To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *3701 (+100)
  SONAR
 
Does anybody have a simple piece of code that just illustrates how to use the sonar modules? Ive looked all over and cant find anything instructional on the web. Thanks, Richard (29 years ago, 26-Apr-98, to lugnet.robotics.handyboard)
 
  Trouble with Tom Brusehaver's Vector 2X routines
 
Hi! Is there anybody else having trouble running his V2X with Tom Brusehaver's routines? With my own very crude IC-routines I get it working, but I'd like to use Tom's, because they are much more comfortable. Any help appreciated! Alf (29 years ago, 27-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Trouble with Tom Brusehaver's Vector 2X routines
 
Alf, Try loading compass.icb first then compass.c. at the prompt type v2x(); ---...--- (...) (29 years ago, 27-Apr-98, to lugnet.robotics.handyboard)
 
  HB weight
 
does anyone know the weight of a handy board? thanks, -Brian (29 years ago, 27-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Help!! Polaroid problem!!!
 
Note that sonar in air is susceptible to the same environmental issues as sonar anywhere. In particular it is susceptible to changes in temperature and changes in air pressure. Both of which create a boundary layer that reflects some of the energy. (...) (29 years ago, 28-Apr-98, to lugnet.robotics.handyboard)
 
  IR Transmit
 
I am trying to get two handyboards to exchange data via the IR. I have tried code from the Dave Negro and Pete McCann code, but I still cannot get reliable data transmission at any range. Summary of situation: REC80-IR.icb: Reliable reception of (...) (29 years ago, 28-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Handy board help
 
(...) There is a little strip of four pins for external battery power and are available with the standard battery pack installed. Two of these are battery positive, two are at ground. Shorting them out is a good way to let the smoke genie loose. (29 years ago, 28-Apr-98, to lugnet.robotics.handyboard)
 
  More Polaroid problems!
 
Well, everything seemed ok, but now (we are in a crunch again, the final presentation is Friday!) there is another problem. We seem to be getting some erroneous distances and I think I know why. The echo signal is pretty noisy, so my question is, (...) (29 years ago, 29-Apr-98, to lugnet.robotics.handyboard)
 
  Smooth PWM with IC 3.2
 
I know this is an old thread but I am just now getting to the point where I can finally start programming. I am using IC 3.2 and the expansion board. I downloaded the smooth PWM routines from Newton Labs but I get errors when I load them into the (...) (29 years ago, 29-Apr-98, to lugnet.robotics.handyboard)
 
  memory expansion
 
Hello, Has anyone figured out a GOOD way to expand the memory on the Handy Board? I would like to try using a 32 pin simm (I have sizes ranging from 256k to 4M) to store mappings (distance and turns) created by the initial "adventure" it takes of (...) (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  memory expansion
 
Hello, Has anyone figured out a GOOD way to expand the memory on the Handy Board? I would like to try using a 32 pin simm (I have sizes ranging from 256k to 4M) to store mappings (distance and turns) created by the initial "adventure" it takes of (...) (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  Quick prototyping technologies
 
I am looking for good methods for quick prototyping and would appreciate all suggestions. In Mobile Robots by Joseph L. Jones and Anita M Flynn, they suggest using Scotchflex by 3M and Speedwire by Bicc-Vero company as two good alternatives to using (...) (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  V2x AND Polaroid Sonar
 
Hello again, Has anyone been able to wire the V2x compass and the Polaroid sonar device both to the HandyBoard and, if so, how was it done? Thanks, Scott sherman@plains.nodak.edu CSG ITS NDSU (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  Schematic Question
 
I have been looking at the schematic for the handyboard and the RS232/Charger board. I noticed something that seems wrong. But how could it since this has been out for some time? Power goes out pin 4 of J10 on the Charger board and pin 4 on (...) (29 years ago, 30-Apr-98, to lugnet.robotics.handyboard)
 
  Re: Schematic Question
 
You're missing the fact that the telephone style RJ-11 cable is an inverting cable. see page 11 of 16 of the Handyboard FAQ at (URL) a discussion and diagram of this (and the consequences of using the wrong cable!). -patrick ---...--- (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  Re: Quick prototyping technologies
 
(...) I recently contacted Vero aboout Speedwire. The product is indeed discontinued and they have no old stock in the UK. However, speedwire pins are, apparently made for them by someone else. Unfortunately they could not find out (at that time) (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  Alternate Part - DB101-ND
 
I could not get the bridge rect from digikey for the DB101-ND. Does anyone know of an equivelant part(s) that I might get somewhere else? Otherwise I'll have to wire some diodes up for this. -- ---...--- ipscone@halcyon.com Shoot-To-Win! Protect the (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  SPI Interface
 
Hi, is there anywhere a function for IC 3.2 to communicate via the SPI interface with another controller ? Thanks in advance. Erwin (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  V2x and sonar
 
Hi, Wouldn't it be possible to wire them both to the same input port and turn on the one that you want information from and turn the other off? For example, the polaroid sonar data states that you can control turning on and off the device, so you (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  loading files
 
Hi, I am having problems loading my files onto handyboard. Whenever I try to load a file, it says ; function analog undefined function motor undefined It used to work fine before and I don't know why I am having this problem all of sudden. Can (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  Re: V2x and sonar
 
If you only use one motor controller IC you can use the 16 pin socket of the second motor control to get 4 more outputs. Then you can connect the INIT and BINH to these and have Port D control your V2x compass. All you have to do is modify your (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  Schematic drawing - freeware ???
 
Hi, Has anyone come across a freeware schematic drawing package for Windows PC? Any help would be much appreciated. thanks in advance. Les (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  Re: loading files
 
It suggests you are not loading lib_hb.c on start up. If you type list files at the IC command line you should see this file listed, as well as any others. If it isn't there, check your lib_hb.lis file and be sure lib_hb.c is listed in it. (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  RE: Schematic drawing - freeware ???
 
I came across this web page today. It may have what you are looking for. (URL) Message----- From: Les Novotny [mailto:les@progress...tions.com] Sent: Friday, May 01, 1998 11:03 AM To: handyboard@media.mit.edu Subject: Schematic drawing - freeware (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  Re: Schematic drawing - freeware ???
 
Try to look up MicroSim ...or something like that name. It has a crippled evaluation package that may suit your needs. I think the company is the developer of psplice. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  Max232CPE Substitutions
 
I used a Max202 in place of the Max232. I installed it with the 10uF caps. Since the 202 can be used with .1 and I already installed the 10uF ones. I decided to switch it for a 232. The 202 checked out (V wise) like the installation instructruction (...) (29 years ago, 1-May-98, to lugnet.robotics.handyboard)
 
  Schematic & PCB freeware
 
Ivex has a very good schematic and PCB layout demo at www.ivex.com ,the only difference between the demo an the full version is the demo is limited to 100 pads. (29 years ago, 2-May-98, to lugnet.robotics.handyboard)
 
  DS1233 Monitor Chip
 
I cannot locate a DS1233 chip. I have tired DigiKey, Jameco, Mouser, Active. What is a good source for this part? I have an MC34064. Looks similiar except that it has no 350mSec delay and a different pinout. Has anyone tried this chip without any (...) (29 years ago, 2-May-98, to lugnet.robotics.handyboard)
 
  controlling a DC motor
 
Hello, i am currently trying to control a DC motor's motion (direction, speed, etc). Besides using a motor driver chip such as L293D, what else can i do to control the motor's motion?? Say, is there a method which can control the motor by totally (...) (29 years ago, 2-May-98, to lugnet.robotics.handyboard)
 
  Testing with PCBUG11
 
I have assembled the HandyBoard up to the point of adding the SRAM. I am still waiting for my SRAM to arrive. But, I want to check out as much as possible. Every step checked out fine to this point. I have two options at this point. I have an 6264 (...) (29 years ago, 2-May-98, to lugnet.robotics.handyboard)
 
  Re: Testing with PCBUG11 - Getting Close
 
My problem turned out to be with Win 95. If I boot to DOS the PCBUG11 program works fine. It fails to work when working from a DOS window. I can now communicate with the MCU so my RS232 must be fine. When working from the command line in PCBUG, I (...) (29 years ago, 2-May-98, to lugnet.robotics.handyboard)
 
  6.270 board
 
What is 6.270? Where did this number come from? ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of Science and Art (...) (29 years ago, 2-May-98, to lugnet.robotics.handyboard)
 
  Connections
 
Please forgive this probably silly question; as a software person I only dabble in hardware as a hobby: I want to make my own little expansion board and it requires signals from the expansion connectors of the HandyBoard. In particular I want to run (...) (29 years ago, 2-May-98, to lugnet.robotics.handyboard)
 
  MODB - How Is Expanded Mode Entered
 
If MODB pin is always grounded, how does the MCU get into expanded mode to access the 32K SRAM? The data sheet shows MODB HIGH to enter expanded mode. It show MODB LOW to enter single chip mode. What am I missing? -- ---...--- ipscone@halcyon.com (...) (29 years ago, 2-May-98, to lugnet.robotics.handyboard)
 
  Handy Board problem
 
I was wondering if anyone knows where I could purchase the Sharp Is1U60 IR detector. I have looked for it, however none of the distributors I have checked with even carry it. I tried Digikey, Mouser Electronics, JDR, Jameco, BG Micro, and others. (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  Controlling a DC motor 2
 
Hi again, I think i should change my previous question to the following. Is there any alternatives to control a DC motor motion (speed, direction etc) without using a motor driver? how? please explain briefly. Thank you for your replies. (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  My LCD driver
 
Attached to this message is the LCD driver I wrote for the Handyboard written using ICC11. Feel free to use it. Some notes on it: The driver is designed to operate asynchronously. This is because the LCD can take several milliseconds to complete its (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  whoops, wrong test program
 
Attached to this message is the test program and S19 file for the LCD code. --Chuck (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  IC communication problem
 
Hello, Lately I am having problems communicating with the handyboard after it is reset. I can download the pcode_hb.s19 file using hbdl.exe downloader. When the Handyboard is reset by toggling the power switch, the following is observed. 1st symptom (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  Polarity of PowerJack from HB und Charger Board
 
Hi I am wondering about the Polarity of the Power Jack at the Handyboard and the charger board. At the HB the Pin in the middle is ground. At the charger board the outside Ring is ground.Can anybody tell me why it is different ? Thanks (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  recharging a battery the right way
 
hello I have a 6v 2.0amp battery. Its a lead acid battery. What is the right way to recharge it? The reason I ask is because I had a 12v 7amp battery from the same manyfacturer. I charged it using a car battery charger at the lowest setting (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  LCD Addressing - & - Expanded Mode
 
Two questions: 1) I'm having a little trouble figuring out how the LCD is addressed. It uses A8 and A8 but also is clocked from Port A. Can someone explain how to properly address the LCD using ASM? 2) The Mode B pin is always grounded. How does the (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  Controlling a DC motor 3
 
Thank your for all your replies, I understand what 's going on now Another question about the motor driver is: Q) The PWM is a sequence of pulses switching on & off the H-Bridge. But what should be the rate of PWM? 1000Hz?? why? what does the rate (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  Cannot download pcode on a Mac G3
 
Hello everyone, I've been having a problem downloading pcode to a handyboard or rugwarrior board from my Mac G3 (266 Mhz desktop model). When I try to download the bootstrap code, it reports that the bootstrap failed after 000 bytes, etc.. etc... (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  Re: Cannot download pcode on a Mac G3
 
Paul -- have you tried 6811 Downloader? Any luck with that? looks like Randy and I will both need to get our hands on a G3 to debug our code :-) Fred In your message you said: (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  Re: Polarity of PowerJack from HB und Charger Board
 
on the interface/charger, since there's a bridge rectifier immediately normalizing the input jack voltage -- regardless of polarity -- it kind of doesn't matter which polarity you use. there is a discrepancy between the int/charger schematic and (...) (29 years ago, 3-May-98, to lugnet.robotics.handyboard)
 
  Re: LCD Addressing - & - Expanded Mode
 
(...) You can only run the LCD when in single chip mode. (...) This leaves the chip in 'special test mode' that lets you go into and out of expanded mode by writing the config register. --Chuck (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: Controlling a DC motor 3
 
(...) Within limits, the rate doesn't matter much. What matters is the ratio of off time to on time (i.e., the duty cycle). Probably, you could change the frequency by an order of magnitude either way and get about the same results. --Will , , __@_/ (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Micromouse speed
 
Hi, does anyone know how fast should a micromouse move? and the other question is, will the 6811/handyboard have enough capability (address space) for maze solving? If not, what should I need? extra memory or 32bits processor? Thank you for any (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: DS1233 Monitor Chip
 
(...) I use an MC34064 on a 68hc11, and have never had any problem with it. Philippe Guermeur guermeur@ensta.fr (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: LCD Addressing - & - Expanded Mode
 
So, this still doesn't help me figure out how to address the LCD. It has A8 and A9 connected along with a CLK from Port A. Does this mean that the LCD is NOT memory mapped? Do I first have to write to Port B then write to Port A, to clock it. This (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: LCD Addressing - & - Expanded Mode
 
Wierd: Anyway I have some kind of problem with the handyboard. All steps up to the testing of the LCD went fine. When I plugged in the LCD and turned it on, it lights up (one line) bright not dim. I tried to download the pcode_hb.s19 with config set (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: LCD Addressing - & - Expanded Mode
 
I found the driver you sent earlier. Thanks. BTW, I found out that my LCD is good but I still have a problem. It appears that I cannot change my CONFIG reg. Maybe because it is an 811E2; don't know. Should be able to however. Since the program was (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: Handy Board problem
 
I got mine from FutureActive. I don't remember what the cost was and I don't remember what else I got from them, but it was more than just that. I think I placed about 2 orders with them. I would much rather deal with Mouser and Digikey. If you have (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: Schematic drawing - freeware ???
 
Hi Les, i´m using a nice drawing programm (TARGET 2001). In germany we can get a "lite" Version of a big-drawing programm it´ easy to use and it works great, but it is in german. If you are interested, send me a mail tschau bernd (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: Cannot download pcode on a Mac G3
 
Hi Paul, This is the first time we've heard of such a problem with IC 3.1 on the Mac G3. Can you verify that it is the case that pcode download works fine for you from other Macintoshes? -- Randy ---...--- (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: Cannot download pcode on a Mac G3
 
(...) Yes. Using the same set of boards, I can download pcode using IC 3.1 as well as IC 2.xxx from my old macintosh Centris 650 as well as from Performa 6100. -Paul (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  RE: Connections
 
Hmm... I had the same problem and made an only mildly inelegant kludge with straight and right-angle headers. How much do you enjoy soldering? Seriously, does anyone know of any single-row intraconnectors? Brett Anthony Research Technician School of (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: dc motor blues
 
Hi All; Along the same lines, I would LOVE to control my motors so they run at constant speed under varying load. I know that it's theoretically possible to sense the RPM of a PM DC motor by tracking the drive voltage as the commutator makes and (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: LCD Addressing - & - Expanded Mode
 
From the driver code I recently sent out: * LCD Connections on the Handyboard * PORTB bit 0 - R/W * PORTB bit 1 - RS (Register Select, 0 = instruction) * PORTC 8 bits of Data * PORTA bit 4 - E clock (...) That is correct, the LCD is NOT memory (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Working with a different compiler 2
 
Howdy All, I am in a happy mood today. I finally got to the 'hello world' stage. All I had to do was count the number of interrupts, * 2 (16 bit addresses), subtract this from BFFF which is the reset vector and thus supply BFD6 to my linker to start (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: Motor Drivers in 7000 - 7fff
 
Jaron, (...) This was done (obviously) to save extra decoding circuitry needed on the board. That is, if the handy board needed to assign (say) 7000 as the motor then sixteen address lines need to be decoded (binary 0111 000 000 000). Yet with the (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Hardware Questions
 
Recently, many of you have had pretty specific hardware-related questions. The best thing to do is to read Appendix B of the MIT 6.270 Robot Builder's Guide (Appendix A of the new 1998 Course Notes). This appendix contains a complete description of (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: Cannot download pcode on a Mac G3
 
I have a 266 G3 minitower, and I have the identical problem. The only way to solve this is to let IC die, not reset the HB and then run IC again. It complains to can't talk to the HB, and then I reset the HB and all works fine. Kinda odd, but it (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  **handyboard**
 
hello, i was wondering if anyone can help me.i dont own a handyboard yet, how do you program it, i am worried that it is very compicated to do. please if you could send me some simple code say to move both drive motors fwd, how would you do it? i (...) (29 years ago, 4-May-98, to lugnet.robotics.handyboard)
 
  Re: Controlling a DC motor 3
 
(...) Actually, the frequency is somewhat important. The faster you switch, the more power will be lost to the switching of the power transistors and the filtering effect provided by the inductance of the motor. At the other extreme, frequencies (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  how do i get info on where to buy a handyboard?
 
hi i am lookin for a handyboard, i saw one at trinity college it came with batt charger prgrm cable dc motors sensors etc... where do i get one a phne # or e-mail address etc... thanks -mike (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: LCD Addressing
 
Mike, Chuck McManis may have answered your request, but in case you still want sample code I am attaching an example code that prints to the HandyBoard display. (The code forms part of the Handy Board buffalo I had developed). I had trouble getting (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: how do i get info on where to buy a handyboard?
 
Mike, (...) The best place for all information about the handy board, including the places to buy, is the Handy Board Home page. (URL) get directly to the page on where to buy them, then go here: (URL) (at the Uni) purchased ours from Patrick Hui, (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: **handyboard**
 
You can write "Interactive C" (IC) programs on a PC/Mac and download it into the HB. IC is like C but alot less complicated. If you know C, it is pretty simple. If you don't know C, it is just simple. You can also write Assembler which is a little (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: how do i get info on where to buy a handyboard?
 
Look up "Handy Board" on the internet. It will be the first hit on the search usually. ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: recharging a battery the right way
 
you should charge a lead acid battery which is between 10% and 90% charged at a rate of Capacity/10. In this case the rate would be 0.2 amps. when the battery is either almost charged (>90% charged) or almost depleted (<10% charged) the rate shoud (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  HandyBoard in Germany
 
Hello Community, I would like to enter the "World of HandyBoard" and I'm searching for a Distributor in Germany (or some people who know how to get one in Germany). I would buy it in every state: ready-made, kit and PCB only. Is there a community of (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: how do i get info on where to buy a handyboard?
 
Go to Handy Board WEB page and look under "Get One". You will see all kind of info of how to get one including bare PC board and component vendors. Here is the URL: (URL) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  L293d
 
Hi everybody Can someone tell me which websites I can order the motor driver chips, L293d? Thank you. (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: HandyBoard in Germany
 
Hallo Kai, da ich ebenfalls aus Deutschland komme, habe ich vor einiger Zeit das gleiche Problem gehabt. In Deutschland wird nach meinem Wissen lediglich das Rug-Warrior Bord vertreiben (über Joker-Robotics). Ich habe mein HB in den Staten gekauft, (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  FW: Just in case
 
(...) [Lewis] Thanks (...) Shareware VB Add-Ins (Written By Me) Available On My HomePage www : (URL) (...) ICQ: 11508290 Work: (URL) lewis.cornick@silversands.co.uk (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  (no subject)
 
Help: We have had five boards go bad after charging of the battery. These boards passed all of the tests and functioned perfectly. However after the batteries were first discharged then recharged we get nothing on the screen. pcode appears to load (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  FW: FW: Just in case - it's a hoax
 
Sorry, should of checked first..... (...) Shareware VB Add-Ins (Written By Me) Available On My HomePage www : (URL) (...) ICQ: 11508290 Work: (URL) lewis.cornick@silversands.co.uk (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  *low voltage sensing*
 
hi i need to know if the handyboard can sense low-voltage and what the program would look like in c or some kind of basic? thanks -mike (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: *low voltage sensing*
 
if(analog(0) < 240) { blah blah blah } analog(0) is the analog sensor 0 on the HB and 240 is like 4.7V 240/255*5.0V = 4.7V ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  New for 98, Finger Board II - Redesigned
 
New features on Finger Board II: Improved layout and better parts spacing. No extraction tool required for processor removal. Improved silkscreen. Jumper selectable reset address. Reset vector can be located at 0xFFFE,0xFFFF or 0xBFFE,0xBFFF. Now (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  how do I build my own pcode?
 
Title says it really. I am using both IC2.8something and IC3.2. I would like to make some small changes to the pcode for these to allow other LCDs and so on. (one goal would be to do without the LCD if I wanted to) I would rather work in a (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: how do I build my own pcode?
 
You can pick up the pcode source from the MIT web site at (URL) file contains the source code for 2.8 pcode with instructions on how to re-compile under msd*s. I have modified the source to use larger/smaller LCD displays, although they need to be (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  HandyBoard 10-16 Servo support
 
I am trying to develop simple Hardware/Software to support up to 16 servos from the HandyBoard. A theoretical constraint of my plans is that only about 10 of the 16 connected servos will be able to actively hold position at one time. I plan to do (...) (29 years ago, 5-May-98, to lugnet.robotics.handyboard)
 
  Re: HandyBoard 10-16 Servo support
 
"HC" is for CMOS chips "LS" is for Low-Power Schottky chips Brian Carvalho Devry Institute New Jersey (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  256 Motor Power Resolution
 
Hi All, Has anyone noticed that if you slightly modify Julian Skidmore's LIB_HB.C code that one can get 256 motor power levels rather than 100? I took the following code in LIB_HB.C: void motor(int m, int speed) { if (speed>100) speed=100; if (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Re: L293d
 
Hi Paul, You can visit Handy Board WEB and look under "Get One" . Pick component button under "Get One" you will see a couple of places that have L293D. -Pandit ---...--- (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  porting IC 3.2 between computers
 
I need to bring my IC 3.2 program to another computer. Do I need to reinstall the files from the original execuatble? Or can I just zip up my IC directory and unzip it on another computer? ---...--- ericson mar Master of Engineering Candidate (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Re: DS1233 Monitor Chip
 
I already tried it. Works fine. Thanks, (...) -- ---...--- ipscone@halcyon.com Shoot-To-Win! Protect the 2nd Amendment! Your rights may be next! ---...--- (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Re: HandyBoard in Germany
 
Hi Rich, so wie es sich ließt, kannst Du besser deutsch wie ich englisch. Vielleicht sollten wir eine Deutsche HB-User Ecke einrichten :-) :-) - Mal sehen was Fred dazu sagt.- Da mein englisch nicht das beste ist, habe ich so manches mal Probleme, (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Re: DS1233 Monitor Chip
 
I used the MC34064 in both of the handyboards that I built. WARNING !! The pin out the DS1233 and MC34064 is DIFFERENT! You need to rotate the MC34064 by 120 degrees. Check the pin out before inserting the MC34064. If you do not rotate it, the (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  LCD Commands
 
Is there some documentation somewhere that shows the commands required to talk to the display. I would like to control the display from assembly code and I need to know what these commands are. I already know how to talk to the display using the A, (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Re: HandyBoard in Germany
 
Hallo Carsten, es werden immer mehr Deutsche oder zumindest deutsch sprechende Mitglieder in der HB-User Gemeinde. Wir sollten tatsächlich überlegen, wie wir eine solche "Ecke" einrichten könnten. Ein Bezugsquellennachweis wäre sicherlich eine gute (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Re: **handyboard**
 
(...) No it's actually quite easy, the only thing is you have to do a lot of soldering. Be careful of the HC373 which is mounted directly onto the board as if it is damaged by heat, then you will have a "nice" time desoldering it... To drive both (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Multitasking
 
Hello, I am multiplexing 5 LED displays through the Handy Board, but I am getting excessive flicker as in the brightness of the displays is not constant...the intensity of the displays varies from time to time. Does anyone, then, have a program to (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  * the handy-board manual*
 
Hello where can I find the handyboard manual to download? thanks -mike (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Re: LCD Commands
 
(URL) is one of the many FAQ's on the net for LCD's. (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Re: Handy Board problem
 
I use the Siemens SFH506-36 instead of the Sharp, and it works just fine. I know there also is another compenent you can use, but I don't know the name of it anymore, sorry. Perhaps if Maarten Emke reads this, he knows what I mean. Be carefull by (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)
 
  Re: * the handy-board manual*
 
The HB HP ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical Engineering The Cooper Union for the Advancement of Science and Art ---...--- (...) (29 years ago, 6-May-98, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR