To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.robotics.handyboardOpen lugnet.robotics.handyboard in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / Handy Board / 3230
3229  |  3231
Subject: 
Re: analog input test
Newsgroups: 
lugnet.robotics.handyboard
Date: 
Sat, 7 Feb 1998 14:01:34 GMT
Original-From: 
Fred G. Martin <FREDM@MEDIA.saynotospamMIT.EDU>
Viewed: 
5913 times
  
If the sensor headers look like this:

live signal [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ]    [ ] [ ] [ ] [ ] [ ] [ ] [X]

+5v         [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ]    [ ] [ ] [ ] [ ] [ ] [ ] [ ]
ground      [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ] [ ]    [ ] [ ] [ ] [ ] [ ] [ ] [X]
sensor#      15  14  13  12  11  10  9   8   7      6   5   4   3   2   1   0

Then for sensor 0, you use the header pins marked as [X].

If you are sure you have a 10K resistor, and you are using the correct
pins, and you are getting a reading of 5 or 6 (not 40), then this
suggests that the resistor pack value is wrong.  You should have a 47K
resistor pack.  If a 10K resistor yields a value of 5 or 6, you might
have a 470K resistor pack soldered down between the +5v and signal
rows.

re: DL, thanks for your observations.  I'll take note of it.

Fred

In your message you said:
> Fred;
> 
> I am at the testanalogs portion of the assembly process.  All has gone
> well up until this point.    The knob varies between 0 and 255 as
> expected and the seven numbers all come up either 254 or 255 when I
> press the START button.  However I am confused as to which headers I
> should insert the 10k resistor as well as the output I receive depending
> on which header pairs I use.  Are the two outer most headers the two
> that are side by side at the edge of the board?  If I insert the
> resistor in these the readings all stay 254 or 255.  Or are the two
> outermost headers those which are separated by the in line resistor and
> the other header, (i.e. the header closest to the edge and the header
> closest to the plcc socket)?  When I insert the resistor in these
> headers the number changes to 5 or 6 not 45.  The voltage at pins 51 and
> 52 check out and I seem to have continuity.
> 
> By the way, I attempted to download Pcode using hbdl and dlm using a 233
> Pentium II, a 166 Pentium, and a 386 all without success.  However, I
> was successful on the first try on the Pentium II using dl in a DOS
> window.  Perhaps this should be recommended as the default down loader
> for PC's.
> 
> Love your board;)
> 
> Pat Benoy
> 
> 



Message is in Reply To:
  analog input test
 
Fred; I am at the testanalogs portion of the assembly process. All has gone well up until this point. The knob varies between 0 and 255 as expected and the seven numbers all come up either 254 or 255 when I press the START button. However I am (...) (29 years ago, 5-Feb-98, to lugnet.robotics.handyboard)

2 Messages in This Thread:

Entire Thread on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact
    

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR