To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 6466 (+20)
  Re: r/c servos
 
(...) The answer is pretty simple, actually. In order to control a servo, you need to use pulses whose lengths are on the order of 1-2 ms. The more steps you get in that range, the more servo positions you can use. NQC can't produce pulses as short (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  a correction! to r/c servo
 
Sorry about that! The resulting 0.03 mS pulse width increments would result in 5 degree increments in the position of the servo shaft. How about that? JB -- Did you check the web site first?: (URL) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) I think what John was trying to say was that pulse widths between 0.7 ms and 2.0 ms give servo rotations between 0 and 180 degrees. With 45 steps in that range, you can control the servo in 5 degree increments. Seems to me he was approximating (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
okay.. how about this.. avg servo needs.. 60hz pulses.. 1.0ms pulse width = end point 1.5ms pulse width = middle of rotation 2.0ms pulse width = other end point that is the form of the data to the servo. so you need to out put pulses 60 times a (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) That doesn't make sense either. If a single step of 2.0 ms causes 180 degrees of rotation, then how does 45 steps allow you to control it 5 degrees at a time? (...) Are you saying that the servo actually operates in steps of one degree each? (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
Ok, Here's my 2 cents on servos...read to the bottom if you are interested in helping to develop the code for this. The servo takes a 60Hz (approx) pulse width signal between 1 and 2 msec The pulses are fed into a little circuit that generates an (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) OhOh, I've piqued my own interest. I've looked at the H8 hardware manual and the RCX internals. The OC1A triggers every msec, except the stupid routine clears the Free Running Timer every time!!!! So much for using the OC1B, maybe. The minimal (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) Okay! Finally I got it! (-: It sounds to me like servos can't rotate continuously in the same direction. In other words, they're good for steering but not for turning the wheels that make the car go. Is that right? Anyway, having heard that (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) There are multiturn servos for winches in RC sailboats, but they are REALLY expensive. (...) Well don't give up too fast. They ARE useful for steering, or lifting, or grabbing because we can set the limits of motion. This makes things like (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Using RCX with Lego Trains
 
I just picked up the Lego "Railway Express" set (#4561) last night. It comes with a "Toy Transformer" electrical plug (adaptor). The label on the plug says (North American version): Input: 120 VAC 60 Hz 0.12 A Output: 12 VAC 7 VA Would this work as (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) Almost exactly how I'd do it. The problem is what if OCIB must be set to a small value, and the FRT has already passed this value when the OCIA handler sets up OCIB in step 3? This problem is solvable. If the total interval is closer to 1 ms, (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  Re: r/c servos
 
(...) Let's say a 0.7 ms pulse results in a rotation of 0 degrees. Let's say a 2.0 ms pulse results in a rotation of 180 degrees. If all you had were 0.7 ms pulses and 2.0 ms pulses, you'd be able to choose either 0 degrees or 180 degrees, resulting (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) Exactly. See (URL) examples. These servos have a little disc or cross on top with holes at the edges. The servos can turn the disc only 45 degrees in each direction. They are used for moving flaps or rudders on model airplanes. You bend a 90 (...) (27 years ago, 20-Aug-99, to lugnet.robotics)
 
  RE: r/c servos and firmware
 
(...) Whew! I'm glad I got that much right :-) (...) We could check OC1B and if it's "close" just turn off the motor...as far as the long timer goes, OC1A should always force the output off...on the other hand, the OC1B could be set NO GREATER than (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) In (...) make (...) least (...) Hello, New mindstorm user...been lurking for a while. WRT to servo motion -- it is fairly easy to modify standard servos for continuous motion. $ would put this motor about the same cost as lego so not sure of (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: r/c servos and firmware
 
(...) Thinking about this more, I do not know what I was thinking earlier. Since you are in an ISR, you know can count the number of cycles in the instructions between reading the FRT and enabling the OCIB interrupt, and you can estimate "close" (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: Using RCX with Lego Trains
 
Hello, I have used my RCX to control my Lego train using the wall wart for the train for power. You can run the train off of the bateries but it is pretty pathetic. (I did it once by accident.:)) I set up a simple oval track that used th e light (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  Re: New web pages
 
(...) LOL! I love your expert assitance on the page for the ball-axle connector! Cheers, - jsproat (27 years ago, 21-Aug-99, to lugnet.build, lugnet.robotics)
 
  Motor Speed/Torque Sensor
 
I've developed a circuit that can be used to measure the speed of a powered motor. It works by measuring the voltage generated by the motor during the off period of the PWM. Since the highest power output setting is on all the time, it doesn't work (...) (27 years ago, 21-Aug-99, to lugnet.robotics)
 
  robotic rovers
 
Hello all, I'm trying to construct a rover to make its way around a household environment and avoid obstacles reliably. I'm experimenting with several chassis designs to find one to my liking. (Okay, so I build one design, try it for five minutes, (...) (27 years ago, 22-Aug-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR