To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.cad.dev.org.ldrawOpen lugnet.cad.dev.org.ldraw in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 CAD / Development / Organizations / LDraw / 427
426  |  428
Subject: 
Re: Voting page for 9906
Newsgroups: 
lugnet.cad.dev.org.ldraw, lugnet.cad.dev
Date: 
Tue, 3 Aug 1999 08:41:50 GMT
Viewed: 
3893 times
  
> 2552 - The lines that make up the "creases" in the indented corners are angled,
> and they shouldn't be.  I feel this is very important.  There also is an extra
> line floating around in the pit.

i promise to fix the pit extra line asap.also about the corners... i can fix those
as well. thanks for pointing out the mistake.

> 606p33 - The center line is obviously a slightly thinner line drawn over the
> dashed lines of another straight roadplate.

my mistake. i thought i could make this by changing the color of the grey bits on
the dashed roadplate to white i could make it work. my fault. i will invistigate
the part some more.

> 608p33 - There are some extra quads in the area where the crosswalk would be if
> this piece was a normal road plate.

what is the problem here? do you mean that the fact that i used lots of quads here
instead of one is a problem? how? does it affect the use of the part?

> 609p33 - The green lines have black borders, when they should be Dark Gray I
> think.

there is no 609p33.dat in the current vote... do you mean 609p01.dat? in that case
i can fix the problem here... i can change the color easily

> x610 - The gray line on the right side is too thin.

will fix asap

> x611 - Pattern corners aren't lined up properly, the gray lines don't touch the
> left and right sides.


will fix asap

> x612 - Pattern corners aren't lined up properly, the gray lines don't touch the
> left side.


will fix asap

> These two road plates have square corners even though they have the curved
> lines:
> x613p01
> 609p01


what do you mean? do you mean that the corner of the plate itself should be square
not round???

> Many of these *will* cause me to vote 'No' on the piece in question.
> 
> Jeff

i will fix all of these problems (if i can) asap



Message has 2 Replies:
  Re: Voting page for 9906
 
(...) i would just like to say that i am prepared to admit that the roadplate parts probobly were not redy for voting on but on the 32 x 32 raised with ramp the mistakes on the corners and also the line in the pit were all honest mistakes. (27 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
  Re: Voting page for 9906
 
(...) Well, in LDLite, it looks like there is a faded crosswalk when shading is turned on. It looks really bad, IMO. (...) Oops, my bad. Yes, I meant 609p01. Thanks for changing the color. Now it'll match the current road plates. Talkin' 'bout the (...) (27 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)

Message is in Reply To:
  Re: Voting page for 9906
 
(...) Okay, I looked at the pieces, and here are my thoughts on the ones I had problems with: Can the insertion points for the castle doors be moved closer to the hinged part? Not a big deal, it just kinda bugs me. ;) 2552 - The lines that make up (...) (27 years ago, 2-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)

26 Messages in This Thread:











Entire Thread on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact

This Message and its Replies on One Page:
Nested:  All | Brief | Compact | Dots
Linear:  All | Brief | Compact
    

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR