 | | Re: Question for you Technic pros
|
|
Hi: (...) The cross axle w/ eyes (Lego's name, not mine!) was in only 1 technic set, the small front end loader 8235 (1995). It differs from the two tie rods in that the tie rods can accept a ball joint but the axle w/ eyes cannot. The cross axle (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
|
| |
 | | Re: flexible tubbing
|
|
(...) Hello... Your logging machine sounds like a great model. I hope you're able to show a bunch of detailed pictures in the future. <ICS> (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Question for you Technic pros
|
|
Linc Smith wrote in message ... (...) that (...) I'm not quite sure to which part you are refering at the above site, unless you are talking about the "rack w/ tie rods" which is still quite different from the cross axle w/ eyes #16. But now that I (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: urgent request help !!!!
|
|
-----Original Message----- From: phillip chia [mailto:philchia@sin...et.com.sg] Sent: Friday, December 18, 1998 7:04 AM To: handybd Cc: Mr Peter Lim Subject: urgent request help !!!! Hi Fred and others, I very desperate to debug the problem that (...) (28 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Question for you Technic pros
|
|
John, if I am thinking of the same piece (cross axle w/ eyes #16, 1995) that can be found at (URL) I am aware of at least two very similar piece that is 6 studs (fairly sure) long. They are meant to accept a ball to form a ball-joint. Check out (URL) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Vertical Mill
|
|
I have posted pictures and a QuickTime movie of my new vertical mill at (URL) Bob Fay rfay@we.mediaone.net (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Or you could begin to take a series of actions. If an action results in another hit on the bumper (or a continuous hit) then you abandon that action. So the robot tries everything until something works. That's just like evolution. :) -----Original (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Question for you Technic pros
|
|
Does the "Cross axle with holes" exist in any lengths other than 16? If so, in what lengths does it exist, and if possible what are the part numbers of the other lengths? -John Van (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
(...) What if something hits the robot? (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | dc motor output control
|
|
hi everyone, i need some help on controling the output voltage of the dc motor ports. the output voltage is 9.6V and i like to know if there is any way to clamp down the voltage to 5V or lesser. i try using a enternal resistor but the output signal (...) (28 years ago, 18-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Limited number of MindStorms??
|
|
Just got my kit this morning from Lego Direct :))) One thing worth noting: Fear Airborne Express. Their driver deliverd all the packages for my apartments this morning... by leaving them on the sidewalk in front of the building. My Lego kit had a (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: flexible tubbing
|
|
Thanks for the response. There are some good ideas here. I think that I will start by looking for some thin wall surgical tubing, and looking into gum rubber and silicon tubing. There is a RC model store on my way home, and I think I may be able to (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: flexible tubbing
|
|
Try vacuum tubes at autoparts stores. I was at a Part America yesterday and they had a large variety of vacuum tubes that varied in flexibility. David (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
lego-robotics@crynwr.com wrote in message I think this "bladder" idea might work better as you could have more air displaced (assuming you hit the obstacle with any kind of speed <G> ). Concern for a bump producing enough displacement to move the (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Limited number of MindStorms??
|
|
(...) What's your number? (URL) (...) Jim West NIC Architect MCI Worldcom (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Limited number of MindStorms??
|
|
We'll they're over 86,000 now my RCX# is above that :) Jeff D. Payne UtahLINK Network Operations (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Conductive Foam
|
|
Has anyone come up with any sensors using the conductive foam used in packing IC Chips. Years ago I saw a couple books on home-brew robotics and they were using this foam as a pressure sensor. Pass a current through the foam and the resistance (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Why not set a variable with 1 or 0, e.g. 1=Forward, 0=Backwards. This way when the robot hits something you would know what direction it's traveling in. I haven't tried this, it's just an idea. -----Original Message----- From: Fred Read (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | Re: All-around-the-robot bump detection
|
|
How 'bout this as an alternative. A flexable containment, possibly the moderate diameter rubber tube, inside which are two circuits. One is a continuous metal strip which runs along the inside edge of the outside wall of the tube. The second is a (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|
| |
 | | RE: All-around-the-robot bump detection
|
|
Jeremy makes a very good point ! :) You should be able to get away with 3 (in theory). I think this "bladder" idea might work better as you could have more air displaced (assuming you hit the obstacle with any kind of speed <G> ). me Andrew Phelps (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
|