Subject:
|
Re: Experimenting with Brasso (tm)
|
Newsgroups:
|
lugnet.general
|
Date:
|
Tue, 21 Dec 1999 19:45:56 GMT
|
Viewed:
|
1014 times
|
| |
|
|
Has anyone ever tried using Brasso with a toothbrush? It seems that it would
work better on the textured 2x3 slopes. I personally used Brasso, with a
cloth, to remove the printing from the McDonalds sets. I was surprised to
see that once the printing was removed that the brick was just as smooth and
glossy as before the printing was applied.
After that success and with a 99.97% full can of Brasso <g> I tried
removing slight scuff marks from a few other pieces. Not only did it appear
to remove the scratches, it brought back the original luster.
-Nick
Paul Davidson wrote in message ...
> I tried letting some pieces sit awhile and soak, but it didn't seem to
> matter.
>
> --
>
>
> Paul Davidson
>
> Dave Schuler <orrex@excite.com> wrote in message
> news:Fn3IDo.3qo@lugnet.com...
> > In lugnet.general, Craig Hamilton writes:
> > > In lugnet.general, Paul Davidson writes:
> > > > I tried it with several of the smooth McDonald's slopes (pictures of
> > > > Grimace), and with one 2x1 tile ($100 bill print).
> > > >
> > > > Result: the print comes off, but it takes a lot more work than I • expected.
> > > > I had to spend at least five minutes on a single piece, rubbing • furiously.
> > > > For the first little bit, you make no apparent progress whatsoever. • The
> > > > finished pieces were not damaged in any way. All in all, Brasso works, • but
> > > > you'd better be ready to earn those new pieces. :)
> >
> > > brasso also works well to clean dingy old pieces with worn in stains. • be
> > > sure to rinse off, and dry your pieces when you're done.
> >
> > Does it make a difference if you allow the Brasso to set for awhile? • That
> > is, if you apply some to the brick and let it soak before trying to buff • off
> > the printing?
> >
> > Dave!
>
>
|
|
Message has 3 Replies:
 | | Re: Experimenting with Brasso (tm)
|
| (...) Hmmm... If I can get some of this stuff, I'll try it on a 1x8 brick I have. This brick was left in the sun for so long that it has yellowed to the point of beinging virtually the same color as the beige bricks. Jeff P.S. It was part of a (...) (25 years ago, 21-Dec-99, to lugnet.general)
| | | Re: Experimenting with Brasso (tm)
|
| (...) After seeing these posts, I went to the hardware store and popped $3.69 on a can of Brasso to test it on one of my hated UFO panels. It really does work--it's both a mild abrasive and a polymer-solvent, so it takes scratches out likely by a (...) (25 years ago, 21-Dec-99, to lugnet.general)
| | | Re: Experimenting with Brasso (tm)
|
| Is this something that one could mechanise? Ala a buffing wheel or the like. Purely hypotehtical question for me, the thought of actually removing printing (even happy meal printing) makes me blanch, Blanche! (25 years ago, 23-Dec-99, to lugnet.general)
|
Message is in Reply To:
| | Re: Experimenting with Brasso (tm)
|
| I tried letting some pieces sit awhile and soak, but it didn't seem to matter. -- Paul Davidson Dave Schuler <orrex@excite.com> wrote in message news:Fn3IDo.3qo@lugnet.com... (...) expected. (...) furiously. (...) but (...) be (...) That (...) off (...) (25 years ago, 21-Dec-99, to lugnet.general)
|
29 Messages in This Thread:
  
 
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
