To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6146 (+20)
  RE: USB->serial adapter for IR-tower
 
(...) I have an Entrega splitter which adds two serials, a parallel, and four USB's, and it does that kind of stuff just fine. Very cool. I've run Ethernet (10BaseT), my printer, IR, and many other things through it. The best part: the fact that it (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Power steering for 8448
 
I don't have the 8448 or the RCX for that matter but I may have a partial solution for you. I've found that steering is a perfect application for the Micro Motor (part # 5119). The motor is very small but provides a surprising amount of torque. It (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  RE: Power steering for 8448
 
You should be able to get away with just a single rotation sensor. When you power up the RCX, you will not know the position of the steering. Now turn it one way until the rotation stops. You are now at the end point, and know the position of the (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Handy Board software
 
(...) They're both 8-bit microcontrollers with a roughly similar set of peripheral functions (timer, ACD, serial port, etc). But the similarity ends there. The programming model for the H8 is compltely different from the 68xx series. (...) I don't (...) (27 years ago, 9-Aug-99, to lugnet.robotics, lugnet.robotics.rcx.legos)
 
  Re: Using the Motor as a Tachometer
 
(...) I'm not a EE, but here's my take on the situation... Turning the motor increases the electrical potential (voltage) between its two contacts. If the motor isn't connected to anything, then its easy to turn - relatively little energy is (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Darn those definitions (was: The new Super Car)
 
(...) easy (...) Like I said, everything is compressible, with the probable exception of the stuff in a black hole. Even the exclusion principle (the law that controls elecron 'orbits' round an atom) is reconed to be overcome by sufficient force (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Lego is like nanomachines
 
Robert Munafo wrote in message ... (...) a (...) mechanical (...) design. (...) Being serious, this wouldn't work. Scaling down would call for different structures. Eric (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Mechanical question
 
This thread already offers a lot of interesting explanation about the thrack slip, but on the wheels part you may want to have a look at: (URL) in menu: going in circles Animations explain how side slip in wheels is (practically) zero as long as (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  RE: Handy Board software
 
(...) They're both really decent 8bit micros. Similar IO capabilities, and I think the HC11 has better timers, but only 8 bit A/D. I've worked a LOT with the HC11 and it's really a good part. (...) Beleive it or not, there is a FORTH for the HC11 (...) (27 years ago, 9-Aug-99, to lugnet.robotics, lugnet.robotics.rcx.legos)
 
  Re: Using the Motor as a Tachometer
 
(...) SNIP (...) SNIP (...) Todd, The danger as I see it is not electrical but physical. If the sensor mode of the input port is "active" the port will provide power to the motor (sensor). Thus you could have 2 motors either working together or (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  RE: Using the Motor as a Tachometer
 
(...) In fact, this is how the RCX motor controller internally sets the motor up for "brake" instead of "off"... Cheers, Ralph Hempel - P.Eng ---...--- Outside of a dog, a book is a man's best friend. Indside of a dog, it's too dark to read... (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Power steering for 8448
 
(...) Good point! Well I'll have to change my model a bit then - the rotation sensor should not go onto the motor axle, but onto the axle driving the rack (stilled geared I guess). Hmm, what can I use this touch sensor for now?? An extra bumper (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Using the Motor as a Tachometer
 
(...) Try to short circuit the motor used as tarcometer / generator, and you'll see. Also try preventing the second motor from spinning, and you'll experience the same thing. About efficiency: this is not what you are experiencing, but the motor (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Power steering for 8448
 
(...) I wouldn't say /just/ for steering. And in fact I only use in input, since the touch sensor can be connected in parallel with a light sensor or such thing. The touch sensor is by the way only used during initialization, when the outer limits (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Using the Motor as a Tachometer
 
In fact, if you hook up two motors using the black cords and turn one of them, the increased voltage will cause the other one to turn without any physical effort applied to it. That's pretty rad. I'm not sure if I understand the brake concept? Could (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Compressible fluids
 
(...) Um, I'm sorry, I honestly didn't want to keep this discussion alive in ANY form but this is silly. The pressure difference from top to bottom results from the weight of the water on top. Period. If I put a 6 ton weight (shades of Monty (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Compressible fluids
 
Thank you, John! Karen (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: Compressible fluids
 
I think all of you meant with this discussion is that water don't get substantially denser (thick) from the surface to the bottom, right? (...) [ mailto:lau@mail.telepac.pt ] [ (URL) ] -- Did you check the web site first?: (URL) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  help me spend some money!
 
I have a grant of about US$1300.00 to spend on robolab for my high school classes. I teach physical science to 9th and 10th graders. I could use any advice on how to get the most for my $. I need to get about 5 RCX's, plenty of sensors, etc. In the (...) (27 years ago, 9-Aug-99, to lugnet.robotics)
 
  Re: help me spend some money!
 
(...) Once you find all the sensors, etc, that you need, I'd suggest finding some good non-mindstorms technic sets to fill out the collection. The Giant Model (#8277) from two years ago is great -- the predesigned models are pretty stupid, but you (...) (27 years ago, 9-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR