 | | Increasing current output to motors on HandyBoard
|
|
I am looking to drive a radioshack motor off my HB. Its rated at 9V - 18V. It claims that at maximum efficiency it will draw 1.98 Amps. My HB uses the TI sn754410ne motor controller and is rated only up to 1 amp. If i replace this unit with a L293b (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Web based LegOs compiler for the underprivileged?
|
|
(...) I am all over that! Might even be done tonight (EST) yet. -SMQ Shawn Menninga smq@dwarfrune.com --=--=--=--=--=--=--...-=--=--=-- "Well I've wrestled with reality for thirty-five years now, doctor, and I'm happy to state I've finally won out (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | re: legOS for the helpless
|
|
=>From: David Chen <nospam-dcchen@pacbe...et-nospam> =>... =>Since (I assume) there are many out there who are having a really tough =>time getting a working LegOs development environment working on their =>various systems (Mac, Winblows, etc...), (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | (canceled)
|
|
|
| |
 | | Re: Increasing current output to motors on HandyBoard
|
|
(...) Stacking the chips is doable but you will toast them when you get near their current limit. An easier solution is to use the TI chips to drive power transistors that are acting as voltage followers. This lets them take the current. (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Increasing current output to motors on HandyBoard
|
|
Another solution to this which is easier but more expensive is to use the output of the motor driver chip to drive solid state relays. You need the relays that use 5 volts for control and that will switch DC. The relays I use have flyback diodes in (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | rpm of the Geared motor
|
|
Anyone know the rpm of the Geared motor. Thanks LINC (28 years ago, 9-Apr-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: interactive C
|
|
I'll follow your suggest, thanks for the time you gave me. It has been very useful! Stefano ---...--- (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re : -> Interactive C
|
|
You help has been really useful, i'm going to visit thi slink immediately! Stefano Falconetti (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Even more remote controls
|
|
there are a few sites out there wif the required IR info.. I'll try and dig em up tomorrow morning.. I'm gonna get my self a blank GB cart, and the device to upload the data to the cart hopefully this comming friday.. -----Original Message----- (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | RE: rpm of the Geared motor
|
|
# From: ldsmith@pfc.forestry.ca # Sent: 09 April 1999 07:44 # To: lego-robotics@crynwr.com # Subject: rpm of the Geared motor # ---...--- # Anyone know the rpm of the Geared motor. # If you mean the one that comes with the RIS, it's 350. When I (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | Re: loading s/w
|
|
(...) legOS has a software solution built-in - when you are ready to quit, hold down the on/off button and press the 'prog' button. Hope this helps! Cheers, Richard (28 years ago, 9-Apr-99, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: rpm of the Geared motor
|
|
(...) About 360 rpm, according to my measurements. The non-geared motor runs at about 4200 rpm. (...) Regards, Johannes. (28 years ago, 9-Apr-99, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: Even more remote controls
|
|
(...) Since you can control the IR LED directly you should be able to get this all working in SW. You will need to modulate the IR with a 40Khz carrier. From there you then turn on and off the carrier to create the start, data and stop bits. This is (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | Re: Increasing current output to motors on HandyBoard
|
|
I wonder if this would last since a relay is mechanical and I would assume that it would wear with all that "switching". Doe anyone have any experience with this? Thanks. ---...--- ericson mar Robotics Consultant mar@cooper.edu (212)353-4356 (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: GCC 2.8.1 for HC11
|
|
(...) My favorite 68HC11 text resource is: 68HC11 Microcontroller by Joseph D. Greenfield Amazon Price: $87.50 (Wow! I'm sure I didn't spend nearly this much when I bought mine 3 years ago...) The sections on using the 68HC11 timers for interrupts, (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | On 9V battery box #5391 for projects
|
|
I recently got a 5391 9V battery box from S@H to put my RCX IRPD board into. I cut off all but 3 nubs worth of the box from the end with the switch and removed the battery tensioner at that back. The board fits in nicely with just the LEDs sticking (...) (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | Re: On 9V battery box #5391 for projects
|
|
(...) DOH! (URL) FRIDAY!!! (28 years ago, 9-Apr-99, to lugnet.robotics)
|
| |
 | | power supply questions
|
|
Hello all, I want to power the handy board using the 250watt 12V 9amp power supply of a PC. Any suggestions as to what I should take into consideration before attempting this. A buffer? A fuse? A straight hook up? Why is the HB not supposed to be (...) (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: interactive C
|
|
Dear Stefano, Visit el.www.media.mit.edu...index.html to find about the needed software. Mostly you will be needing ic.exe and some library files. You may need a new pcode. Yours sincerely, Nitin (28 years ago, 9-Apr-99, to lugnet.robotics.handyboard)
|