthias. That's just the kind of thread I was looking for. -Paul (19 years ago, 20-Sep-07, to lugnet.robotics.nxt)
 
  Re: Any Good Fan Instructions Using Only One NXT Set?
 
(...) Yes, this helps a lot. I'll definitely check out your book when it comes out. Thanks! -Paul (19 years ago, 20-Sep-07, to lugnet.robotics.nxt)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR