 | | Re: IR Demodulator Range Finder Hack
|
|
(...) (2 URLs) the referring page. I have used this "hack", and found it to be quite extensible and flexible. We used "high output" IR LEDs, from Radio Shack (I don't have the part number, but, if you go in there, its the light light blue ones) that (...) (27 years ago, 18-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Applications?
|
|
(...) Yes. (...) Yes, if the motors draw less than 1Amp of current when stalled. (...) Yes. (...) You can drive bipolar stepper motors using the on board h-bridges. (...) Yes. The typical way to do this would be to attach your directional detector (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | hexapodial walkers & other stuff
|
|
hi. I was looking thru the new Robot Store catalog (www.mondo.com) and saw that they were selling hexapod walkers. I was wondering has anyone here built a hexapod? Mondotronix had it so that there were 2 horizontal crossbars per 1 vertical leg. (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | subscribe
|
|
subscribe shahian@csulb.edu (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Applications?
|
|
Hello to all Robo-maniacs!!! I was just wanted to make sure some thoughts about the Handyboard. 1 Can you connect it with a PC and after you make a programm in C, load it in the handyboard (and after disconnection can you apply the program on your (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | array variables
|
|
Hello all, is it possible to create an array variable in the .icb file, if so how do you do it? -tanis (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: 293s, Cable
|
|
In your message you said: (...) this isn't the problem. (...) please do the following, and specify the point of failure. 1. Open a terminal emulator program on your CPU (e.g., ProComm for DOS, HyperTerminal for Windows 95, ZTerm for Mac). Select the (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR Demodulator Range Finder Hack
|
|
(...) I would be interested to hear about this too please. We are running a Group Design Exercise (our own version of a Lego robot competition). Designing the staff entry (to check the idea was feasible in the short time alloctated to the exercise) (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Platinen zu verkaufen
|
|
Soory, this offer is valid for Germany only. So it's written in german. Hallo, ich hab hier noch eine Platine fuers Handy-Board uebrig. Eigentlich sinds 2. Also das eigentliche Board + Schnittstelle. Wer also noch Bedarf an so etwas hat, sollte sich (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | 293s, Cable
|
|
We're trying to build a handyboard, and we attempted to dl the .s19, but it doesn't work. It gives the connecting at 1200 baud.... message but nothing happens after this. Two issues that I believe may be causing this are: 1) we don't have the 293 (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | IR Range finder
|
|
I am posting this for in case any body is interested as I know that I will be trying to make use of it. I apologise in advance to anybody who already knows how to do this, or does not intend to use such a range finder, but I imagine there are a lot (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Ooops.
|
|
It's unlikely you killed the MCU, there are 1k resistors in series with the RxD and TxD lines. Go to the assembly manual, and run through the series of tests that verify proper operation of the Interface/Charger Board. (URL) your message you said: (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | External motor power
|
|
I want to use an external battery for motor power. I see the power expansion header apparantly for this purpose but it appears that I have to cut a trace to disconnect the HB battery from MOTORPWR. Is true? Is there anything else that I may have (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | IR Demodulator Range Finder Hack
|
|
A few months ago I found information on how to modify the Sharp IR Demodulator to produce an analogue voltage relating to the strength of IR received. The problem is that I have lost the information and can't remember where I saw it. Has anybody (...) (27 years ago, 17-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Ooops.
|
|
Help! I accidently plugged a network rj11 cable between my HB and the serial interface board. It seems that I released the smoke genie from R 11. I have replaced the resistor and the MAX 232 but I'm not getting the board to sync. Is there anything (...) (27 years ago, 16-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Shaft Encoders
|
|
While looking through the code 'pcode.asm' I came accross reference to various encoder routines that enable Y0 and get RSE code from the data bus. How can I call these within a C Programme ? I've not seen this feature documented anywhere (or maybe (...) (27 years ago, 15-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Motorola Reference Guides
|
|
I just got the set of Motorola HC11 guide books and reference manuals. I can highly recommend them - I am now able to understand the processor better, and how to take advantage of its many facilities. However when requesting them from the web site I (...) (27 years ago, 15-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR devices
|
|
The IR led I assume would be the transparent one and the detector would be the black one? There are 2 leads on the transmitter and 3 on the detector, how and where should I connect it to the HB? Any diagrams available? If this works, I have about 10 (...) (27 years ago, 14-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | AD: Wirz Electronics
|
|
Hello Everyone, We have a number of new Microcontroller products that we think you may be interested in: ---...--- Microchip PIC Products: "Programming and Customizing the PIC Microcontroller" book by Myke Predko (URL) Up The Pace" book by David (...) (27 years ago, 14-Nov-97, to lugnet.robotics.handyboard)
|
| |
| | Re: bit_set and Poke
|
|
bit_set in english is "for the byte at this adress, make these bits high". The first argument is the address (i.e. 0x0e). The second argument is the mask which indicates which bits to make high. bit_clear in english is "for the byte at this address, (...) (27 years ago, 12-Nov-97, to lugnet.robotics.handyboard)
|
