| |
Rob Farver wrote:
>
> On Mon, 13 Mar 2000 05:42:48 GMT, "Frank Filz" <ffilz@mindspring.com> wrote:
>
> > In lugnet.trains, Bram Lambrecht writes:
> > > "Frank Filz" <ffilz@mindspring.com> writes:
> > > > Unfortunately, my scheme works in terms of 2x4 tiled areas, which
> > > > means I need to build a 4x4 tiled area with the "Sebulba" 2x2 tile
> > > > in the center
> > >
> > > With some creative engineering, you should probably be able to fit create
> > > just a 2x2 area, but you might have to sacrifice some interior space...
> >
> > Yea, with a wide enough area, one could use the 2x2/2x2 brackets. It would
> > need a depth of 4 for each side though (meaning a container at least 8 wide).
> >
> > There might also be ways to use the 1x1 brick with studs on all 4 sides.
> >
> > Unfortuantely, to use the 2x2 Selbulba tile, and match up the orange and black
> > parts with adjacent bricks, it needs to be 1/2 plate above the brick boundary
> > since the 2 stud width corresponds to a 5 plate height, so each half is 2.5
> > plates high.
> >
> > What elements besides a 1x1 brick w/recessed side stud and the 1x4/1x2 bracket
> > have a half plate dimension?
> >
> > Frank
>
> Thin walls. Here's my solution, only problem being it requires a 1x2 orange
> thin wall. I don't think they exist (yet). I just built this on a 4x4 plate
> to try it out, hopefully you can follow along.
>
> On your black 4x4 plate at the center edge, put 2 1x1s w/ single side studs
> next to each other. This is your attachment for the Sebulba tile. Behind
> these two bricks put two 1x2 plates with single stud so that the single studs
> are parallel to the bricks. On top of these plates put a 1x2 plate, 1x2 brick,
> and 1x4/1x2 bracket, facing the Sebulba tile. On the 1x4 part attach the
> non-existant 1x2 thin wall. This just reaches over the tile enough to hide
> the opening, a 1x4 or larger brick or plate over the top (after building up
> the wall) finishes the job. This only uses 3 studs back so you can still
> build to 6-wide, at the expense of blocking the interior.
I think I see one thing which doesn't meet my criteria, the tile will
not be flush with the surface of the wall, it will stick out 1/2 plate
thickness. My solution leaves it flush with the surface of the wall.
I don't mind not having an interior to the container, which is good,
there is no good solution which is only 1 stud thick.
The 1x2 thinwall solution might be useable in other ways though, I'll
have to play with it. I had one partial solution which had 1/2 plate
thickness gaps above and below the tile (and the tile was flush with the
brick wall).
--
Frank Filz
-----------------------------
Work: mailto:ffilz@us.ibm.com (business only please)
Home: mailto:ffilz@mindspring.com
|
|
Message has 2 Replies:
 | | Re: Containers
|
| IRL name and logo plates are often welded onto the rib bulges so "appear" to stick out. However they don't actually do so due to clearance reasons. If you're not going to be stacking your sebulba container next to other containers and not going to (...) (25 years ago, 13-Mar-00, to lugnet.trains, lugnet.build)
| | | Re: Containers
|
| (...) Wrong! :) :) Check this out. I just whipped this up as a solution to your problem. As far as I can tell, it matches all criteria mechanically. The only thing I'm not sure of is whether or not the 1x2x2 panels come in orange... (...) (the ">" (...) (25 years ago, 13-Mar-00, to lugnet.trains, lugnet.build)
|
Message is in Reply To:
| | Re: Containers
|
| (...) Thin walls. Here's my solution, only problem being it requires a 1x2 orange thin wall. I don't think they exist (yet). I just built this on a 4x4 plate to try it out, hopefully you can follow along. On your black 4x4 plate at the center edge, (...) (25 years ago, 13-Mar-00, to lugnet.trains, lugnet.build)
|
41 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
