To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3201 (+100)
  6.270 ROBOT COMPETITION
 
FF> If you're making a family outing of it, my advice is to show up no FF> later than 4:30, drop the advance party off at the Mass Ave entrance FF> to get in and hold seats, and then have the remaining party park the FF> car and show up with pizza (...) (29 years ago, 3-Feb-98, to lugnet.robotics.handyboard)
 
  re: pcode that works without LCD
 
For the freeware IC, see (URL) Fred (29 years ago, 3-Feb-98, to lugnet.robotics.handyboard)
 
  68hc811e2 config reg.
 
My handyboard works great,with a 68HC11A1 mcu. The config of the 103f register was done in one try and had no problems. I then installed a 68HC811E2 MCU, (a 2k EEPROM version of the original). Using DLM, HBDL and PCbug to try set the config register (...) (29 years ago, 4-Feb-98, to lugnet.robotics.handyboard)
 
  Connecting a second sonar module
 
I'm curious about connecting two of the Polaroid sonar modules to the Handy Board v1.2. Does anyone know whether ports PD2, PD3 and TIC2 can be used to hook up the second unit in the same way that PD4, PD5 and TIC3 are used for one unit? Or is there (...) (29 years ago, 4-Feb-98, to lugnet.robotics.handyboard)
 
  9600 Baud
 
I'm sure that this has been posted tons of times, but I am trying to use the 9600 serial library. I can't seem to get anything to echo on Zterm. I used a phone cable and hooked it up to digital port 9, and then to the HB serial/charger. I get (...) (29 years ago, 4-Feb-98, to lugnet.robotics.handyboard)
 
  Smooth PWM routines
 
We are using the handyboard to control our mobile robot and wish to install the Skidmore smooth PWM routines as provided on the Handyboard web site. We are using Dunfield micro-C compiler version 3.1 in Windows95 along with the handyboard library (...) (29 years ago, 4-Feb-98, to lugnet.robotics.handyboard)
 
  Config reg.
 
Using DL pcode_hb.s19 I got the following msg about 12 times, only on the 811e2 chips, the A1'a I could set the config to anything and change it back. Please place board in download mode and press RETURN To quit, press Q For help, press H (...) (29 years ago, 4-Feb-98, to lugnet.robotics.handyboard)
 
  Re: 9600 Baud / help with pa7
 
(...) Perhaps you have the RJ11 cable wired wrong. Make sure you have the ground signal and the data from pa7/digital 9 connected. see below... (...) Looking at the digital and analog sensor headers: live signal [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ (...) (29 years ago, 5-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Connecting a second sonar module
 
(...) Sure, there's no reason you could set it up to use PD4, PD5, and TIC3 for a 2nd sonar. you might be able to get away with some signal multiplexing, assuming you're only firing one sonar at a time. i could see the BINH being no problem. For (...) (29 years ago, 5-Feb-98, to lugnet.robotics.handyboard)
 
  Problems starting IC
 
I'm at the phase of bringing up a handyboard till a point where I have to start IC for the first time (chapter 6.0.5). I did succeed to download the PCODE_HB.S19 code and the board is starting with a beep and the IC startup message. So, that seems (...) (29 years ago, 5-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Problems starting IC
 
Maarten -- Quickly I can make the guess that your local copy of PCODE_HB.S19 is corrupt. The fact that PCODER22.S19 works indicates there's nothing wrong with your board. Try re-downloading PCODE_HB.S19 from the web site? Fred In your message you (...) (29 years ago, 5-Feb-98, to lugnet.robotics.handyboard)
 
  Modem Cable
 
The "modem cable" used to connect the computer to the serial interface/charger: Is this a "null modem" cable with the transmit & receive lines (pins 2 & 3) crossed, or is is a straight pin-to-pin serial cable? Thanks, Brett Anthony Research (...) (29 years ago, 5-Feb-98, to lugnet.robotics.handyboard)
 
  encoder function
 
The encoder function pages say that for the fast encoder, the refresh rate is only 1 KHz. That is it can make only 1000 increments in a second. If I have an encoder that has a change rate on the order of a micro second, is there any reasonable way (...) (29 years ago, 5-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Modem Cable
 
It is straight-thru. Please note that if you are connecting from a 9-pin male PC port to the HB interface's 25-pin female, the means that you have the following mapping: DB-9 DB-25 2 3 3 2 5 7 In other words, the same cable as you would use to (...) (29 years ago, 5-Feb-98, to lugnet.robotics.handyboard)
 
  analog input test
 
Fred; I am at the testanalogs portion of the assembly process. All has gone well up until this point. The knob varies between 0 and 255 as expected and the seven numbers all come up either 254 or 255 when I press the START button. However I am (...) (29 years ago, 5-Feb-98, to lugnet.robotics.handyboard)
 
  Sonar
 
Has anyone used the diagrams off the HB wesite for connecting the 6500 sonar. If so, could someone please tell an ignorant CS major, what the six diodes are for, and if anything else can be substituted for them. My local Radio Crack seems to be out (...) (29 years ago, 6-Feb-98, to lugnet.robotics.handyboard)
 
  Re: encoder function
 
Hi all I have written some routines to measure frequencies from 30Hz to 30kHz. I'm posting this with an attachement because several people have ask me already for these routines. To Fred: You can add these routines to the ftp server or anywhere on (...) (29 years ago, 6-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Sonar
 
(...) Each diode loses 0.6v. The string of them drops the HB battery down from 9.6v to 6.0v, which is the specified operating voltage of the sonar unit. You can probably substitute 1N4001s. Fred (29 years ago, 6-Feb-98, to lugnet.robotics.handyboard)
 
  Programs
 
Hi All, I have just ordered a Handyboard and while i'm lerning IC i was wondering if the programs from the book Mobile Robots will work with the handyboard, my robot is configured similar to Rugwarrior,i.e. three bump an two IR proximity (...) (29 years ago, 6-Feb-98, to lugnet.robotics.handyboard)
 
  Making soun the beeper
 
I'm using imagecraft C , and want to make "beep" the beeper. what is the better way??? Germán Pablo Gentile. Genesys - Ingeniería en Sistemas. Data adquisition. Integral solutions for people identification and autorization. ggentile@cvtci.com.ar (29 years ago, 6-Feb-98, to lugnet.robotics.handyboard)
 
  Eprom Programmer info
 
Hi all, I have acquired an old Bytek Eprom/Pal programmer, Model S10 with and epm2 adapter. I have no manual. Does anyone out there have one, who might be able to photocopy a few pages from the manual. Bytek was of no help. Any help would be (...) (29 years ago, 6-Feb-98, to lugnet.robotics.handyboard)
 
  Re: analog input test
 
If the sensor headers look like this: live signal [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [X] +5v [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] ground [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] (...) (29 years ago, 7-Feb-98, to lugnet.robotics.handyboard)
 
  Re: encoder function
 
Tom, it seems that your routines measure frequency but Yoni wanted to count transitions. Yoni, the approach is similar to what Tom has done in that you must use the timer input channels to get high frequencies. In the TCTL2 register, set the input (...) (29 years ago, 7-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Rug Warrior Programs
 
you can use the mobile robot programs as long as you make appropriate changes for where you have mounted the sensors and motors. fred (29 years ago, 7-Feb-98, to lugnet.robotics.handyboard)
 
  IR schematics
 
Hello, I am currently designing an IR positioning system for our HB soccer robot project I think I have found schematics of an interesting IR beacon in Eagle format. Unfortunately I can't read Eagle schematics. Could so convert it for us in a JPG or (...) (29 years ago, 8-Feb-98, to lugnet.robotics.handyboard)
 
  68hc811
 
Hi, After 2 weeks of trying to reset/set the config reg. I have had no luck using any computer or software. I really need to get these chips to work and am willing to ship out to anyone who has experience in setting the conf reg. I have no other (...) (29 years ago, 8-Feb-98, to lugnet.robotics.handyboard)
 
  Re: 68hc811
 
I don't remember troubles trying to reset configs on the e2's, but it's possible i never tried to disable the eeprom. have you tried using motorola's pcbug utility? fred In your message you said: (...) (29 years ago, 9-Feb-98, to lugnet.robotics.handyboard)
 
  Pcbug config set.
 
(...) I have PCbug running and I can boot the hc811, after reading the motorola "Pink book" and the tec. docs I cant find anything on how to set the congif register. Does anyone know how to do this with the Pcbug software. (...) The strange this is (...) (29 years ago, 9-Feb-98, to lugnet.robotics.handyboard)
 
  IC and IR
 
This weekend, I got my HandyBoard running! Everything went fine, exept that the pice of paper which was glued on my battery pack turned out to be a theft-protection: it contained a magnetic layer, which caused short-circuit, but after solving that, (...) (29 years ago, 9-Feb-98, to lugnet.robotics.handyboard)
 
  Serial line interrupt
 
Hello all, I'm currently trying to communicate between the Handy Board and a PC (i486) using the existing serial line between the two. Sending data from the handy Board to the PC is no problem. An interrupt handler puts all incoming serial data into (...) (29 years ago, 9-Feb-98, to lugnet.robotics.handyboard)
 
  questions on IC
 
Hi all, These questions are probably pretty trivial, but please bear with me, as I have only been using IC for 2 days: 1. I was under the impression that the files I loaded onto my HB would remain there when I turn it off, I mean, the pcode does, (...) (29 years ago, 10-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Serial line interrupt
 
you could write an ICB driver that accepts the incoming serial char interrupt and buffers it up. other than that slowing down the PC is probably the best option. fred In your message you said: (...) if (...) ry (...) ng (...) (29 years ago, 11-Feb-98, to lugnet.robotics.handyboard)
 
  Proximity cards readers
 
Anybody has used that cards??? I want to comunicate my 68hc11 with that. Wich protocol use??? Anybody know one reader what read westinghouse cards??? thanks a lot.... Germán Pablo Gentile. Genesys - Ingeniería en Sistemas. Data adquisition. Integral (...) (29 years ago, 11-Feb-98, to lugnet.robotics.handyboard)
 
  RV: Proximity cards readers
 
-----Original Message----- De: Germán Gentile <ggentile@cvtci.com.ar> Para: Chuck McManis <cmcmanis@FreeGate.net>; Lista de Robótica General <robot-board@cmf.nrl.navy.mil>; Lista de Motorola- 6811 <Mot-68HC11-Apps@fre...tsps.com>; Lista de El_MICRO (...) (29 years ago, 11-Feb-98, to lugnet.robotics.handyboard)
 
  Fw: questions on IC
 
If there is ANYONE out there who can give me just a little guidance on these two issues, or at least the first and most important one, I would certainly appreciate hearing from them... an extended treatise isn't necessary, just a short answer will (...) (29 years ago, 11-Feb-98, to lugnet.robotics.handyboard)
 
  Sonar
 
I finished hooking up my 6500 sonar tonight, and it does nothing. Actually, the Handy Board's BATT light comes on, which indicates to me that there is a short some where along the lines. I checked my wiring and everything seems to be okay. I did (...) (29 years ago, 12-Feb-98, to lugnet.robotics.handyboard)
 
  Revision
 
Earlier I complained about the BATT light coming on, but then stupidity was pushed out of the way and I realized the battery was almost dead, so I plugged in the charger and put it on Zap. Sonar still does nothing, but the diodes got pretty warm. As (...) (29 years ago, 12-Feb-98, to lugnet.robotics.handyboard)
 
  'uploading' data?
 
Hi, I am programming a 6.270 board with IC and wondered if there was any way of 'uploading' data from the board back to my PC? or would the only way to get the data be to print it out on the screen.... Thanks, Ruth (29 years ago, 12-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Fw: questions on IC
 
re: #1, in a sense, the stuff you downloaded *is* there, but IC doesn't know how to access it until you re-download. So yes, each time you restart IC, you must re-download your project. re: #2. there are not good reporting tools for memory usage. i (...) (29 years ago, 12-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Sonar
 
Yes. It "clicks". I quess it's the part at the frequencies humans can hear. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the (...) (29 years ago, 12-Feb-98, to lugnet.robotics.handyboard)
 
  68HC11 modes
 
Return-Path: <roneill> Received: by thorung.eeng.dcu.ie (Linux Smail3.1.28.1 #5) id m0y2kzc-000FSwC; Wed, 11 Feb 98 22:51 GMT Message-Id: <m0y2kzc-000FSwC@tho...ng.dcu.ie> Date: Wed, 11 Feb 98 22:51 GMT From: roneill ("Richard O'Neill (...) (29 years ago, 12-Feb-98, to lugnet.robotics.handyboard)
 
  a scary story
 
Just an interesting (or perhaps not) story about what just happened to me this week while putting my Handy-Board together. I was on the section where you put on the digital input circuitry, and all was going well so far - it loads pcode_hb.s19, (...) (29 years ago, 12-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Sonar
 
Yup. I loaded the sonar.c file and ran the sonar_display() routine. It just displays values that make no sense. The sonar doesn't click and the diodes get hot. After recieveing some mail from other, I have come to the conclusion that the diodes are (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  encoders
 
Hello all, I am attempting to use the shaft encoder routines but am having trouble.When I try to load the file fencoder0.icb I get a message that ic cannot find the file.Any hints? Also I would like to know whether these routines count off one edge (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Interrupt for serial data
 
I've decided to write an interrupt routine for the handling of serial data on the Handy Board. An example of an interrupt routine is given in the Handy Board technical reference. This works like a charm. I've modified it to use the SCI interrupt. (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  re: 9v lego motors
 
Lego motors are OK ptrformance wise (if youre talking about small robots), but the cost is really bad. What I would recommend is taking surplus motors and superglueing them together to lego bricks. Especially for photsensors and switches. phil (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Lego 9V motors work well?
 
What has been people's experience in using the Lego 9V motors with the Handyboard? I know they're overpriced, but they are easy to use... We've used small RC car motors etc. in our Lego robot course in past years, but some students have been looking (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Lego 9V motors work well?
 
[Greg Starr] spake unto the ether: (...) Performance-wise, they are okay (i.e., they are powerful enough). I don't like the short axle they have on them, though (compared to e.g. a Mabuchi motor with a LEGO 2x drilled axle Super-Glued onto the motor (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  using relays to run a motor
 
Hi Ive elected to use 2 relays to run a motor. Im going to put one motor on with the power coming in 'straight' and the other one in reverse of the first one: [RELAY 1] [RELAY 2] ++ -- -- ++ (power is inverted) |--------| |---...---| | \_______ | (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Lego 9V motors work well?
 
LEGO motors work great. Fred (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Lego 9V motors work well?
 
Hi Greg, I have been using LEGO 9v motors for a few years and I am very pleased with the results. I run freshman and sophomore engineering design and computer science courses using LEGO kits and HB's. The motors are well worth the price if you are (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Sonar
 
In article <v03020900b10948ab85...2.4.189]>, Michael S. Reiling <macman@inreach.com> writes (...) Did you remember to solder the C7 capacitor in? ___ IAN | |__ _______ ______ ___ ______ ___ ___ | _ \| _ | ___| | | _____|\ \/ / | |_ ) | _ | |_--- (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Lego 9V motors work well?
 
In article <v03007807b10a2f11bb...4.217.7]>, Greg Starr <starr@unm.edu> writes (...) I've used lego motors and have found them much better than other motors i have tried for torque. The ease of integrating them into lego buggies is obviously a major (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: 'uploading' data?
 
(...) Yes, this is very possible, and I've done a fair amount of work for various experiments where I needed to get data back from the board. First, you should check out (URL) the routines that the 6.270 and Handy Board that let you disable the (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Interrupt for serial data
 
Jan-Sipke, You're really pretty far away from having this work. It's not just a matter of redirecting the serial interrupt; when you get there, you have to: * store incoming character in a buffer * advance the buffer pointer * check the buffer for (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Interrupt for serial data
 
(...) Sipke obviously realizes that more work is needed, and justs want to get to step 1 first by recognizing the interrupt. That is exactly what I would do too. I've been thinking about writing an interrupt-driven serial receive routine too, but (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: 9v lego motors
 
Everyone is complaining about the price of LEGO motors. There is a new product, a gear reduction motor, that is a great value. It is a super efficient DC motor with a built in gearbox that can be used for direct drive, or with one stage of gear (...) (29 years ago, 13-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Sonar
 
If the diodes are getting hot, it does indicate a short. Fred In your message you said: (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
 
  public apology
 
Yes -- I didn't think very hard and in retrospect it's fairly evident that Jan-Sipke's code is just the starting step. Sorry for being such a blunderhead. (Jan-Sipke and I have been exchanging some private messages and I think he's closing in on a (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
 
  Re: encoders
 
(...) trouble.When I try to load the file fencoder0.icb I get a message that ic cannot find the file.Any hints? (...) pulse or what dictates how the count is incremented. I think the file is named fencdr0.icb by default (not fencoder.icb). Maybe (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
 
  RE: encoders
 
-----Original Message----- From: Will Bain [SMTP:willbain@cs.umt.edu] Sent: Saturday, 14 February 1998 12:50 To: handyboard@media.mit.edu Subject: Re: encoders (...) trouble.When I try to load the file fencoder0.icb I get a message that ic cannot (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
 
  RE: encoders
 
(...) In my experience, it doesn't matter how slow the pulse is. The count is increased each time the analog port value crosses outside of the middle range defined by the two threshold values as shown below (please note that you'll need to view this (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
 
  Re: 68HC11 modes
 
The handyboard has to stay in special test mode so that it can switch into and out of 'single chip' mode at will. This is necessary to operate the LCD (which uses either a clever or gross hack depending on your taste). If you are writing code using (...) (29 years ago, 14-Feb-98, to lugnet.robotics.handyboard)
 
  pa7 9600 serial output
 
Hi, I'm trying to interface the FerretTronics Servo Controller Chip FT639, to the handyboard using PA7. How can i modify the pa7_9600.asm file to transmit at 2400 baud? thanks, phet (29 years ago, 15-Feb-98, to lugnet.robotics.handyboard)
 
  Infrared port on the HB is not working: need help!
 
hello! I pulled out my HB today and rtied playing around with the IR port. it does not work for some reasons. I checked the remotes: they are still transmitting! Here are the steps I took: am I missing a step? 1. loaded sony-ir.icb 2. sony_init(1); (...) (29 years ago, 15-Feb-98, to lugnet.robotics.handyboard)
 
  Speech Synthesizers
 
I am wanting to add speech to the Handy Board. I am currently looking at interfacing a SPO256-AL2 speech synthesizer chip and have a very limited schematic that came with the chip many years ago. Does anyone have a nice set of schematics for doing (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  L293D
 
where does the pwm go? ...the "cs" or the "in" pins? ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of Science and (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  Measuring PW
 
Has anyone been able to successfully use Thomas Hauri's PW measuring routines?? For some reason whenever I try to load them they crash my IC. Any thoughts?? Joshua Stark j-stark@uiuc.edu Aspiring Computer Engineering Major (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  using the MC34064 LVI
 
Hello, This is a warning for anyone considering using the Motorola MC34064 to replace the DS1233. I have just built a couple handyboards and I had some problems getting them working. I finally tracked the problem done to the LVI. I used the MC34064 (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  Re: pa7 9600 serial output
 
(...) You have to re-write the bit_delay loop to take up four times as much time. Just multiply the delay count value by four, e.g., "LDAB #148". Fred (following is the 9600 code.) * take up 0.1042 millisecs * 208 cycles bit_delay LDAB #37 bit_loop (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  Digital input cct
 
Hi there, I'm in the middle of building a handyboard and I'm having a lot of problems. I'm on part 7.2 (Digital Input cct) and the testdigitals(); function in hbtest.c doesn't respond to the start button. All the chips and RP1 are installed properly (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Interrupt for serial data
 
I have been using very successfully for two months now, the code in the attached zip file. It has Interrupt Driven Transmit & Receive functions, both are buffered. I found the code easy to adapt for my specific task. Messages can be "Canned", Fixed, (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Interrupt for serial data
 
I have been using very successfully for two months now, the code in the attached zip file. It has Interrupt Driven Transmit & Receive functions, both are buffered. I found the code easy to adapt for my specific task. Messages can be "Canned", Fixed, (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  Expanding the memory of the handyboard
 
A number of students that used the handyboard in our Mechatronics competition needed substantially more memory than the 16,320 bytes currently available. What options are there to add memory to the handyboard? Thanks to everyone who contributes to (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  bouncing ball
 
Hey! Im a realitivly clueless High school guy. Our Adventures in Supercomputing group is making a mobile robot using a handyboard and 3 or 4 infared sensors. Is tyhe bouncey ball method a good one for having a rover permeate a halled area? the (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Expanding the memory of the handyboard
 
Dear Kevin, Please forgive this non-answering of your question, but I am curious as to what kinds of hardware projects/software objectives were your students working on when they ran out of 'hc11 memory, and how did they deal with this circumstance? (...) (29 years ago, 16-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Lego 9V motors work well?
 
I'm curious how you went about securing the motors to your robots. I picked up a couple yesterday, and they do seem to be very good quality motors, but just sticking them on "the LEGO way" doesn't work too well. They keep ripping themselves loose (...) (29 years ago, 17-Feb-98, to lugnet.robotics.handyboard)
 
  RE: Expanding the memory of the handyboard
 
Dear Fred, The Mechatronics class competition was to build autonomous miniature forklifts that would navigate a complex course. In the course, the forklifts had to identify, pick up, and deliver three. The path that the forklifts had to negotiate (...) (29 years ago, 17-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Sonar
 
Sure did. I used a ceramic disk capacitor... Hope that was okay to use. I just can't find what the problem is with the ranging board. For all I know, it has never worked. This is my first attempt at using it. There really isn't a whole lot to the (...) (29 years ago, 17-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Lego 9V motors work well?
 
(...) The Lego motors are sized such that they can be "pinned" to the frame of a Lego robot easily. With a horizontal beam beneath the motor and another across the top, a pair of six-unit beams can be pinned vertically to the horizontal beams using (...) (29 years ago, 17-Feb-98, to lugnet.robotics.handyboard)
 
  IC 3.x Reg Code
 
Does anyone have a temp 3 week reg code for IC 3.x that I could use?? Im having problems loading the frequency measuring routinues provided on this mailing list and I believe it might be because I'm still using IC 2.8 and the routines have been (...) (29 years ago, 17-Feb-98, to lugnet.robotics.handyboard)
 
  1998 MIT LEGO Robot Design Contest videos on-line
 
Hi everyone, Quicktime and RealVideos of this year's contest highlights can be had at (URL) (29 years ago, 17-Feb-98, to lugnet.robotics.handyboard)
 
  Re: IC 3.x Reg Code
 
Newtonlabs will give you one if you ask them. ic@newtonlabs.com (...) (29 years ago, 17-Feb-98, to lugnet.robotics.handyboard)
 
  (no subject)
 
I'm just wondering, is the "charge" LED supposed to come on on the I/C board when you're running code on the Handy-Board? I don't think it should, but I'm not sure. Thanks, Rob O' Neill (29 years ago, 17-Feb-98, to lugnet.robotics.handyboard)
 
  (no subject)
 
assuming the battery is not yet connected (which would be the case of you're building the HB and following the directions), the charge LED means that the HB is drawing some current. fred In your message you said: (...) (29 years ago, 17-Feb-98, to lugnet.robotics.handyboard)
 
  Pulsewidth Functions
 
Does anyone know if you need IC 3.x to run the pulsewidth measuring functions provided by Thomas Hauri?? Joshua Stark j-stark@uiuc.edu Aspiring Computer Engineering Major (29 years ago, 18-Feb-98, to lugnet.robotics.handyboard)
 
  Thanks Fred et al...
 
My first scratch-built HamdyBoard has passed all of it's tests and is up and running. I've only been looking for something like this for about twelve years, so I'm REAL happy. I especially appreciate the emphasis on both hardware and software (...) (29 years ago, 18-Feb-98, to lugnet.robotics.handyboard)
 
  Re: Expanding the memory of the handyboard
 
(...) How did the board read the barcode label? What equipment/algorithm was used? I've been screwing around with a train, and haven't really had any luck with reading a barcode from the track as it passes over. --- Chris Osborn FozzTexx Enterprises (...) (29 years ago, 18-Feb-98, to lugnet.robotics.handyboard)
 
  RE: Expanding the memory of the handyboard
 
We used OEM barcode reader (IS4120-41 scanner decode engine) from Metrologic Instruments, Inc.. The output of this reader is the barcode ASCII format transmitted across an RS232 line. We read this with the handy board's RS232 serial port. You can (...) (29 years ago, 19-Feb-98, to lugnet.robotics.handyboard)
 
  IR receiver hookup
 
Hi all, What is the procedure for hooking up the Radio Shack GP1U52X IR receiver to the digital inputs of the Handyboard?, do I need a transistor between the units output an the HBs digital input?. Thanks, Clancy. (29 years ago, 19-Feb-98, to lugnet.robotics.handyboard)
 
  Download troubles
 
Hello I´m a beginner. I have problems download pccode in my HB. I´ve a Mac G3 and I use Init board HB 7.2 modem & 6811 Downloader. I,ve check connections, batteries and the board is in download mode. Bat/pwr LEDs light on (1/3 second) and turn off. (...) (29 years ago, 19-Feb-98, to lugnet.robotics.handyboard)
 
  downloaded
 
Finaly I have got to download pcload in my HB!!!! You are rigth, I´ve load in a Macintosh CI. Now with IC system in the board, I can work in my Mac G3. ?:-( . Fred, thanks for all. I am trying to buy the key password for IC 3.1, but is impossible, (...) (29 years ago, 19-Feb-98, to lugnet.robotics.handyboard)
 
  Expansion board test code
 
Duncan, The expansion board test code you sent worked quite well, It was very useful in testing and trouble shooting my expansion board. Thanks, Clancy (29 years ago, 19-Feb-98, to lugnet.robotics.handyboard)
 
  RE: downloaded
 
I have the same problem too. I sent thousands of e-mail to newton labs without any answer. Could someone help ? Thanks. (...) (29 years ago, 20-Feb-98, to lugnet.robotics.handyboard)
 
  Re: downloaded
 
(...) Laurent -- just to be clear -- your problem is that you can't bootstrap your board from a G3 Mac, but after you do get it booted, everything's OK? Fred (29 years ago, 20-Feb-98, to lugnet.robotics.handyboard)
 
  IC 3.2 announcement
 
After seeing some of the recent e-mail to this list, I realize that we should send out the following announcement to the Handyboard list. IC 3.2 for Windows fixes the problems that a percentage of folks reported about pcode download problems. (...) (29 years ago, 20-Feb-98, to lugnet.robotics.handyboard)
 
  Ordering IC
 
Dear Laurent and German, I wish to publicly apologize for Newton Lab's slowness of response to your messages of last fall. You should know that the employee in charge of handling IC sales and support during that time is no longer with the company. (...) (29 years ago, 20-Feb-98, to lugnet.robotics.handyboard)
 
  Re: IC 3.2 announcement
 
On a related note ... Sometime ago, someone(???) mentioned that he would attempt to build the new motor routines into IC3.1. Would this by any chance be already in IC3.2? Jun Nolasco nolasco@inx.net (...) (29 years ago, 21-Feb-98, to lugnet.robotics.handyboard)
 
  Re: RJ11 cable
 
please see the FAQ on this, look for the entry on "help my interface board is smoking and R11 is turning black!" (that's what happens if you get it wrong) fred (...) (29 years ago, 22-Feb-98, to lugnet.robotics.handyboard)
 
  Please unsubscribe
 
Hi Please unsubscribe me from this list regards Bruce (29 years ago, 23-Feb-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR