To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4496 (+20)
  Re: rpm of the Geared motor
 
(...) About 360 rpm, according to my measurements. The non-geared motor runs at about 4200 rpm. (...) Regards, Johannes. (28 years ago, 9-Apr-99, to lugnet.build, lugnet.robotics)
 
  Re: Even more remote controls
 
(...) Since you can control the IR LED directly you should be able to get this all working in SW. You will need to modulate the IR with a 40Khz carrier. From there you then turn on and off the carrier to create the start, data and stop bits. This is (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  On 9V battery box #5391 for projects
 
I recently got a 5391 9V battery box from S@H to put my RCX IRPD board into. I cut off all but 3 nubs worth of the box from the end with the switch and removed the battery tensioner at that back. The board fits in nicely with just the LEDs sticking (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: On 9V battery box #5391 for projects
 
(...) DOH! (URL) FRIDAY!!! (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: 4WD 4WS model w/limited slip diff.
 
This photo might help (2 URLs) the rubber-band connection between the two power outputs, whenever the model would go over a bump and one wheel was lifted off the ground, the other wheel would not spin at all and all the power went to the other (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: 4WD 4WS model w/limited slip diff. NOTE
 
PS. THe nice looking photos of the lego elements were cropped from originals found on the Technic Elements Registry: (URL) basically describe the key elements necessary to complete the model. (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Mid-South Robotics
 
If you live in the Memphis, TN...Jackson, TN...Little Rock, AR....Jackson, MS area, I am working to setup the Mid-South Amateur Robotics Society. A group that meets to show off Lego (and other) robotics projects and to swap parts and ideas. If you (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  re: legOS for the helpless
 
(...) Sometimes more than once... :-) I just couldn't resist trying my hand at this, even though Dave beat me to it. Looks like they're both fairly similar. Mine will mail the s-record back to you if you like. I've tested it fairly extensively, but (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Power drain of the motors
 
Is there any way to measure the power drain of a running motor? The reason I ask is that I want to detect when the motor has stalled. I use nqc to program the brick. thanks -chris -- Did you check the web site first?: (URL) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: Power drain of the motors
 
(...) The CyberMaster can! ;-) Maybe there's some way you can connect one input to the motor output? Laurentino Martins [mailto:lau@mail.telepac.pt] [(URL) you check the web site first?: (URL) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Non-Lego mechanics reference / New Ideas?
 
Hi all, Has anyone come across any good basic mechanical reference resources? I have found that patent searches are a tad more complex than what I am looking for. I would be interested in hearing about non-Lego reference sites (or books!!)that cover (...) (28 years ago, 11-Apr-99, to lugnet.robotics)
 
  Non-Lego mechanics reference / New Ideas? (fwd)
 
----- Forwarded message from Kipling Morris ----- From: "Kipling Morris" <kiplingm@javanet.com> Subject: Non-Lego mechanics reference / New Ideas? Date: Sun, 11 Apr 1999 10:54:59 GMT Has anyone come across any good basic mechanical reference (...) (28 years ago, 11-Apr-99, to lugnet.robotics)
 
  **lego motors?**
 
Hi I built a robot and it wont travel straight at equal power levels? Why do I need to set the motors at such different levels to get the bot to travel straight? I am using the click and drag software that came with the rcx. any help much (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: **lego motors?**
 
(...) Quite simply, no two motors run at exactly the same speed for a given power level. (Slight differences in the wheels, or flexibility in the axles will also produce the same effect, although probably much less noticeable) There's no simple (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: **lego motors?**
 
Hmmm, Lego gearboxes. I've just spent two weeks playing with different styles off gearbox. I haven't found a good powered solution yet. The problem being that the standard gears just don't mesh nicely enough. Making a gearbox is simple enough and (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: **lego motors?**
 
I've been thinking in building an automatic gearbox with two speeds. If the motor was making too much strength it would lower the gear, and if it's running too fast it would increase the gear. Is there any design like that already built? Maybe with (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: **lego motors?**
 
(...) Lego's Super Car (8880) comes with a 4-speed gearbox that uses loosely set cogs to engage an axle to an idler gear (I don't know how else to describe it), which means that one can change gears easily at high rpm and not worry about (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Steering a robot
 
It seems all of my inventions have a right and a left motor used to guide the direction of a vehicle. I would be interested in having one motor drive and one motor steer. Has anyone been successful at creating this design? Sidenote: This seems to be (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: Steering a robot
 
I've built several steering robots, but the problem that I've had is that it doesn't provide a small enough steering radius to be useful with my projects. The robots that I have been building generally need to be able to turn on their axis. (...) -- (...) (28 years ago, 12-Apr-99, to lugnet.robotics)
 
  Re: Power drain of the motors
 
That's clever! I don't know of a way to do it but if you discover a way, please post it... ...a more expensive way to achieve this might be to couple an angle sensor to the motor (I don't think there are pass through angle sensors so you'd have to (...) (28 years ago, 12-Apr-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR