 | | RE: New Parts
|
|
(...) Its already there, as ... (...) ... they already do! Been there, done that! :-) William (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | RE: New Parts
|
|
(...) To (...) This would come in handy, if there is room I tend to use a #3 axle and two half bushings but it's not always possible. And quite often unsightly, especially on digger/excavator boom arms. William (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: DETAILS: 8011 Jango Fett & 8012 Super Battle Droid
|
|
(...) They're also in 8010 Darth Vader. A 1x2 liftarm is part I've been wanting for a long time. I'm really happy that there are an abundance of them in the new sets. (...) They're better (in some respects) than an ordinary ball-n-socket because (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: DETAILS: 8011 Jango Fett & 8012 Super Battle Droid
|
|
(...) The new #2 liftarms seems nice, I know they're in R2D2 aswell. (...) Some other bloke also mentioned this to lugnet.build.mecha but I find your information a lot better e.g. how though they are etc.. Compared to the Bionicle joints how though (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
(...) If you press a piece that fits a minifig's hand inside the 3/4 pin it becomes slightly less "wobbly". Seems to work better with other pins though. (...) This would come in handy, if there is room I tend to use a #3 axle and two half bushings (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
(...) I said "most times" :) I guess you can't put an half bushing between the frame and wheel thus making the drive axles one stud wider in total, the axles could meet half-way in the beams. (...) Personally I'd cut a #10 since I own more of these (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | RE: New Parts
|
|
Ah, but you were asking for parts we want not fudges we can achieve! I want the ridge intact in the correct place! I can make 7U axles as well! William -----Original Message----- From: news-gateway@lugnet.com [mailto:news-gateway...net.com]On Behalf (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
This is any easy one, the only tool you need is a pair of little electronics type diagonal cutters like Radio Shack sell for about $5 I think - red plastic coated handles made from die cut sheet metal. You can use them to nip the ridge off from (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | MoTeC March: Vote now!
|
|
FUT lugnet.technic Hi all! New month and time to vote for the best Technic MOC in the Monthly Technic Contest - MoTeC. Vote here: (URL) you want to submit your own model for April, read here: (URL) months winner will be announced shortly. /Tobbe (...) (23 years ago, 2-Apr-02, to lugnet.announce, lugnet.build.contests, lugnet.robotics, lugnet.modelteam, lugnet.technic)
|
| |
| | DETAILS: 8011 Jango Fett & 8012 Super Battle Droid
|
|
I made a quick trip to Wal-Mart last night[1] and discovered all the new 2002 SW sets (except for the Yoda sculpture). Here are pictures of the parts and a few close up shots: 8011 Jango Fett $30: (URL) Super Battle Droid $35: (URL) haven't had time (...) (23 years ago, 2-Apr-02, to lugnet.technic, lugnet.build.mecha, lugnet.starwars)
|
| |
| | RE: New Parts
|
|
Now two parts I *would* pay for A black friction version of the 3/4 dark grey pin. If you attach a half width studless beam/liftarm to a full width beam with two of the dark grey ones it more often than not wobbles too much - I want a nice tight (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | RE: New Parts
|
|
I agree - but then ... Check out my variation of Jennifer's Bobcat at (URL) and if you look closely at "...squeeze.jpg" you'll see that the rear axle on the left protrudes slightly - that's because it really needs to be a 7U one - The same is also (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
Yeah, Roboslizonicles are a great source of supply of "raw" material ;) The part you describe yields a ball with a short length of cross axle attached from the other end when you chop it up as well. With some of these highly specialised parts, I try (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
You are right. That would be cool ! Ross Crawford <rcrawford@csi.com> wrote in message news:GtxDzw.Gp6@lugnet.com... (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
(...) Most times an #4 connected with a #3 or a #5 and #2 works but it could be nice sometimes, yes. /Tobbe (URL) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
There are two different "carrier disks". One has a center round hole, the other a center cross axle hole. They both have a pair of cross axle holes and pair of round holes around the outside. The cross axle holes are used to pin the two disks (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
How about the special right-angle skew gears (IIRC that's the proper name for them.) that are commonly used for the connection from the crankshaft to the distributor cap in most petrol-driven engines? Modern electronic engine management technologies (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
April Fools aside and at the risk of offending purists I've started cutting up the 32173 Technic Liftarm 2 x 7 with 2 Ball Joints Cutting off the fake rams and the one ball joint which is off at an angle leaves a ball joint with a two hole beam (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
I was thinking along the lines of the old planetary gearboxes where different gear ratios could be selected by applying a brake to the appropriate anulus. ROSCO "Xanthra47" <jmantor@nycap.rr.com> wrote in message news:GtxCHy.CyG@lugnet.com... (...) (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
| |
| | Re: New Parts
|
|
We don't even need that. Two of John's Internal gear bricks, two carriers, some pinions and some axels are enough for a two stage planetary set. Drive the first stage "sun" with a pinion on a technic gear motor, connect the output of the 1st carrier (...) (23 years ago, 2-Apr-02, to lugnet.technic)
|
