 | | Home made weight bricks and train base plates —Mathew Clayson
|
| | | Has anyone made thier own weight bricks? My thought was to hollow out the bottom of a brick with a dremel, then fill it with BBs. And finally glue a plate across the bottom. This could be useful to add weight to some of my smaller train MOCs, where (...) (20 years ago, 12-Aug-04, to lugnet.parts.custom, lugnet.parts.mod, lugnet.trains)
|
| | | |
| | | | | Re: Home made weight bricks and train base plates —Rob Hendrix
|
| | | | | "Mathew Clayson" <mathew_impact1@yahoo.com> wrote in message news:I2Cwvo.155L@lugnet.com... (...) fill it (...) to (...) to (...) colors (...) plates? A (...) I've built subassemblies and filled them with pennies to use for lift bridge weights. (...) (20 years ago, 12-Aug-04, to lugnet.parts.mod)
|
| | | | | |
| | | | | Re: Home made weight bricks and train base plates —David Laswell
|
| | | | | (...) Lead fishing weights will weigh more than copper BBs, and you might be able to build custom molds so you can melt weights and form them so they'll fit into an unmodified brick, both inside the tubes and in the larger cavity. (...) If you don't (...) (20 years ago, 13-Aug-04, to lugnet.parts.mod)
|
| | | | | |
| | | | | Re: Home made weight bricks and train base plates —Sonnich Jensen
|
| | | | | (...) Look at my page under Modifications (URL) go direktly there by this link: (URL) also have some cars 34 studs long (7 wide), and I am playing around with a new luggage car 16-20 studs long. Look under Createtions - Trains - there are a number (...) (20 years ago, 13-Aug-04, to lugnet.parts.mod)
|
| | | | | |
| | | | | | | Re: Home made weight bricks and train base plates —David Laswell
|
| | | | | | (...) that it might as well not be radioactive (half-life of 19*10^18 years), is the only non-toxic heavy metal (aside from the radioactivity, but you probably get that much radiation standing under direct sunlight) and combines easily with (...) (20 years ago, 13-Aug-04, to lugnet.parts.mod, FTX)
|
| | | | | | |
| | | | | | | | Re: Home made weight bricks and train base plates —Sonnich Jensen
|
| | | | | | | (...) I know there is tin in it, but lead - dont know. Its melting point should be a little above 100C. A friend of mine tells, that there should not be Cadmium in it, as Cadmium is toxic. (In our case they would probably end in a model rather than (...) (20 years ago, 17-Aug-04, to lugnet.parts.mod)
|
| | | | | | | |
| | | | | | | | | Re: Home made weight bricks and train base plates —David Laswell
|
| | | | | | | | (...) Lead is usually added in a very small amount to make it flow into fine detail better. It's probably only a few percent lead content, so handling it wouldn't bear anywhere near the same risk of lead poisoning that handling pure lead does. (...) (...) (20 years ago, 17-Aug-04, to lugnet.parts.mod)
|
| | | | | | | | |
| | | | | | | | | | Re: Home made weight bricks and train base plates —Mark Bellis
|
| | | | | | | | (...) Yes, always wash your hands after handling solder! (...) I see the melting point of standard solder (63% tin, 37% lead) is 183 deg C. If I held a soldering iron and a reel of solder over an invered brick and dripped molten solder into the (...) (20 years ago, 18-Aug-04, to lugnet.parts.mod)
|
| | | | | | | | |
| | | | | | | | | | Re: Home made weight bricks and train base plates —David Laswell
|
| | | | | | | | | (...) It's not just after handling it that you need to worry about. The acid in your skin will leech trace amounts from the surface, and you'll absorb it through your skin. You'd need to go out of your way to poison yourself in this manner, but you (...) (20 years ago, 18-Aug-04, to lugnet.parts.mod)
|
| | | | | | | | | |
| | | | | | | | | | Re: Home made weight bricks and train base plates —Mathew Clayson
|
| | | | | | | | (...) Unfortuneatly the drips of solder would not stick to each other, so unless you put a few drops of glue in afterwards to hold it all togather, you'd loos you weights. But this isn't a bad solution. It would fill the brick near solid, and the (...) (20 years ago, 19-Aug-04, to lugnet.parts.mod)
|
| | | | | | | | |
| | | | | | | | Re: Home made weight bricks and train base plates —Mathew Clayson
|
| | | | | | (...) Thanks guys, This will do nicely. I've used theis alloy before, but had no idea where to buy more. Mat (20 years ago, 19-Aug-04, to lugnet.parts.mod, FTX)
|
| | | | | | |
| | | | | Re: Home made weight bricks and train base plates —Mark Bellis
|
| | | | (...) Better still, avoid the dremel by buying second hand some old 2x4s, which have no tubes underneath. Fill with plasticine or similar denser material that doesn't get too hot (i.e. not solder), leaving 1.6mm depth free for the studs of the brick (...) (20 years ago, 13-Aug-04, to lugnet.parts.mod)
|
| | | | |
| | | | | | Re: Home made weight bricks and train base plates —Mathew Clayson
|
| | | | (...) Mark, The old hollow brick sounds OK, but I'd want them in new looking black ABS, or dark grey. Besides, once I glue it shut, the world will never know! Trust me I know how to use a dremel. I've seen your work, very nice. I 've also made train (...) (20 years ago, 19-Aug-04, to lugnet.parts.mod)
|
| | | | |
