 | | Re: 2 motors, different speeds
|
|
You can put rotation sensors on each wheel, and then monitor them for changes. If one gets ahead of another, then slow that motor down. This works well, but differences in the wheels cause it to turn slightly. Andy (...) (26 years ago, 28-Nov-00, to lugnet.robotics)
|
| |
 | | First Entry for BrickBots.Com and my humbled second entry
|
|
First off, I want to congratulate Mac on being the first builder to enter the Aluminum Can Stacking challenge, and for besting my score before I was even done! While I was fiddling with my robot trying to get the coveted fourth can on the stack, he (...) (26 years ago, 28-Nov-00, to lugnet.robotics.rcx)
|
| |
 | | Re: LNPD problem..again :)
|
|
(...) Have you set up a packet handler on the RCX before sending this? I would guess that if there isn't one, you'll run into something like TCP's "connection refused", which might be what you're seeing. Otherwise, I assume that other LNP stuff (...) (26 years ago, 28-Nov-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Ball-less mice (was :Re: FW: Another DIY sensor)
|
|
(...) I can confirm this, at least for the US market; I just bought the Logitech optical wheel mouse, and it was $30 at Fry's in Campbell, California. (26 years ago, 28-Nov-00, to lugnet.robotics)
|
| |
 | | Re: Lego Mindstorms Europe Demo Tour
|
|
Hi all, (...) no problem with that. BUT ! We took part at the Lego VisionCommand 2000 Competition in Germany. We build an synchrodrive without lego turntables. The Lego chief engineer (don't remember the name, Steven ?????) toke a look at it an was (...) (26 years ago, 28-Nov-00, to lugnet.robotics)
|
| |
 | | LNPD problem..again :)
|
|
hi everybody, im having some trouble with LNPD and was hoping someone out there might get me on the right track again :) PC side: #define MY_PORT 8 #define DEST_HOST 0 #define DEST_PORT 0 #define DEST_ADDR (DEST_HOST << 4 | DEST_PORT) i am trying to (...) (26 years ago, 28-Nov-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Lego Mindstorms Europe Demo Tour
|
|
(...) I suspect the custom pieces that make their way into sets began life as a modification of an existing part. After all, I doubt they wanted to make a custom mold until they were certain it did what they wanted it to. John A. Tamplin (...) (26 years ago, 28-Nov-00, to lugnet.robotics)
|
| |
 | | Re: Lego Mindstorms Europe Demo Tour
|
|
Andy Lynch wrote: >There were also some other bricks modified to press into the touch sensors >on the blue robot. There may have been more, but I stopped looking at that >point. > >Don't get me wrong, the robots were *still* impressive, but I was (...) (26 years ago, 28-Nov-00, to lugnet.robotics)
|
| |
 | | Re: Lego Mindstorms Europe Demo Tour
|
|
----- Original Message ----- From: "Rainer Balzerowski" <balze2@gmx.net> <snip> (...) an (...) I believe you... :-( My wife and I were surprised to find the Mindstorms Mall Tour in our local mall in Ocean County, New Jersey over the weekend. I was (...) (26 years ago, 28-Nov-00, to lugnet.robotics.rcx)
|
| |
 | | Re: monitoring motor revolutions
|
|
(...) The type of navigation you seem to be talking about is called "dead reconning" by aviators. This method requires accurate distance, speed and direction mesurments. Counting motor revolutions does not even tell distance if the surface has (...) (26 years ago, 28-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | Re: 2 motors, different speeds
|
|
(...) Yes I think you're expecting too much. :) Two "identical" motors will go at a *similar* speed if set to the same power level, but chances of them going at the *same* speed is highly unlikely. Bryan (26 years ago, 28-Nov-00, to lugnet.robotics)
|
| |
 | | Re: Mindstorms book
|
|
(...) Of course there are in internet, but what if you don't have it ? Think about 12+ years old kids !?! Rainer (26 years ago, 28-Nov-00, to lugnet.robotics)
|
| |
 | | Re: Lego Mindstorms Europe Demo Tour
|
|
(...) I saw this bar-tender in Frankfurt at the visioncommand 2000 competition. They are obviously running a serial protocol on their 17 RCX ! (One RCX and the IR-Tower were under the desk in a box.) Why don't they offer tese protocol to the lugnet (...) (26 years ago, 28-Nov-00, to lugnet.robotics.rcx)
|
| |
 | | monitoring motor revolutions
|
|
I am currently working on a program that will monitor where a RCX goes. I am trying to establish a coordinate system so if it finds a light it can tell the location of the light. I was thinking about monitoring motor revolutions, but then I am (...) (26 years ago, 28-Nov-00, to lugnet.robotics.rcx.nqc)
|
| |
 | | 2 motors, different speeds
|
|
I have two motors set to the same power levels, but one is always going slightly faster than the other. I've tried it at different power levels but still the same result. Am I expecting too much for them to go at the exact same speeds? Or am I (...) (26 years ago, 28-Nov-00, to lugnet.robotics)
|
| |
 | | Ball-less mice (was :Re: FW: Another DIY sensor)
|
|
The optical mice that do not require a special tablet to operate all use the same sensor, made by Agilent (formaly HP). It is the HDNS2000. The spec can be found here: (URL) this thing has 2 types of output: - PS/2 (connects directly to a PC) (used (...) (26 years ago, 28-Nov-00, to lugnet.robotics)
|
| |
 | | Re: R2-D2 with RXC
|
|
Hi ! I did it ! It was very difficult 'cos info from the Lego WebSite are poor. By inspecting picture on many angles, I understood some tips. So, If you're in trouble, I shall send you from pics from my digital camera. My robot is not perfect but (...) (26 years ago, 25-Nov-00, to lugnet.robotics)
|
| |
 | | RE: Which Palm?
|
|
Time for me to stop lurking. I've written a few Palm applications, and have an RCX, and indeed I was the person who both deciphered the IR protocol that the Furby uses to talk to other toys, and built a laser-emitting LEGO brick: (URL) would love to (...) (26 years ago, 22-Nov-00, to lugnet.robotics)
|
| |
 | | Mindstorms book
|
|
Hi, I bought Dave Baum's on an impuls and now regret it. I don't know about the o'Reilly book, but this one is especially weak on models. Main reason to buy it would be to learn NQC, but there are more sources for that... Duq (26 years ago, 22-Nov-00, to lugnet.robotics)
|
| |
 | | expansion board ?
|
|
i am using the handyboard/expansion board and am using servos for movement i want to be able to have the motors stop in response to a pushbutton being pressed. the button is hooked to the digital in (port 7) on the handyboard here is my code for the (...) (26 years ago, 27-Nov-00, to lugnet.robotics.handyboard)
|