 | | Re: Why do it? Was: multi-device output controller
|
|
I think that the solution should also be flexible enough to allow the power to be plugged into either an RCX output port or a battery pack. That way if you didn't want to lug around another battery pack, or if you didn't want to use up another (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Why do it? Was: multi-device output controller
|
|
Ralph, Thanks for reigning in the rabbit chase! As the originator of this thread I'd like to respond to the 'why'... I keep running out of ports on my creations. I see 5 or 6 as a practical limit. My criteria for a solution: 1. Entirely compliant (...) (28 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: External Power Port Problem..?
|
|
(...) Ummm, It's not clear from your post, and I'm sure you have tried this, but have you tried a different adaptor? I tried to drive the RCX from a supposedly 9V wallwart, and it didn't work. The I used my lab power supply and started cranking it (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Why do it? Was: multi-device output controller
|
|
(...) I have checked this out, and if you use the standard RCX firmware (or other firmware that uses the RCX ROM, then you get the waveforms you are talking about at 125Hz 1/(1ms x 8). You also get polarity information - oh no, I've said too much. (...) (28 years ago, 26-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | External Power Port Problem..? (fwd)
|
|
----- Forwarded message from Issac Merkle ----- From: "Issac Merkle" <the_gaff@hotmail.com> Subject: External Power Port Problem..? Date: Fri, 26 Mar 1999 06:08:01 PST I have two RCXs, both of which have stopped responding to power applied to the (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | External Power Port Problem..?
|
|
Esteemed Colleagues, I have two RCXs, both of which have stopped responding to power applied to the external power port. With batteries, they function correctly; with a 9.6v Lithium Ion battery pack attached to the external port, nothing. This has (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
How about an RCX to RS232 connection to use off the shelf components? Check out this link. (URL) sells a simple serial servo contol that services up to 8 motors via an rs232 port ($49.95). I have seen a simple version adapted for a Palm Pilot for (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
Thanks for checking this out. This is important to know. I assume, then, that the duty cycles are 1/8 through 8/8 as well as off, which would be 0/8. Can anybody verify this (with a scope or something)? I have long wondered whether the duty cycles (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Stepper motor design
|
|
(...) It realy depends on what form of stepper motor you are using and how the coils are wired up. if you can arange it as two sets of coils you could drive it by hooking one motor output up to one pair of coils and the second motor output up to the (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) I don't know how NQC drives the ports, but both rcxcc and the RIS software have separate controls for on/off and power level. I just tested setting all 8 power settings - motors operates for all 8. -Wes (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
Right. That is why you cannot use all 8 power levels. The polarity reversal that I am talking about is on the controlling (and only) output. I am already assuming, at this point, that drive power is stuck on as with your external battery box. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) Are you sure? I wasn't, so I went looking. The NQC docs seem to imply 7 powers levels plus off. Which, technically, is 8 levels of PWM, but if you use all of them, a motor is running at all times. That is fine if you use another motor output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
In my example the RCX output was just used to tell this mythical board which output to drive. Power for the output came from a battery box, always set to on. The RCX can't set direction on the battery box (at least not trivially). alex (...) -- Did (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Stepper motor design
|
|
----- Forwarded message from Wes Matchett ----- From: Wes Matchett <wes@augustschell.com> Subject: Re: multi-device output controller Date: Fri, 26 Mar 1999 17:34:25 GMT Now that I have brought up that topic, anyone know how to drive a stepper motor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
(...) [snip] (...) Dunno, I haven't looked yet, I just came up with the idea. (...) Because I felt like it? I've seen it written both ways. [snip] (...) Nope. 0 (speed) means off, no matter what direction you are going, therefore: 0= forward, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 12:33:18 -0500 OK now the details. 6. Send to a MAX232 devices and wallah, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Muscle wire and alternatives
|
|
----- Forwarded message from Joel Shafer ----- Date: Fri, 26 Mar 1999 11:12:57 -0600 From: Joel Shafer <joel@connect.net> Subject: Re: multi-device output controller (fwd) Has anyone tried out the Muscle Wire or electronic pistons from this site? (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
There is no need to waste PWM levels on reverse. You can set the RCX motor output to reverse speeds as well, giving you 7 outputs (fwd and rvs) instead of 3 1/2. You need a bridge rectifier anyway; you might as well exploit it to indicate direction. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller
|
|
(...) There are 8 levels of PWM, so fwd/rev for 4 devices is possible. I originally wanted a separate power input to allow a full 8 levels for each device. This would allow the controller to operate ANY device designed for the RCX ports and not (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | Re: multi-device output controller (fwd)
|
|
Cool. You can also add things like the following: 1. Serial LCD display 2. GPS devices 3. additional infrared send/recieve 4. ANY PC project that is serial port connected! I like the idea of multiple serial channels; this means that you can talk to (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|