 | | Re: Discussion of Train Table Sizes
|
|
(...) Sprinters come in short and long wheelbase versions as well as in low and high roof versions (so you get 4 possible cubics, plus all the door and window options). I bet the long wheelbase Transit is about the same capacity, or perhaps smaller, (...) (20 years ago, 16-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) The standard thing for UK model railway exhibitions is that the organisers pay travelling expenses (i.e. van hire and petrol (gas)) within reason and normally provide lunch for exhibitors. (Traders of course have to pay to be there) (...) A (...) (20 years ago, 16-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) Sorry, two questions - First, model railway clubs pay you to hire a van? How does that work? Why would they pay you? Second, did you realize that while some enlightened Americans may have heard of a Ford Transit, they've probably never seen (...) (20 years ago, 16-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) I'm surprised you would use inches as your base measurement, since you are based in Europe. Why didn't you just use the simple formula 1 stud = 8 mm? (20 years ago, 16-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) I sub-contracted this to a model railway board builder. The boards I have ATM cost £26.80 each plus £9.90 per double leg, and I have 20 of each. This came to £742, a considerable investment! Add to this sneeze guards made from 14 pieces of (...) (20 years ago, 15-Dec-04, to lugnet.trains.org)
|
| |
| | Train Table Height [was: Discussion of Train Table Sizes]
|
|
(...) To the best of my knowledge, no. General model railroading practice seems to be 36 inches. Some LTCs use this height. Most clubs of which I know use 30 inches (this is the nominal height of banquet tables, and easily achieved with standard (...) (20 years ago, 15-Dec-04, to lugnet.trains.org)
|
| |
| | Re: GFLTC at GATS Tampa this weekend (Dec 18-19)
|
|
Note: wrong dates listed... It should be December 18-19, 2004. (...) (20 years ago, 15-Dec-04, to lugnet.trains.org, FTX)
|
| |
| | GFLTC at GATS Tampa this weekend
|
|
Hi all, The Greater Florida LEGO Train Club will have a layout at the Great American Trains Show (GATS) December 11-12, 2004 in Tampa, Florida. The 28ft X 16ft layout will feature two main lines of trains, a Monorail line, a large yard area, a large (...) (20 years ago, 15-Dec-04, to lugnet.announce, lugnet.trains, lugnet.trains.org, lugnet.loc.us.fl, lugnet.org.us.gflug)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) Hi all, I did use the measure of 30 and 7/32nds, with gives us 767,55625 millimeters, and rounded them up to 768mm. This is indeed a bit too much, because we got also problems with bridges (96 studs long) mounted on a table 30 bricks below the (...) (20 years ago, 14-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
The GMLTC uses 40"x60" plywood tables with custom-built aluminum frames underneath and heavy-duty folding legs. Some pros and cons: - Pro: Plenty of room! After we trashed our last layout, we consciously decided to build "larger" this time: 8-wide (...) (20 years ago, 14-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) Funny you should mention that. I just bought 6 of that very type of banquet table for the traveling TCLTC layout yesterday ($41 each from Costco). I really like these tables and am excited about using them. I should also say that we've also (...) (20 years ago, 13-Dec-04, to lugnet.trains.org, FTX)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) Kevin- That's an unsolved problem for us that gets worse when we are in a hurry and as the layout gets larger. When we are not rushed, we losen the bolts a little and jiggle things until the square tables just fall into place. For our current (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) I should point out that at SCLTC, we initially provided spring clamps for temporary connection ($0.99 each) or until bolts were installed, but decided that they really were not necessary. We use wing nuts and just fasten the bolts finger (...) (20 years ago, 13-Dec-04, to lugnet.trains.org, FTX)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) Kevin- I agree totally that making tables is -- or can be -- a lot of work. If all we ever did with the tables was set them up at matching heights at a show and then lay LEGO on them, it would definitely NOT be worth it. What does make it (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
Here is what NELUG uses. Most of our tables are 40.25" x 40.25" or 4x4 32x32 baseplates. The extra .25" is to account for the fact that the baseplates are not exactly 10" square but ever so slightly larger. We also use some 40.25" x 20.125". Finally (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) The NBLTC has adopted a modular approach using 80 studs wide x 160 studs long standard table (module) size. This works for us but the overall design allows for a multitude of arrangements and optional sizes within the modular concept. (...) (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) We don't do anything to secure the tables. We just position the tables where we want them and that is all. So far, we have never had a problem. If the tables move a little bit, we just give them a shove back in place. A few small table gaps (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) We thought about that too, but decided we had to build custom tables or they might spread apart, causing derailments. How do you keep them together? Do you clamp them or something? (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
I have always been incredibly impressed by SCLTC tables. Heck, I am always impressed by SCLTC layouts, too. All custom-built tables are impressive to some degree. Here at LUCNY, us crazy New Yorkers discuss building our own tables regularly, but (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
| |
| | Re: Discussion of Train Table Sizes
|
|
(...) SCLTC builds its own tables from 0.240 inch thick melamine coated hardboard and uses 1.910 inch diameter black ABS pipe for the legs. Both materials are cheap and readily available. The drawback to the hardboard is that it is not waterproof, (...) (20 years ago, 13-Dec-04, to lugnet.trains.org)
|
