To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *44869 (-100)
  Re: C Programming Solution for NXT - Beta Available
 
(...) From the install manual: System Requirements: • Windows 2000, XP based computer with 10MB of Hard Drive Space • LEGO NXT Hardware with LEGO Mindstorms NXT Programming Software Installed and/or • LEGO RCX Hardware with Robolab 2.5 or later (...) (20 years ago, 13-Jun-06, to lugnet.robotics)
 
  C Programming Solution for NXT - Beta Available
 
This email announces a C language programming solution for the NXT. The solution includes a comprehensive graphical IDE, C compiler, a full featured debugger, and replacement NXT firmware. It runs ina Windows environment and is available for (...) (20 years ago, 13-Jun-06, to lugnet.robotics) ! 
 
  Re: NXT electronic additions
 
(...) The cheapest source for LED's that I've found is afer Christmas clearance sales of Philips LED Christmas lights. I picked up several sets of these cheap at Target. Each light socket contains an LED and one of the colors included in the (...) (20 years ago, 13-Jun-06, to lugnet.robotics)
 
  Re: When is "off" off?
 
"Mitchell Lichtenberg" <mlichtsr@bellsouth.net> wrote in message news:J0sw36.1JAt@lugnet.com... (...) The battery box shorts the connection in the off position. Bob (20 years ago, 13-Jun-06, to lugnet.robotics)
 
  Re: When is "off" off?
 
(...) The RCX has the capability to place a resistance accross its output terminals. Removing that resistance provides the free spinning behavior enabled by one of the programmable features. Inserting the resistance gives tighter control of motor (...) (20 years ago, 13-Jun-06, to lugnet.robotics)
 
  When is "off" off?
 
If I attach a motor to a battery box and twist the motor arbor I get resistance EVEN if the battery box is switched off. This means that the current,generated by the motor, is getting through, correct? Is the current just bridging the contacts or is (...) (20 years ago, 13-Jun-06, to lugnet.robotics)
 
  Re: IR-based proximity measurement
 
(...) You're welcome - it's a fun problem. At least partially because it's one of the few times I've had to worry about the speed of bytecode execution under the standard firmware (see below). (...) Given what you are transmitting and how you are (...) (20 years ago, 11-Jun-06, to lugnet.robotics.rcx.nqc)
 
  Re: IR-based proximity measurement
 
Brian, thanks for your advice. it has told me what is happening physically. i build a one shot measurement program to answer your questions. here is the measurement result: Distance to wall: 26 cm (at night) 7740 7696 7666 7641 7639 7613 7613 7593 (...) (20 years ago, 11-Jun-06, to lugnet.robotics.rcx.nqc)
 
  Re: NXT electronic additions
 
(...) That's a better idea because a yellow LED is just a red and a green LED that are both turned on at the same time. Hence there is no additional information in terms of reflectivity than you would have gained from the red and green LED's used (...) (20 years ago, 11-Jun-06, to lugnet.robotics)
 
  NXT electronic additions
 
Here's a link to my NXT electronics folder: (URL) , which contains two experiments: My first experiment was to get the NXT to light an LED, in a similar way to the way the light sensor works. My thanks to Philo for sharing a tutorial of how to (...) (20 years ago, 11-Jun-06, to lugnet.robotics, lugnet.technic, lugnet.announce.moc, lugnet.loc.uk)
 
  Motor Technique
 
Here are some pics of a technique I've used for many years, driving a technic axle from a 12V train motor: (URL) the advent of the RC Car motor, this was the most power that could be obtained from a single LEGO motor and used on a Technic axle, 12V (...) (20 years ago, 11-Jun-06, to lugnet.technic, lugnet.robotics, lugnet.announce.moc, lugnet.loc.uk)
 
  Re: IR-based proximity measurement
 
(...) Well, there were a couple of typos, but only one I found that was critical. If you are using a "max-picking LIDAR" method, you do *not* want to divide by the number of samples. The variable "eyeon" in your code should end up with the brightest (...) (20 years ago, 9-Jun-06, to lugnet.robotics.rcx.nqc)
 
  Re: IR-based proximity measurement
 
(...) i have downloaded the SerialPing.nqc program hoping to get an easy to use proximity sensor. i have modified it to work with only one light sensor. but it shows always -90 on the display. ok, sometimes -89 too. can anybody tell me, what i did (...) (20 years ago, 9-Jun-06, to lugnet.robotics.rcx.nqc)
 
  Rotation Sensor Accuracy [was Re: Newbie needs Help (diff sensor)]
 
Steve wrote on Tuesday, June 06, 2006 5:59 PM <<snip>> (...) <<snip>> I think what is really meant is that most RCX firmware implementations are poor at filtering hardware transient errors. And the Rotation sensor is very "good" at generating (...) (20 years ago, 8-Jun-06, to lugnet.robotics)
 
  Re: NBC News for NXT
 
(...) The source code is not yet available because it is not ready to released. At the moment it is extremely ugly Delphi code. I am in the process of refactoring things, re-writing the parsing code, adding a built-in preprocessor, and generally (...) (20 years ago, 8-Jun-06, to lugnet.robotics)
 
  Re: NBC News for NXT
 
(...) Higher-level languages are in the works. Exactly how close we are is hard to say. John Hansen (20 years ago, 8-Jun-06, to lugnet.robotics)
 
  Re: NBC News for NXT
 
(...) I looked over the doc and it looks pretty interesting. Perhaps I'm not looking in the right place, but I couldn't find the source code. Is it available yet, or tangled up in a Lego NDA? -dave (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) I'm with you until we get here. Attaching at the front of a long nose feels like a bad idea. Any side force on the tow rope will tend to pull the robot off course, and once slightly off course the force only gets worse. In any case, a (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: NBC News for NXT
 
(...) So... How close are we to having a higher-level language based on this (something with syntax close to C)? Is that in the works? (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: NBC News for NXT
 
I really thought the NXT was going to be on network TV. hmm. Steve (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  NBC News for NXT
 
Over the weekend I got my new Mac Mini G4 up and running, installed lots of development tools, copied over my NBC sourcecode and managed to build a working version of the NBC compiler for the NXT brick. I will have a zip containing the Mac version (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) I'll get to that, eventually... there's just too much fun stuff going on, and... (...) A historical point on this. The first time I met Steve was at a sumo event, where I had carefully calculated the correct gear ratio, given the torque of a (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) Not so obvious. If you increase the surface the pressure per surface unit decreases proportionnaly (at least on hard surface)... Actually I would expect little or no variation in traction power. Philo (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) Hmmm - that's unfortunate...but if the 'right' strategy is to go with a non-slipping robot, the measurement of sliption is really a lot less important. (...) Yeah - so many of those basic mechanics equations are only approximations - yet they (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) hmm. This sounds like a good project... (...) All things being equal, I'd put my money on the robot with ten spinning wheels, over a couple (or even ten) stationary ones. I'd also mechanically connect all the motors together, so they drive a (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) As you note in your mini-cooper example, *if* you can keep the wheels from "spinning out", but instead are always in rolling contact with the ground, static friction is what's important... and generally, the static coefficient of friction is (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) That makes sense. (...) Yeah - I agree. So we have to sum some force vectors here. If our robot is pulling to the left, we have a horizontal 'drive' force to the left and a force in the tow rope going off to the right - plus a force due to (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Dave, Actually I am very happy and grateful. I am getting a crash course. Couldn't have asked for more. Raj. (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Steve Hassenplug, Sorry, my mistake. Thank you for the Wiki link and all your help. Raj. (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) The problem is that this is measuring the static friction ("stiction"). That's the wrong thing to measure if your strategy is to jam all the motors full on and progress forwards (we hope!) with all wheels spinning. To measure the dynamic (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) I would have expected that compression would be a good thing because it would increase the area of the 'contact patch' - which increases traction - which is a good thing - right? (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) A rather inventive young man that I know did try exactly that - using the ribbed tubing from the Mindstorms set inside the Mindstorms motorcycle tire. It's a good fit, and a good idea, but I'm not sure how effective it was. (...) One simple (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) It does happen - if you use more that 2 motors or if you try to use a RC motor. The driver circuit limits current around 500mA, and at that rate it is not long before going in thermal shutdown mode. (...) No, you won't see smoke... RCX motor (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
Philo, That's interesting, and looks to explain why it is that I've never been able to observe the RCX output going to thermal or current protection cutoff? I've one largish sumo type bulldozer style robot with 4 treads that can easily push 4-5 (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) Actually it does - barely. With the increased current, RCX output voltage drops, so does motor stall current. See these compared charts: (2 URLs) Philo (20 years ago, 7-Jun-06, to lugnet.robotics, FTX)
 
  Re: Newbie needs Help
 
(...) Thought provoking question. It led me to the conclusion that when the bot is generating it's maximum possible drawbar pull (as limited by the motor and drive train), the weight on the undriven front wheels (I'm assuming a rear wheel drive (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Yeah - bad for a tractor with front-wheel steering - and a need to steer - not so bad for a robot with either no steering or rear-wheel skid steering. This robot really doesn't care if it's front end gets light - but for a tractor it's a major (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) (Or vice-versa!) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Sure, I understand the argument. But this old farm boy has both a few hours in the driver's seat of a farm tractor, as well as a couple of engineering degrees, both of which prompted my cautionary statements. Let me start by saying that I (...) (20 years ago, 7-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) I don't think Dean was talking about torque from the rope tipping the robot; I think he was talking about the fact that a raised attachment point for the rope can result in a downward component of the tension, increasing the force down on the (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) Quite true. My bad. -dave (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
(...) I think you need another pair of gears on one of the wheels to reverse its direction. If you are going to use a rotation sensor to measure the slippage then you need to realise that the sensor is notoriously poor at very low speeds. You'll at (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) What I'm saying is that if the robot is moving along at (say) 3 inches per second - then the drive wheels will get most traction if they are turning at a speed equivelent to 3 inches per second. If they are rotating faster than that (because (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help (diff sensor)
 
Some varied thoughts here: (...) I might be wrong, but my understanding of the Lego differential gearing is that if both shafts are turning at the same rate and direction, the outer gear/shell will turn at the same rate as the axles. Only when the (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Raj, There's a bit of confusion here. I believe the above quote actually came from Steve Baker (posting only as Steve). As Steve Baker pointed out, there is a difference between kinetic (sliding) friction and static friction. ((URL) In the (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Ummm.... that's not the way I remember the mechanics. There is a torque created that is force on the drawbar times the drawbar height from ground. That torque will lift your front end. Doubling your own drawbar height halves your pulling (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) One rotation sensor and a differential will allow you to compare the rotation of two wheels. If the driven wheel and the undriven wheel come in the two sides of the differential, and the rotation sensor is connected to the drive ring, then the (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Dean, Thank you for your response. I am going to get on with the tow rope suggestion right away. You might like to know that your 2002 'Building Lego Robots for FLL' guide was the first thing that I read. Raj (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
You only need one rotation sensor and some fancy gearing. Using a differential in a way similar to the "South Facing Cart" or the stearing drive in a dual differential setup, you could directly measure the amount of spin between a driven wheel and (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Steve, One rotation sensor is allowed. There are also two light sensors, so your idea is definitely doable. The situations that are confusing are when the pull of the other robot prevents your robot from making any headway, as well as when (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Steve, Provided that my robot doesn't tip-over and that only the front wheels are driven. I have seen a video of a robot in last year's competition that opened up into a V-shape. The angle between the arms of the V being greater than 90 (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Steve, Philo's page on 'Wheels, Tyres & Traction' seems to imply that increased speed will not make much of a difference or am I reading that wrong? By 'mechanically connect' do you mean by using two differentials? The maximum 'safe' gearing (...) (20 years ago, 6-Jun-06, to lugnet.robotics)
 
  Mitchel Resnick & NXT were here
 
Finally got a chance to have a closeup look at the much talked about Mindstorms NXT when Prof Mitchel Resnick (of MIT Media Lab) was here for the LEGO MINDSTORMS Education (LME) NXT Regional Pre-Launch at the Singapore Science Centre. (URL) (...) (20 years ago, 6-Jun-06, to lugnet.robotics, lugnet.loc.sg)
 
  Re: Newbie needs Help
 
(...) Real tanks and dozers have lots of little sprung wheels resting along the bottom edge of the track - adding those would give you back that down-force you miss from the center of the track being unsupported. Tank tracks are a subtle thing in (...) (20 years ago, 5-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
Steve Hassenplug wrote: > You can (A) add more weight (B) make it go faster, or (C) add more traction. > Considering you're already at the weight limit (out of parts), option (A) is out. > > Making it go faster is a reasonable option. Geared down (...) (20 years ago, 5-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Well, I'm not exactly an expert - but it seems to me (if the rules allow it) that attaching the tow rope above the center of gravity of the robot and putting the drive wheels at the end nearest your opponent would result in the force of your (...) (20 years ago, 5-Jun-06, to lugnet.robotics)
 
  RCX and Basic stamp
 
can anyone help me. im trying to communicate a basic stamp 2 microcontroller with the RCX 2 via infrared. i dont get the protocol it works on can someone help. -- View this message in context: (URL) from the LEGO Robotics forum at Nabble.com. (20 years ago, 5-Jun-06, to lugnet.robotics)
 
  RE: Newbie needs Help
 
(...) Yes, you would think so. But, they don't. Tank Treads look like they have a big "contact-patch" with the ground. In reality, each one only applies pressure in two points (at each wheel), and even those are not in contact with the ground all (...) (20 years ago, 5-Jun-06, to lugnet.robotics)
 
  RE: Newbie needs Help
 
"BTW, don't use tank treads." How come? Gut feeling is that it would provide more traction? -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...ugnet.com] On Behalf Of Steve Hassenplug Sent: Monday, June 05, 2006 2:36 PM (...) (20 years ago, 5-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) I suspect you're far from breaking gears or axles. However, keep in mind it is always possible (so don't blame me if it happens) :) Keep the distance between gears & wheels small, so the axles don't twist. Sounds like you still have more (...) (20 years ago, 5-Jun-06, to lugnet.robotics)
 
  Re: Newbie needs Help
 
(...) Steve, Thanks for the tips and good wishes. Currently this is what we have: - 3 wheels driven by 3 motors. Each geared down at 15:1 - the wheels do keep spinning when the robot is held in place - very generous size limit, a 250mm cube - so no (...) (20 years ago, 5-Jun-06, to lugnet.robotics)
 
  Some info if you want to use Lejos with Cygwin
 
Hello, Some info if you want to use Lejos with Cygwin: Download Lejos for Linux/OSX/Solaris. (I used v2.1.0) (URL) the sake of comprehension, decompress it in ~/temp/lejos $ tar -xvzf lejos_2_1_0.tar.gz $ mv lejos_2_1_0 lejos $ (...) (20 years ago, 5-Jun-06, to lugnet.robotics.rcx)
 
  Re: Newbie needs Help
 
(...) Raj One major key to making a good Tug-of-War robot will be making it go the "right" speed. If it goes too fast, some of the "power" will be wasted on speed. If it goes too slow, it won't use all the power it has. To change the speed of the (...) (20 years ago, 5-Jun-06, to lugnet.robotics)
 
  Newbie needs Help
 
Hi, I am a newbie and would appreciate some help. My 11 year old has just joined his school robotics club. He will be using set 9794 (Mindstorms for School with ROBOLAB 2.5.4) and has to prepare a robot for a Tug-of-War competition (based on FLL (...) (20 years ago, 5-Jun-06, to lugnet.robotics, lugnet.robotics.edu, lugnet.robotics.rcx.robolab)
 
  Re: BricxCC & Cybermaster
 
Thanks for the quick reply. I've been scouring the internet for pages about Cybermaster, but most of them only exist as dead links in listings. Does anyone know of any 'must-see' CM pages out there? linmix (...) (20 years ago, 4-Jun-06, to lugnet.robotics)
 
  Re: BricxCC & Cybermaster
 
(...) Get the test release of BricxCC which fixes a problem that I introduced in build 3.3.7.10 which breaks serial tower (both IR and RF) communications. (URL) Hansen (20 years ago, 4-Jun-06, to lugnet.robotics)
 
  Re: Getting Serial IR Tower To Work With RoboLab
 
(...) Thank you Claude. I will get a USB RS232 and go forward. I did find that now I cannot select the com4 port in "select Com" within RoboLab. I will try to get to the bottom of this and slowly work on what works. Tom (20 years ago, 4-Jun-06, to lugnet.robotics.rcx.robolab)
 
  Re: Getting Serial IR Tower To Work With RoboLab
 
(...) try GPS8.vi hat you can download at www.convict.lu/Jeune...amera8.llb I added a small sub.vi to GPS8.vi that allows you to find your USB converted serial port. Probably you have it on Com4. You can run this search...vi alone and determine the (...) (20 years ago, 3-Jun-06, to lugnet.robotics.rcx.robolab)
 
  BricxCC & Cybermaster
 
I hope nobody objects to my bringing this up, but not only is this evidently lego robotics related, it's also (very slightly) rcx related. I'd like to try establishing some form of communication between my Cybermaster and RCX units and my first step (...) (20 years ago, 3-Jun-06, to lugnet.robotics)
 
  BricxCC & Cybermaster
 
I hope nobody objects to my bringing this up, but not only is this evidently lego robotics related, it's also (very slightly) rcx related. I'd like to try establishing some form of communication between my Cybermaster and RCX units and my first step (...) (20 years ago, 3-Jun-06, to lugnet.robotics)
 
  Getting Serial IR Tower To Work With RoboLab
 
I am trying to interface a serial IR tower RoboLab 2.5.4 B. The serial tower is connected to com4 via a PCMCIA RS232 1 port card. I can select the com4 port in "select Com" within RoboLab. "Interrogate RCX" does not work. No green light on the (...) (20 years ago, 3-Jun-06, to lugnet.robotics.rcx.robolab)
 
  Re: Problem with RCX
 
(...) I wanted to let everyone know that I was able to fix my RCX and tell you what was wrong with it. There was a bridge between the positive terminal pad and a very thin portion of the ground plane along the outer edge of the PCB. Apparently the (...) (20 years ago, 2-Jun-06, to lugnet.robotics)
 
  a gbc module
 
Photos of a foosball table GBC module. A deep link showing the table, with 6 balls in play: (URL) balls come in from the top of the picture (side of the table) and exit at the goals. By speeding up or slowing down the rotation rate, I can let balls (...) (20 years ago, 2-Jun-06, to lugnet.robotics)  
 
  Camera vs. ROBOLAB, Round 1
 
So here I was, minding my own business and enjoying the last day of my first week of summer vacation, when suddenly an idea popped into my head. This idea was to use my Vision Command camera in conjunction with ROBOLAB 2.5.4, because I had seen (...) (20 years ago, 1-Jun-06, to lugnet.robotics)
 
  Administrivia - duplicate postings
 
Hi. Sorry to have forwarded those half-dozen duplicate postings. Somebody is re-injecting email, and I mistakenly allowed them onto the list. (20 years ago, 1-Jun-06, to lugnet.robotics)
 
  navigator class
 
Hi! I'm controlling my robot with the navigator class. For my recent visual servoing project I need to stop the current travel command and call it once again with new distance information. The old movement should be stopped and the new one started. (...) (20 years ago, 1-Jun-06, to lugnet.robotics.rcx.java)
 
  FIRST LEGO League video
 
Greetings All, Here is a video of a FLL team that I coached: (URL) team was quite good and made it to the the World Festival in Atlanta last month. In the five months leading up to the festivle, they were able to improve their robot to the point (...) (20 years ago, 31-May-06, to lugnet.robotics.edu)
 
  Re: Game Boy + LEGO = Robot
 
(...) Thanks Bernard and Philo, The interesting thing is how they are priced. I would strongly suspect that the ones on the kornylak site are cheaper, and can be builk purchased, which would be a worthwhile advantage over the Charmed Labs ones, when (...) (20 years ago, 30-May-06, to lugnet.robotics)
 
  Re: Game Boy + LEGO = Robot
 
(...) Yes, but if you slightly trim one end of a Technic bush it can be press-fitted in wheel hole and allow easy and tight axle mounting... Philo (20 years ago, 29-May-06, to lugnet.robotics, FTX)
 
  Re: Would You Like To Play A Game Of Chess? I Play Very Well....
 
Oops, sorry about the crosspost to these groups-- wasn't intentional. JOHN (20 years ago, 29-May-06, to lugnet.robotics, lugnet.trains, lugnet.town, FTX)
 
  Would You Like To Play A Game Of Chess? I Play Very Well....
 
(URL) Built by my son, Ross. Portable. I lost my queen in our first game because I couldn't tell the pieces apart. He didn't care;-) Enjoy, JOHN (20 years ago, 29-May-06, to lugnet.announce.moc, lugnet.general, lugnet.robotics, lugnet.trains, lugnet.town, FTX)
 
  Re: Problem with RCX
 
(...) not find any more battery gunk. Everything looked okay, no obvious signs of damage. Since this is a newer unit, the battery tabs are soldered to the board. If I place a meter on the + and - terminals, it shows a short. If I place a meter on (...) (20 years ago, 28-May-06, to lugnet.robotics)
 
  Re: Problem with RCX
 
"steve" <lego-robotics@crynwr.com> wrote in message news:44792D84.80803@...ail.net... (...) (URL) (20 years ago, 28-May-06, to lugnet.robotics)
 
  Re: Game Boy + LEGO = Robot
 
(...) Hi Philo, Yes they are, give or take, the same. However, the Charmed Labs ones have Lego axle holes! Danny (URL) (20 years ago, 28-May-06, to lugnet.robotics, FTX)
 
  Re: Game Boy + LEGO = Robot
 
(...) Have also a look to these: (URL) (same wheels?) shawn to me by Bernard Catt. Philo (20 years ago, 28-May-06, to lugnet.robotics)
 
  Re: Problem with RCX
 
(...) I agree - and furthermore, whilst a dead short might well cause a battery leak (when the batteries get hot, the contents can expand and rupture the cell) - it's kinda unusual for a battery leak to cause a dead short - the corrosive gunk inside (...) (20 years ago, 28-May-06, to lugnet.robotics)
 
  Re: Problem with RCX
 
(...) The dead short could have caused the batteries to leak. That's probably the only way to get batteries to leak in only a week. (20 years ago, 28-May-06, to lugnet.robotics)
 
  Re: Game Boy + LEGO = Robot
 
(...) Ahh, between the two articles; yours and the one on Charmed Labs, I learned a lot about this technology. THANK YOU e p.s. yes those Omni Wheels are very cool! (20 years ago, 27-May-06, to lugnet.robotics, FTX)
 
  Re: Game Boy + LEGO = Robot
 
(...) Eric, I came across this some time ago, and even thought about seriously as a controller, although quids in its a bit pricy to buy the device and a GBA if you havent already got one just to use this. I have just dusted off a page I have on it (...) (20 years ago, 27-May-06, to lugnet.robotics, FTX)
 
  Game Boy + LEGO = Robot
 
A friend pointed this out to me. (URL) e (20 years ago, 27-May-06, to lugnet.robotics, FTX)
 
  Problem with RCX
 
I have a 2.0 RCX that is only about 6 months old. I had just put a new set of batteries in it the other day and it was working fine. I had not used it for about a week and then tried it out and it was completely dead. I opened up the battery box and (...) (20 years ago, 26-May-06, to lugnet.robotics)
 
  Re: NXT Line Follower
 
(...) Good question. I never tried it that way... and now the bot is in pieces for my next idea... (20 years ago, 26-May-06, to lugnet.robotics)
 
  RE: NXT Line Follower
 
Just wondering whether the same (unmodified) program will also work when you set the robot to follow in the opposite direction. It appears that you're following the outer edge of the line and I was wondering about the performance when following the (...) (20 years ago, 26-May-06, to lugnet.robotics)
 
  NXT Line Follower
 
All, I have posted pics and video of my NXT Line Follower. (URL) (20 years ago, 26-May-06, to lugnet.robotics)
 
  Re: robolab 2.9
 
(...) Thanks for the information, guys. Joseph (20 years ago, 25-May-06, to lugnet.robotics.rcx.robolab)
 
  Re: robolab 2.9
 
(...) Just a quick correction. You do need to own a previous version of ROBOLAB. Version 2.9 is just an upgrade. -j. (20 years ago, 24-May-06, to lugnet.robotics.rcx.robolab)
 
  Re: Ultrasonic sensor interactions
 
Hello John, (...) I have played with this command, it seems that only the low nibble of paramater is useful. The interval range goes from 12.5ms for 0 to 3s for 0xf. Interval seems to be roughly proportional to the square of the parameter. I have (...) (20 years ago, 24-May-06, to lugnet.robotics)
 
  Re: robolab 2.9
 
(...) No, you do not need an earlier version. (...) No, it will not work with the 9753 Technic Control Center. But it works with the 9751 Control Lab Interface if that's what you are meaning. CSSoh (20 years ago, 24-May-06, to lugnet.robotics.rcx.robolab)
 
  Re: Ultrasonic sensor interactions
 
(...) Excellent! Thanks for the update, and it's great to know this is availible within the HW. I wish NXT-G had access, but... well, either it eventually will, or LEGO has specificly included goodies in the FW just for 3rd party environments. (...) (20 years ago, 22-May-06, to lugnet.robotics)
 
  Re: Ultrasonic sensor interactions
 
(...) I can confirm that the 0x2, 0x41, 0x0 "off" command does, indeed, turn off the clicking sound that you can hear coming from the US sensor. I can also confirm that the 0x2, 0x40, 0xNN "set measurement interval" command does set the measurement (...) (20 years ago, 22-May-06, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more | 100 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR