To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *10646 (+20)
  Re: Increasing current output to motors on HandyBoard
 
Another solution to this which is easier but more expensive is to use the output of the motor driver chip to drive solid state relays. You need the relays that use 5 volts for control and that will switch DC. The relays I use have flyback diodes in (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  rpm of the Geared motor
 
Anyone know the rpm of the Geared motor. Thanks LINC (28 years ago, 9-Apr-99, to lugnet.build, lugnet.robotics)
 
  Re: interactive C
 
I'll follow your suggest, thanks for the time you gave me. It has been very useful! Stefano ---...--- (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re : -> Interactive C
 
You help has been really useful, i'm going to visit thi slink immediately! Stefano Falconetti (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Even more remote controls
 
there are a few sites out there wif the required IR info.. I'll try and dig em up tomorrow morning.. I'm gonna get my self a blank GB cart, and the device to upload the data to the cart hopefully this comming friday.. -----Original Message----- (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  RE: rpm of the Geared motor
 
# From: ldsmith@pfc.forestry.ca # Sent: 09 April 1999 07:44 # To: lego-robotics@crynwr.com # Subject: rpm of the Geared motor # ---...--- # Anyone know the rpm of the Geared motor. # If you mean the one that comes with the RIS, it's 350. When I (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: loading s/w
 
(...) legOS has a software solution built-in - when you are ready to quit, hold down the on/off button and press the 'prog' button. Hope this helps! Cheers, Richard (28 years ago, 9-Apr-99, to lugnet.robotics.rcx.legos)
 
  Re: rpm of the Geared motor
 
(...) About 360 rpm, according to my measurements. The non-geared motor runs at about 4200 rpm. (...) Regards, Johannes. (28 years ago, 9-Apr-99, to lugnet.build, lugnet.robotics)
 
  Re: Even more remote controls
 
(...) Since you can control the IR LED directly you should be able to get this all working in SW. You will need to modulate the IR with a 40Khz carrier. From there you then turn on and off the carrier to create the start, data and stop bits. This is (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: Increasing current output to motors on HandyBoard
 
I wonder if this would last since a relay is mechanical and I would assume that it would wear with all that "switching". Doe anyone have any experience with this? Thanks. ---...--- ericson mar Robotics Consultant mar@cooper.edu (212)353-4356 (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re: GCC 2.8.1 for HC11
 
(...) My favorite 68HC11 text resource is: 68HC11 Microcontroller by Joseph D. Greenfield Amazon Price: $87.50 (Wow! I'm sure I didn't spend nearly this much when I bought mine 3 years ago...) The sections on using the 68HC11 timers for interrupts, (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  On 9V battery box #5391 for projects
 
I recently got a 5391 9V battery box from S@H to put my RCX IRPD board into. I cut off all but 3 nubs worth of the box from the end with the switch and removed the battery tensioner at that back. The board fits in nicely with just the LEDs sticking (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  Re: On 9V battery box #5391 for projects
 
(...) DOH! (URL) FRIDAY!!! (28 years ago, 9-Apr-99, to lugnet.robotics)
 
  power supply questions
 
Hello all, I want to power the handy board using the 250watt 12V 9amp power supply of a PC. Any suggestions as to what I should take into consideration before attempting this. A buffer? A fuse? A straight hook up? Why is the HB not supposed to be (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re: interactive C
 
Dear Stefano, Visit el.www.media.mit.edu...index.html to find about the needed software. Mostly you will be needing ic.exe and some library files. You may need a new pcode. Yours sincerely, Nitin (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re: PCB coating
 
First use TINNIT Bright Tin Plate No. ER18 (cheap and does the job) available at Circuit Specialists and Jameco. A better tin plate already mixed can be found at JDR Micro Devices. Then use M.G. Chemicals Conformal Coating which is a flexible (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re: Multi-Processing
 
Dear Kat, Try using music.c that I had downloaded and I have sent as an attachment.This file cantains functions which play music on the piezobeeper. Yours sincerely, Nitin (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Vesit rover
 
Dear friends, You know that we at Vesit, Bombay were making a rover using the handy board. Learn more about it at (URL) sincerely, Nitin (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re: GCC 2.8.1 for HC11
 
(...) You have to get good at reading schematics in this case, period. Schematics are very hard to read at first, but it does get easier quickly. If someone were to write up details on how to access various devices on the Handyboard though (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
 
  Re: 4WD 4WS model w/limited slip diff.
 
This photo might help (2 URLs) the rubber-band connection between the two power outputs, whenever the model would go over a bump and one wheel was lifted off the ground, the other wheel would not spin at all and all the power went to the other (...) (28 years ago, 9-Apr-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR