To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 1631 (+20)
  Re: All-around-the-robot bump detection
 
How 'bout this as an alternative. A flexable containment, possibly the moderate diameter rubber tube, inside which are two circuits. One is a continuous metal strip which runs along the inside edge of the outside wall of the tube. The second is a (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Why not set a variable with 1 or 0, e.g. 1=Forward, 0=Backwards. This way when the robot hits something you would know what direction it's traveling in. I haven't tried this, it's just an idea. -----Original Message----- From: Fred Read (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Conductive Foam
 
Has anyone come up with any sensors using the conductive foam used in packing IC Chips. Years ago I saw a couple books on home-brew robotics and they were using this foam as a pressure sensor. Pass a current through the foam and the resistance (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Limited number of MindStorms??
 
We'll they're over 86,000 now my RCX# is above that :) Jeff D. Payne UtahLINK Network Operations (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Limited number of MindStorms??
 
(...) What's your number? (URL) (...) Jim West NIC Architect MCI Worldcom (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
lego-robotics@crynwr.com wrote in message I think this "bladder" idea might work better as you could have more air displaced (assuming you hit the obstacle with any kind of speed <G> ). Concern for a bump producing enough displacement to move the (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: flexible tubbing
 
Try vacuum tubes at autoparts stores. I was at a Part America yesterday and they had a large variety of vacuum tubes that varied in flexibility. David (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: flexible tubbing
 
Thanks for the response. There are some good ideas here. I think that I will start by looking for some thin wall surgical tubing, and looking into gum rubber and silicon tubing. There is a RC model store on my way home, and I think I may be able to (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Limited number of MindStorms??
 
Just got my kit this morning from Lego Direct :))) One thing worth noting: Fear Airborne Express. Their driver deliverd all the packages for my apartments this morning... by leaving them on the sidewalk in front of the building. My Lego kit had a (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
(...) What if something hits the robot? (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Question for you Technic pros
 
Does the "Cross axle with holes" exist in any lengths other than 16? If so, in what lengths does it exist, and if possible what are the part numbers of the other lengths? -John Van (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  RE: All-around-the-robot bump detection
 
Or you could begin to take a series of actions. If an action results in another hit on the bumper (or a continuous hit) then you abandon that action. So the robot tries everything until something works. That's just like evolution. :) -----Original (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Vertical Mill
 
I have posted pictures and a QuickTime movie of my new vertical mill at (URL) Bob Fay rfay@we.mediaone.net (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Question for you Technic pros
 
John, if I am thinking of the same piece (cross axle w/ eyes #16, 1995) that can be found at (URL) I am aware of at least two very similar piece that is 6 studs (fairly sure) long. They are meant to accept a ball to form a ball-joint. Check out (URL) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Question for you Technic pros
 
Linc Smith wrote in message ... (...) that (...) I'm not quite sure to which part you are refering at the above site, unless you are talking about the "rack w/ tie rods" which is still quite different from the cross axle w/ eyes #16. But now that I (...) (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: flexible tubbing
 
(...) Hello... Your logging machine sounds like a great model. I hope you're able to show a bunch of detailed pictures in the future. <ICS> (28 years ago, 18-Dec-98, to lugnet.robotics)
 
  Re: Question for you Technic pros
 
Hi: (...) The cross axle w/ eyes (Lego's name, not mine!) was in only 1 technic set, the small front end loader 8235 (1995). It differs from the two tie rods in that the tie rods can accept a ball joint but the axle w/ eyes cannot. The cross axle (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  ROM stuff: Better than PWM
 
So I was thinking about writing a motor driver that is better than what is in the ROM already. Here's the problem: You have a function called once every 1/1000th of a second. You want to allow n speeds of the motor at minimal cost in lookup tables. (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  Re: ROM stuff: Better than PWM
 
(...) Funny - I was thinking of doing exactly the same thing - and also basing it on Bresenham. I've always wondered about 1-bit D/A, but if you actually read the docco it is wrapped up in so much weird signal theory it is very hard to understand (...) (28 years ago, 19-Dec-98, to lugnet.robotics)
 
  Re: All-around-the-robot bump detection
 
Like I said, just ideas, and I haven't yet woken up. Thoughts ? I like the pneumatic idea, but instead of using a cylinder, how about taking a piece of Lego tubing and bending it, so that when you have pressure in the system, the tube wants to (...) (28 years ago, 19-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR