 | | Exp. board Servo
|
|
Hi.. i have some questions about the exp. board and R/C servo, hope anyone can help me.. thanks.. From the "Expansion board software" homepage, it said that servo0=(value) is used to control the servo, may i ask how can i convert this value to (...) (25 years ago, 29-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | HB memory capacity
|
|
Hi all, A funny thing happened. i tried to download a file. IC gave the message it was downloading, but just when it finishes it gives me an error saying "lost synch with board". then i unloaded some files and redownloaded the file again. this time (...) (25 years ago, 29-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: KIPR Kit
|
|
Joe, As it turned out, the edge of the pulley was right next to and perpendicular to a long beam piece. We just used hot glue to glue it to the beam and held it in place until the glue dried and had no trouble at all. The pulley can't come out of (...) (25 years ago, 29-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: KIPR Kit
|
|
(...) These are what I also have been trying to use to break the beam, they seem to be the best choice. My question was more about how you mounted the sensor. I'm curious to know what piece people had glued the sensor to, and to see if they used (...) (25 years ago, 29-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo controllers
|
|
(...) If you can burn PIC processors yourself, try my page at (URL) and bonk on the serial servo controller project. I have PIC12C508 code there that allows you to control 4 servos with a single 2400 baud connection. The code is set to allow a (...) (25 years ago, 28-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Servo controllers
|
|
Yes, there is a way. Check out the serial servo controllers at (URL) one of these that you use controls up to 8 servos, and you can chain a bunch of them together and go servo nuts. -- Will Bain P.S. -- I haven't yet tried these myself. I'm curious (...) (25 years ago, 27-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Problem on loadind Expansion board files
|
|
The problem is simply that the new expansion board code supercedes a couple of functions in the old lib_hb.c (and possibly in lib_hb.icb, too; I can't remember). If you go to the HB web site, you'll find a new version of lib_hb that's compatible (...) (25 years ago, 27-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | RE: Solar charging and OWI Arm
|
|
Whatever portion of the 40 mA that the HB requires for it's operation will "float over" the battery pack and be consumed by the board. The rest goes into the battery to recharge it. I haven't measured the current draw of my robot, but of course your (...) (25 years ago, 27-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Servo controllers
|
|
I understand that a handyboard in combination with the expansion provides a total of 6 servo motor controllers. However, I need 12 controllers. Is there any other ways to achieve this other than buying another set of handyboard + expansion board? (...) (25 years ago, 27-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | persistent globals
|
|
Hi all Has anyone worked on persistent global variables. In the manual it says persiststents can keep their value on reset conditions and multiple downloads. i declared persistant globals in my program and they do keep their value on reset (...) (25 years ago, 27-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Problem on loadind Expansion board files
|
|
hi all, I had post a message about the exp board days before. Actually, the problem had not been solved yet. I post the following message that was shown when I was trying to load the exp files to the board. I don't know why this happen, since my (...) (25 years ago, 27-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Solar charging and OWI Arm
|
|
Oops. I just realized I forgot to tell you how to connect the solar panel. Solar panels are almost always installed with a diode to block reverse voltage that would actually suck energy out of your battery when the sun goes down. For a small solar (...) (25 years ago, 27-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: Solar charging and OWI Arm
|
|
Any 12 V solar panel would help to add some juice to the battery, but the board probably can't live on just 40mA. The recommended adapter is 500 mA, which would charge the battery about a dozen times faster. Still, I have some solar cells just (...) (25 years ago, 27-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Solar charging and OWI Arm
|
|
Hi, Has someone builded a battery charger for the HB, using a solar panel, is a 12 v / 40 mA panel enough for that?, and how to connect it?. Also, has someone tried the OWI robotic arm ? Thank You Jose Luis (25 years ago, 26-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: HandyBoard A/D converter?
|
|
This calls for a signal conditioning amplifier. Since you're not worried particularly about slew rate (the handyboard won't do much more than 12khz sample rate) you can pretty much use any op-amp you want. Ideally you'd use a single supply one, set (...) (25 years ago, 26-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: HandyBoard A/D converter?
|
|
The 68HC11 has references for the range of the A/D converter. In the HB design they are hardwired to 0 and +5. I believe the pin is Vrh at (URL) and is currently wired to +5. --chris prosser From the motorola manual: 2.2.7 A/D Reference and Port E (...) (25 years ago, 26-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: colour sensor caliberation
|
|
May I suggest you test your system for response to invisible light? You could shine an Infrared LED onto it to see what you read. There are also "UV Cutoff" Filters available at photography shops supplying color darkroom equipment (UV from the bulb (...) (25 years ago, 26-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | Re: KIPR Kit
|
|
Hi, In the kit you will find a number of pulleys about 1 inch in diameter. These are narrow enough to fit through the sensor. They have six holes in them and if they are on an axle, will give you 12 pulses per revolution - 2 pulses per hole. One (...) (25 years ago, 26-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | HandyBoard A/D converter?
|
|
Dear Handy Board Masters, I am trying to use the handy board for some A/D conversions. The converter is set up on a 5 volt scale, the converter is an eight bit converter. Over this range I get a resolution of 19.5mV per Step. My application is (...) (25 years ago, 26-Feb-00, to lugnet.robotics.handyboard)
|
| |
| | LUGNET spammed (was: Semiconductor Specific Search Engine)
|
|
Hey, folks, (and Todd Lehman in particular) Did you catch this spam over in lugnet.robotic.handyboard? I hope that this trend doesn't continue. :^( LUGNET is one of the few Internet institutions I use that is nearly 100% content, and spam-free. (...) (25 years ago, 26-Feb-00, to lugnet.robotics.handyboard, lugnet.general)
|
