 | | RE: Wot no RCX power connector? —Ralph Hempel
|
| | | (...) My guess is it vanished after they got too many "defective" units back after folks started putting adapters with the wrong voltage on their bricks. Even a wired voltage spike might kill the brick. The battery route is safer from a product (...) (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | |
| | | | | RE: Wot no RCX power connector? —S. Crawshaw
|
| | | | | (...) Correct me if I'm wrong, but doesn't that mean that TLG have effectively been lying if they claimed that the RCX unit itself is still the RCX 1.0? It seems like it may be worthwhile complaining (does anyone know an email address for (...) (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | | | |
| | | | | | | RE: Wot no RCX power connector? —Kevin Bracey
|
| | | | | | | (...) It still says "RCX 1.0" on it. It appears identical in all regards to pictures I've seen online, except the end opposite the IR transceiver is totally smooth and blank, and there are two extra studs on top above where the socket was. That end (...) (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | | | | | |
| | | | | | | RE: Wot no RCX power connector? —Ralph Hempel
|
| | | | | | (...) I'm not sure if its worth complaining about...operationally its still the same product even if you can't plug it into a wall wart. I'm more concerned with any changes to the ROM. Perhaps Kekoa can shed some light on this if someone was to ship (...) (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | | | | |
| | | | | | | | Re: Wot no RCX power connector? —Kekoa Proudfoot
|
| | | | | | (...) I doubt there will be significant changes to the ROM. For starters, if somebody has both an old and a new RCX, try downloading the old firmware into the new RCX. If it works, the ROM interface is the same. If the ROM interface is the same, it (...) (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | | | | |
| | | | | | | | RE: Wot no RCX power connector? —Ralph Hempel
|
| | | | | | (...) I've read that the end where the power connector was is "thinner" which is OK since the connector was mounted on the component side and would have added to the hight required. The "smoothing caps" could be eliminated in a battery only design, (...) (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | | | | |
| | | | | | | | RE: Wot no RCX power connector? —Kevin Bracey
|
| | | | | | (...) I don't think so - it looks the same shape as the pictures of RIS 1.0 RCXs I've seen. I doubt they would change the external shape as it would cause problems with plans in expansion kits etc. I expect there's just a lot of empty space inside. (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | | | | |
| | | | | Re: Wot no RCX power connector? —Markus L. Noga
|
| | | | | (...) Interesting enough, I once withdrew the power connector on a unit under full load - sensors, motors, everything on - because the task manager had gone into an endless loop. After duly waiting a couple of seconds, I reinserted the plug. Blue (...) (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | | | |
| | | | | | | RE: Wot no RCX power connector? —Ralph Hempel
|
| | | | | | (...) HaHaHa - What about the one Dave Baum developed NQC on, and the one you used for LegOS, and the one I used for pbFORTH? I'll bet they would sell as a matched set. I can see it now...... I guess if Kennedy's golf clubs are worth $750,000 these (...) (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | | | | |
| | | | | | | | Re: Wot no RCX power connector? —Markus L. Noga
|
| | | | | | (...) Hah. Mine has a power connector. It's sitting on my desk, light as a feather, with no batteries whatsoever. Now, if I could stop tripping over the DC cord... (25 years ago, 19-Oct-99, to lugnet.robotics)
|
| | | | | | |
| | | | | Re: Wot no RCX power connector? —Dave Baum
|
| | | | (...) Another guess - again pure speculation - is tha having an external adapter option made certification more difficult in one of the non-U.S. markets. I believe 1.5, aside from being an update for U.S., is also going to become the (...) (25 years ago, 20-Oct-99, to lugnet.robotics)
|
| | | | |
| | | | | | RE: Wot no RCX power connector? —Tilman Sporkert
|
| | | | | The Scout (from the Robotics Discovery System) doesn't have a power connector either. It is quite possible that the decision to remove the power connector from Mindstorms products was made during the development of the Scout. There was only a single (...) (25 years ago, 20-Oct-99, to lugnet.robotics)
|
| | | | | |
| | | | | | | RE: Wot no RCX power connector? —S. Crawshaw
|
| | | | | | | (...) In the 1999 catalogue from Commotion (UK), there's a Lego power pack, which is pictured near to the control lab interface and the control centre. They don't specifically say that either of these devices need it (at least, I don't think so), (...) (25 years ago, 20-Oct-99, to lugnet.robotics)
|
| | | | | | | |
| | | | | | | Re: Wot no RCX power connector? —Kevin Loch
|
| | | | | | (...) The power adapter that comes with the train sets works fine with RCX. KL (25 years ago, 20-Oct-99, to lugnet.robotics)
|
| | | | | | |
| | | | | | Re: Wot no RCX power connector? —Soh Chio Siong
|
| | | | (...) Besides the RCX, I've two other sets that can be run off an external ac adapter - #8485 Technic Control Center and DACTA #9751 Control Lab Interface. Both of them come with an external adapter. The Technic Control Center can also be run off (...) (25 years ago, 20-Oct-99, to lugnet.robotics)
|
| | | | |
| | | | | | Re: Wot no RCX power connector? —Jacob Schultz
|
| | | | (...) I guess TLG still tries to aim their product at children => Childres build cars => Cars cannot be plugged in and drive at the same time => Remove connector because it is not needed => lower production cost. Or maybe the arrows should be turned (...) (25 years ago, 20-Oct-99, to lugnet.robotics)
|
| | | | |
