| |
Tore Eriksson wrote...
> You mean something like:
>
> 0 Brick 2 x 4
> 0 Name: 3001.dat
>
> 0 INTERIOR BEGIN
> 1 16 20 4 0 1 0 0 0 -5 0 0 0 1 stud4.dat
> 1 16 0 4 0 1 0 0 0 -5 0 0 0 1 stud4.dat
> 1 16 -20 4 0 1 0 0 0 -5 0 0 0 1 stud4.dat
> 1 16 0 24 0 36 0 0 0 -20 0 0 0 16 box5.dat
> 4 16 40 24 20 36 24 16 -36 24 16 -40 24 20
> 4 16 -40 24 20 -36 24 16 -36 24 -16 -40 24 -20
> 4 16 -40 24 -20 -36 24 -16 36 24 -16 40 24 -20
> 4 16 40 24 -20 36 24 -16 36 24 16 40 24 20
> 0 INTERIOR END
>
> 1 16 0 24 0 40 0 0 0 -24 0 0 0 20 box5.dat
>
> 0 TOP BEGIN
> 1 16 30 0 10 1 0 0 0 1 0 0 0 1 stud.dat
> 1 16 10 0 10 1 0 0 0 1 0 0 0 1 stud.dat
> 1 16 -10 0 10 1 0 0 0 1 0 0 0 1 stud.dat
> 1 16 -30 0 10 1 0 0 0 1 0 0 0 1 stud.dat
> 1 16 30 0 -10 1 0 0 0 1 0 0 0 1 stud.dat
> 1 16 10 0 -10 1 0 0 0 1 0 0 0 1 stud.dat
> 1 16 -10 0 -10 1 0 0 0 1 0 0 0 1 stud.dat
> 1 16 -30 0 -10 1 0 0 0 1 0 0 0 1 stud.dat
> 0 TOP END
Uh, maybe. However, if you have a 2x2 brick on top of the 2x4, how do you
leave out only half the TOP section? Or you wouldn't?
Maybe parts should be broken into subparts for analysis?
I think the main problem is, that whether you can switch to a simple part,
depends on the use of the part.
/Lars
|
|
Message has 2 Replies:
 | | Re: L3PLiTE?
|
| (...) In this case you could leave out the interior of the 2x2, but you must use the entire top of the 4x4. In the case of solid wall like structures, however, it could reduce 90% of the blocks to no interiour, and no studs. -Chuck (25 years ago, 30-Mar-00, to lugnet.cad.ray, lugnet.cad.dev)
| | | Re: L3PLiTE?
|
| (...) I think this is a little too much for the task, you don't need to try to remove the interior too, it won't make a big difference. Think of a 2x2 plate, if you can remove the stud4, you're saving 48 quads, 64 lines and 32 optional lines while (...) (25 years ago, 30-Mar-00, to lugnet.cad.ray, lugnet.cad.dev)
|
Message is in Reply To:
| | Re: L3PLiTE? [DAT]
|
| (...) You mean something like: 0 Brick 2 x 4 0 Name: 3001.dat 0 INTERIOR BEGIN 1 16 20 4 0 1 0 0 0 -5 0 0 0 1 stud4.dat 1 16 0 4 0 1 0 0 0 -5 0 0 0 1 stud4.dat 1 16 -20 4 0 1 0 0 0 -5 0 0 0 1 stud4.dat 1 16 0 24 0 36 0 0 0 -20 0 0 0 16 box5.dat 4 (...) (25 years ago, 27-Mar-00, to lugnet.cad.ray, lugnet.cad.dev)
|
19 Messages in This Thread:
 
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
