|
| | Re: Implementation question
|
| Hi Ronald! Ok - my HB is working now. I got the right 1233-10 (10 means 10% of 5v - reset is going up on 4.5v). This seem to work better. Second thing is the 350ms delay seem to be necessary in normal reset. The second thing was that the power (...) (26 years ago, 31-Oct-98, to lugnet.robotics.handyboard)
| |
| iron (score: 1.012) |
|
| | Re: One tip, and a few questions.
|
| In article <01BE14B1.B5C66E80.e...inum.com>, Eric Hodges <eric.hodges@platinum.com> writes (...) In the fifties I built a heat-seeking swivelling "eye" using that method with valve (tube) technology. The IR detector was an old fashioned glass (...) (26 years ago, 21-Nov-98, to lugnet.robotics)
| |
| iron (score: 1.010) |
|
| | Re: Definition of firmare [was: legOS]
|
| stephen p spackman writes: > Hardware is the thing you can't change without a soldering iron or other > tools. > > Software is what you think it is. This thread has wandered too far afield. Take this discussion off the list please. (26 years ago, 1-Dec-98, to lugnet.robotics)
| |
| iron (score: 1.010) |
|
| | Definition of firmare [was: legOS]
|
| Ok, my turn!!!! Hardware is the thing you can't change without a soldering iron or other tools. Software is what you think it is. Firmware is those things that are *both*: it's written like software, but you need to perform hardware-style actions to (...) (26 years ago, 1-Dec-98, to lugnet.robotics)
| |
| iron (score: 1.009) |
|
| | Re: Help
|
| Hi John, It depends on what kind of circuit your infrared sensors are in. An infrared diode or transistor can not be hooked directly into the HB. They have to be biased properly and the signal amplified to be compatible with either the digital or (...) (26 years ago, 25-Nov-98, to lugnet.robotics.handyboard)
| |
| iron (score: 1.009) |
|
|
| iron (score: 1.008) |
|
|
| iron (score: 1.007) |
|
| | Re: Discussion Post: Auczilla
|
| (...) I don't know that anything is "broken" with AucZILLA, I just think that the size of the auction is just far too huge for two people to run with any hope of speed if they actually want to have real lives. I know it took me a matter of weeks to (...) (26 years ago, 16-Dec-98, to lugnet.market.auction)
| |
| iron (score: 1.007) |
|
| | Re: BTII Jetpacks are back
|
| (...) You know, Nellie the Elephant! To Bombay, a travelling circus came They brought an intelligent elephant, and Nellie was her name One dark night, she slipped her iron chain And off she ran to Indistan and was never seen again... Nellie the (...) (26 years ago, 21-Dec-98, to lugnet.general)
| |
| iron (score: 1.007) |
|
| | Re: RCX 2.0 -- ideas.
|
| (...) I'll agree that many people don't have ready access to a soldering iron, but the concepts are pretty simple and the plans for such "extensions" to the RCX are available on the web. I'm a software-type. Odds are 50/50 that I'll burn myself with (...) (26 years ago, 2-Jan-99, to lugnet.robotics)
| |
| iron (score: 1.006) |
|
| | Re: RCX 2.0 -- ideas.
|
| (...) You forget that there are many of us (if not the majority) that neither have the means to build hardware, nor have the knowledge or know-how to build it. I personally know how good I am at destroying hardware. Is not uncommon to try to fix (...) (26 years ago, 1-Jan-99, to lugnet.robotics)
| |
| iron (score: 1.005) |
|
| | RE: interface problem
|
| This can take a long time. Start by making sure that the cable is correct. You can do this by changing the Rx and Tx lines. If this does not help de Maxim serial driver can be faulty. Last check the solder joints.I once looked at them and could not (...) (26 years ago, 13-Jan-99, to lugnet.robotics.handyboard)
| |
| iron (score: 1.004) |
|
| | Re: Help with cables
|
| milind, To check your phone cord, hold the ends together so that the wires are away from each other. Look through the clear connector. The wire colors should line up in this orientation. There is a little more to the DB-25 issue. "Null modem" vs. (...) (26 years ago, 14-Jan-99, to lugnet.robotics.handyboard)
| |
| iron (score: 1.004) |
|
| | Re: Synchro drive in Lego
|
| (...) Well I'd like to control the state of the motors independently so I'm thinking more of a demux (I just aquired 8 more motor kits that were being cleared from Target bringing my total to 10 geared motors and 2 of the older style 9V motors. But (...) (26 years ago, 19-Jan-99, to lugnet.robotics)
| |
| iron (score: 1.003) |
|
| | Re: Speech Synthesis?
|
| A few years ago, "back in the day..." (that is, high school), I did a project that involved creating various vowel sounds as output for some bumper sensors -- different resistances gave different vowels, that kind of thing. The parts came from a (...) (26 years ago, 26-Jan-99, to lugnet.robotics.handyboard)
| |
| iron (score: 1.003) |
|
| | Re: navigation with compass
|
| Sorry for this late follow-up to this old thread. Real Life has kept me away from Lego for the whole week, and finally I am back. Searching for "compass" in the LUGNET news archive turns up 28 entries, so this topic has been discussed long ago, and (...) (26 years ago, 2-Feb-99, to lugnet.robotics)
| |
| iron (score: 1.002) |
|
|
| iron (score: 1.001) |
|
| | Parts availability
|
| To all: I am constructing the Handy Board from 'scratch', since many places want upwards of $200 for a built (and tested) board. I have located most of the required parts, but have not located the following: the 1 uH iron core inductor the 5W 47ohm (...) (26 years ago, 24-Feb-99, to lugnet.robotics.handyboard)
| |
| iron (score: 1.000) |
|
|
| iron (score: 0.999) |
|
| | Re: ldraw.org
|
| (...) It is a work in progress, but a couple things need to happen first. I still need to iron out kinks in the Lego Maniac's Webring site and make it public before starting work on the new ldraw.org site. Also, I want to take my time on this and (...) (26 years ago, 23-Mar-99, to lugnet.cad.dev)
| |
| iron (score: 0.997) |