 | | Re: Dacta angle sensor
|
|
(...) Yes, it works with the RCX. (...) Hrm. That one I don't know about. Your description isn't working for me exactly -- is the hole parallel to the sensor? (28 years ago, 26-Oct-98, to lugnet.robotics)
|
| |
 | | Mind Control now interprets your text file!
|
|
The newest version of Mind Control offers two useful features: 1) It interprets your text file as a program to download into RCX or CyberMaster. (No error checking, it assumes correct syntax and semantics, see example file) This is very useful if (...) (28 years ago, 26-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Dacta angle sensor
|
|
(...) Yes, the hole is on a parallel axis to the sensor. And it is not a 9V part because it uses the old style push-in connector pins. Matt (28 years ago, 26-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Dacta angle sensor
|
|
(...) Huh. Cool. So the sensor is on the long side of the block? (28 years ago, 26-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Dacta angle sensor
|
|
(...) Correct. It's ideal for measuring how far a wheel has turned. I think it was on an old Lego "Turtle". Matt (28 years ago, 26-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Dacta angle sensor
|
|
(...) I missed something. Where did you get this piece from again? -Kekoa (28 years ago, 27-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Dacta angle sensor
|
|
(...) It came with a bunch of Technic stuff I acquired, including a lot of 4.5V stuff. Came from a school in England, I got everything they had :-) Matt (28 years ago, 27-Oct-98, to lugnet.robotics)
|
| |
 | | Messaging between Cybermaster and Mindstorms
|
|
Mindstorms and Cybermaster can't send each other direct messages because of the different physical transmission techniques (infrared vs radio waves). Therefore I added a control panel to Mind Control, which allows the two units to exchange messages (...) (28 years ago, 28-Oct-98, to lugnet.robotics)
|
| |
 | | CYBERMASTERS - how it works ?
|
|
Heya all ! I wanna buy Cybermasters set. But I want to know HOW it works. Must I program this "programable brick" before and then it makes this PROGRAMED motions or can I control this model interactive for example by joystick or mouse ? Like radio (...) (28 years ago, 28-Oct-98, to lugnet.robotics)
|
| |
 | | Controling LEGO trains via Decta Control Lab
|
|
Hi All, I have been working on controlling LEGO trains thru the Decta Control Lab and I got a tip to pulse the power to the rails to better control the trains speed. There are 8 power settings via the ctrl lab and there are really only 2 or 3 (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Mindstorms A/D, 8 bit or 10 ?
|
|
OK, I just got a Mindstorms this yesterday and I've been surfing the various web pages about it (Lots of good info!) and I came across something odd. The specs for the microprocessor say it has 8 bit A/D's (Analog to digital converters), but the raw (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Controling LEGO trains via Decta Control Lab
|
|
(...) To change the speed of the pulsing, you change the frequency. Frequency is measured in Hz. You want more Hz. To change the speed of the train, you increase either the duty cycle or the voltage. The duty cycle is the percentage of time that the (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Re: CYBERMASTERS - how it works ?
|
|
Rene Virsik wrote in message ... (...) program (...) can (...) radio (...) Both. Pplease read yor answer in here. Eric (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Controling LEGO trains via Decta Control Lab
|
|
10Hz is nowhere near fast enough to control a train motor using PWM (pulse width modulation). You need at least 100Hz, and higher would be better. Any of your suggestions will vary the speed of a motor, but the most common is varying the duty cycle. (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Controling LEGO trains via Decta Control Lab
|
|
I was hoping someone would post a solution to the software platform. I would even kill for just the low level API to the control lab direct and write my own Visual Basic OCX for it. The LOGO development environment is a bit forgien to me and is (...) (28 years ago, 29-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Automated brick sorter
|
|
Thanks Josh - I rearranged the site shortly after posting it. Glad you liked my efforts. Huw Joshua Delahunty wrote in message <3630DFF7.A7319B21@a...sc.edu>... (...) (28 years ago, 30-Oct-98, to lugnet.robotics)
|
| |
 | | Cybermasters price
|
|
Heya all ! Don't you know what's the price of Cybermasters in DM (German mark) ? Thanx ! Rene e-mail: virsik@us.svf.stuba.sk (28 years ago, 31-Oct-98, to lugnet.robotics)
|
| |
 | | Re: Automated brick sorter
|
|
Huw, Very nice job. I saw that you used a clutch gear. On thing I've been experimenting with is replacing a clutch gear with a pair of motors, one working like a generator to drive the other. This only works well if the generator-half is one of the (...) (28 years ago, 2-Nov-98, to lugnet.robotics)
|
| |
 | | Welcome newbees
|
|
There are many web pages offering useful info on lego-robotics, but to my knowledge there are currently two web pages specifically set up as convenient entry points if you're new to lego-robotics. Legorobotics page This page gives an overview of (...) (28 years ago, 2-Nov-98, to lugnet.robotics)
|
| |
 | | Mindstorms in Entertainment Weekly
|
|
Hi, all, This week's Entertainment Weekly (dated 11/6/98, with Alanis Morissette on the cover) has in its Multimedia section a brief writeup on Mindstorms. It's pretty basic stuff, written up in EW's typically glib fashion. Also shown is a photo of (...) (28 years ago, 3-Nov-98, to lugnet.robotics, lugnet.general)
|