 | | Re: Programming in Assembly
|
|
A direct link to the page with the documents is (URL) Jürgen Stuber <stuber@loria.fr> (URL) rot 13 "fr" "se" (21 years ago, 17-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Programming in Assembly
|
|
(...) You should look at Kekoa Proudfoots documentation of RCX internals ((URL) and his librcx library to understand the calling convention for the ROM. Then get yourself the H8300 tools (gcc et al) somewhere, this includes assembler and (...) (21 years ago, 16-Jul-03, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Programming in Assembly
|
|
(...) mentioned previously) that describes the on chip I/O features of the H8 if you plan on doing any work with the sensors. (...) to (...) that (...) To turn on motor C forward you would do this: mov #0x02,r0h mov r0h,@0x80:8 The second (...) (21 years ago, 17-Jul-03, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Programming in Assembly
|
|
Cool, thanks I was able to find the doc here: (URL) post about the motor seems helpful, so if I understand right the way to run motor A forward would be "mov 0x030003,r0h mov 0x80,r0h" and for the motor C the same except 0x06? How does the (...) (21 years ago, 17-Jul-03, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Programming in Assembly
|
|
Here's a more direct link for the H8 docs: (URL) down to the literature section and download the two PDFs. For assembly, I would recommend starting off with an installation of BrickOS and perusing the various source code files for the kernel. You'll (...) (21 years ago, 16-Jul-03, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Programming in Assembly
|
|
(...) find the old documentation files is a bit tricky, it took me some time to figure them out. Anyway, take a look at: (URL) look at the product list. Regards, Michael (21 years ago, 16-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Programming in Assembly
|
|
I was interested in writing some assembly code for the lego mindstorm, I don't plan on writing an incredibly complex program though. I am learning asm for the z80 chip so I have a little experience. I only want a single threaded application with one (...) (21 years ago, 16-Jul-03, to lugnet.robotics.rcx, lugnet.robotics.rcx.legos)
|
| |
| | Re: Modifying the BrickOS source code
|
|
Thanks Joe, it makes sense now and I understand it is something that is difficutl to explain esp, through a message board. Thanks for helping me out... Mike (21 years ago, 15-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Modifying the BrickOS source code
|
|
Here is a visual representation: [ KERNEL ]mm_start[ HEAP ] The heap will contain ALL of the following: User Programs, User Allocated memory, Kernel allocated memory (not including static/global variables and constants). The only thing that is prior (...) (21 years ago, 15-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Modifying the BrickOS source code
|
|
(...) Thanks for the description Joe, but in the above paragraph you seem to contradict yourself, you say that mm_start is the end of kernel mode, but alos that user programs are located above mm_start I do not understand that part, did you mean (...) (21 years ago, 15-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Modifying the BrickOS source code
|
|
Mike, IIRC, mm_start is the beginning of the heap. When the system or a user program requests memory (new in C++ or malloc/calloc in C) the memory is taken from this block (from mm_start to the end of memory) What might be confusing is how the (...) (21 years ago, 15-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Modifying the BrickOS source code
|
|
Thanks to all with the help, I finally got my new News setup info (my original login wasnt working so I had to re-sign up but it took about 2 weeks to hear from lugnet, so Charlie posted some stuff for me). I am looking at mm.c for my project and I (...) (21 years ago, 15-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOS motor-output: Subject to change?
|
|
Do you use another firmware downloader besides firmdl3? Recent changes to BrickOS changed the memory layout a bit and this could be an issue. For example, I just discovered that the nqc firmware downloader doesn't like firmware files with (...) (21 years ago, 15-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOS motor-output: Subject to change?
|
|
Hi, I remember. I have tried brickOS 0.2.6.10 but I had problems with downloading the firmware. I was unable to get the new kernel into the RCX. I do not have this problem with 0.2.6.9. Thanks, Dietmar (...) [...] (...) [...] (21 years ago, 14-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help with lnp
|
|
(...) (URL) the latest 0.2.6.10 version. Regards, Michael (21 years ago, 9-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help with lnp
|
|
I guess I should have been more specific initially. Our question, more precisely, is which version of brickOS can we use on regular redhat linux? We will use your directions as well, but what we were really stuck on was which of the brickOS versions (...) (21 years ago, 9-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help with lnp
|
|
Hello Katie, (...) A good decision. (...) To install software on (RedHat) Linux, you will use a program called rpm. Rpm is a packet manager; it can install new programs, you can ask rpm if a package is installed, you can update an existing package (...) (21 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help with lnp
|
|
(...) So if you don't want to take the time to configure linux, then you can perhaps try to download legnoppix. Legnoppix is a linux distribution bootable on CD you don't need any installation and it include all lego tools available in linux (not (...) (21 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: BrickOS motor-output: Subject to change?
|
|
Hi Dietmar, Have you tried brickOS 0.2.6.10? Code was added to that version to address this issue. Mark "Dietmar Cordes" <cordes@lepomux.org> wrote in message news:3F0A7BA7.207050...mux.org... (...) (21 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
| |
| | Re: Help with lnp
|
|
(...) We finally decided to take the time and use Linux to try and get lnpd working. Although we are not familiar with Linux, our professors are helping us. Our main problem now though is the installation of brickOS. I know this should be an obvious (...) (21 years ago, 8-Jul-03, to lugnet.robotics.rcx.legos)
|
