To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 851 (+20)
  Re: CyberMaster memory limit?
 
In article <4.1.19981128223400....lepac.pt>, Laurentino Martins <lau@mail.telepac.pt> writes (...) It's even more restricting than that, I think. As far as I know, it only works with Windows 95, NT and later. I don't think OCXes work with Windows (...) (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) I think that theoretically some OCXes should work on Win32s, which is a set of 32-bit extensions to Win3.1. I dunno for sure though -- it's not a big issue in my life. (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) But does it fail to run on your CyberMaster unit as well? (...) Are you saying that you're using NQC to read off the tachometer numbers? If so, what additions to rcx.nqh have you used to achieve this? Fredrik (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Re: legOS corruption
 
Ben Laurie wrote in message <36606582.FFA56883@a....co.uk>... (...) Aha, the flame war has begun :-) I agree with you too Ben, only a fool would spurn the analyser, but if you instrument your project properly and really KNOW the system, you can (...) (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  2 Motors 1 output port
 
Can the RCX drive two motors off the same output port without burning the output driver circuitry? I need all 3 motor ports (1 to drive both wheels, 1 to drive a steering mini-motor, and 1 to drive a grabber/gripper.) Also has anyone sucessfully (...) (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Re: Some sensor and misc ideas
 
(...) part # 15-1959 $49.99 (...) here's a picture of them (URL) also found some here (URL) still not sure they will work the way you want to use them I don't think they transmit two ways. although I have had some sucess talking two ways by placing (...) (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) I forgot one IMPORTANT detail: DON'T USE the AGC() (change the name in the sources because I misspelled it) as control in cycles because NQC is not compatible with it, assign it to a variable instead. For example, don't do things like this: (...) (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Re: Pneumatic Air Tanks
 
(...) There's one here: (URL) just set the tank on my scanner and edited it a bit so sorry for the quality. but I think you can get the idea from it. (...) (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) specific code. (...) with even (...) Works on Windows NT, Win 95, and Linux. NQC runs on Macintosh, although the serial port on a Mac cannot talk to a CyberMaster. Porting to just about any POSIX like environment should be trivial. Someone (...) (28 years ago, 29-Nov-98, to lugnet.robotics)
 
  Left and right axles rotating at same speed
 
In regard to propelling a robot with both the left and right axles turning at the same speed (or, moving in a straight line): Perhaps this was already suggested, but if not, here is another solution that uses only one differential and two motors, (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: Worm Drive Question
 
toys r us has 8735 for around $38. tim (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: Pneumatic Air Tanks
 
Shane Weston wrote in message (...) You will have much better luck with a micro motor on that switch. I can't even imagine what would happen when the switch reached the end of its throw and a geared motor is still going. A micro motor stalls, but it (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Cybermaster Sensors
 
In message <4.1.19981128213514....lepac.pt>, Laurentino Martins <lau@mail.telepac.pt> writes (...) In the book "Mobile Robots" by A.M.Flynn it suggests three bump sensors which are activated by circular plastic skirt made out of acrylic plastic. It (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: Cybermaster Sensors
 
(...) Thinking ahead, and also if I recall because the set had the idler gear in it, I bought several of the rubber-skirted hovercraft some years ago. It isn't flexible but it's soft and it looks cool. And implausibly enough it's real LEGO. Haven't (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) Excuse me for being stupid, but what is AGC()? I couldn't find any reference to it in the rcx.nqh file. Fredrik (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) Automatic Gain Control voltage. I misspelled it in the source (sorry!) -> Change ACG() to AGC(). As stated in the RCX.NQH, refer to the LEGO SDK for information about these functions. The only reference to this function in in the page 45 of (...) (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: Cybermaster Sensors
 
(...) What do you mean parallel? I once connected 2 touch sensors to the same port and they worked like a logic OR if is that you are asking. (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) I can't find any reference to ACG or AGC or SDK in the rcx.nqh files from the sources codes or the Windows or the Linux distributions available from (URL) where is this RCX.NQH file of which you're talking? Fredrik (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  Re: CyberMaster memory limit?
 
(...) Try to browse a bit up in this same thread. Somewhere along the way I sent a new RCX.NQH BETA version with enhanced CyberMaster support. Laurentino Martins (28 years ago, 30-Nov-98, to lugnet.robotics)
 
  RE: legOS
 
Firmware is software. It doesn't matter if you burn software into ROM, store it on EPROM, store it as PAL settings, core memory values, etc. Software is software, and firmware is software. (28 years ago, 30-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR