| |
In lugnet.trains, Frank Filz writes:
> Rob Farver wrote:
> >
> > On Mon, 13 Mar 2000 05:42:48 GMT, "Frank Filz" <ffilz@mindspring.com> wrote:
> >
> > > In lugnet.trains, Bram Lambrecht writes:
> > > > "Frank Filz" <ffilz@mindspring.com> writes:
> > > > > Unfortunately, my scheme works in terms of 2x4 tiled areas, which
> > > > > means I need to build a 4x4 tiled area with the "Sebulba" 2x2 tile
> > > > > in the center
> I think I see one thing which doesn't meet my criteria, the tile will
> not be flush with the surface of the wall, it will stick out 1/2 plate
> thickness. My solution leaves it flush with the surface of the wall.
>
> I don't mind not having an interior to the container, which is good,
> there is no good solution which is only 1 stud thick.
Wrong! :) :)
Check this out. I just whipped this up as a solution to your problem. As far
as I can tell, it matches all criteria mechanically. The only thing I'm not
sure of is whether or not the 1x2x2 panels come in orange...
> 0 Name: walllogo.DAT
> 0 Author: Karim Nassar
> 1 16 0 24 0 1 0 0 0 1 0 0 0 1 4865.DAT
> 0 STEP
> 1 16 10 30 -2 1 0 0 0 0 -1 0 1 0 2420.DAT
> 1 16 -10 30 -2 0 0 -1 -1 0 0 0 1 0 2420.DAT
> 0 STEP
> 1 16 -40 0 0 -1 0 0 0 1 0 0 0 -1 4864.DAT
> 0 STEP
> 1 16 40 0 0 -1 0 0 0 1 0 0 0 -1 4864.DAT
> 0 STEP
> 1 16 0 -8 0 1 0 0 0 1 0 0 0 1 3666.DAT
> 0 STEP
> 1 1 0 20 -10 1 0 0 0 0 -1 0 1 0 3068warn.DAT
> 0
(the ">" are to keep lugnet from bouncing this post due to Ldraw data)
--Karim
--Master Legosmith :)
|
|
Message has 1 Reply:
 | | Re: Containers
|
| (...) Well there's nothing like saying "can't be done" to shake out the solution... (...) Ooh, naughty... :-) Could you generate a JPG or two, or just describe it? (I don't have a way to look at .DATs at work). Hmm, I just tried to look at all the (...) (27 years ago, 13-Mar-00, to lugnet.trains, lugnet.build)
|
Message is in Reply To:
| | Re: Containers
|
| (...) I think I see one thing which doesn't meet my criteria, the tile will not be flush with the surface of the wall, it will stick out 1/2 plate thickness. My solution leaves it flush with the surface of the wall. I don't mind not having an (...) (27 years ago, 13-Mar-00, to lugnet.trains, lugnet.build)
|
41 Messages in This Thread:
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
